A wooden box beam is fabricated from four boards, which are fastened together with nails as shown. The nails are installed at a spacing of s = 125 mm, and each nail can provide a resistance of V; = 875 N. In service, the box beam will be installed so that bending occurs about the z axis. Determine the maximum shear force V that can be supported by the box beam based on the shear capacity of the nailed connections. 25 mm 200 mm 25 mm 40 mm 120 mm 40 mm O 5.38 kN O 4.21 kN O 3.24 kN O 6.09 kN O 4.49 kN

A wooden box beam is fabricated from four boards, which are fastened together with nails as shown. The nails are installed at a spacing of s = 125 mm, and each nail can provide a resistance of V; = 875 N. In service, the box beam will be installed so that bending occurs about the z axis. Determine the maximum shear force V that can be supported by the box beam based on the shear capacity of the nailed connections. 25 mm 200 mm 25 mm 40 mm 120 mm 40 mm O 5.38 kN O 4.21 kN O 3.24 kN O 6.09 kN O 4.49 kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A loaded beam, 60 mm wide by 100 mm high and 6 m long, has the shear and moment diagrams as shown below. Determine (a) the magnitude, type and location of the maximum flexural stress (in MPa) (b) the stress (specify the type) in a fiber 30 mm from the top of the beam at a section 3.5 m from the left end. I = bh3/12
The beam is constructed from two boards fastened together at the top and bottom with three rows of nails spaced every 8 in. If an internal shear force of V = 800 lb is applied to the boards, determine the shear force resisted by each nail.
If the beam has a rectangular cross-section, then the shear-stress distribution will be parabolic. True or False?
Calculate the maximum normal and shear stress values for the attached beam at x = 8.5 m. Determine the distribution of the shear stress in the cross-section in the y-axis direction at y=55 mm, y=109.99 mm and y=110.01 from top. The dimensions of the beam are a = 5.5 m, b = 3.0 m and c = 2.5 m, and the cross-sectional dimensions are d = 170 mm and h = 130 mm. The distributed load of the beam has the value q = 3kN / m and the force F = 10kN.
2. The W360 x 262 section carries a vertical shear force of 650 kN. For this section, calculate:(a) the minimum shear stress in the web;(b) the maximum shear stress in the web and(c) the percentage of the vertical shear force carried by the web.
Three plates are welded together to form the section shown. Dimensions of the cross section are b = 5.1 in., d = 15.3 in., a = 3.6 in., and t = 0.8 in. For a vertical shear force of V = 40 kips, determine the shear flow through the welded surface at B.
Beam cross section is shown below. If a resultant shear force, V acting at the beam cross section is 40 kN, (a) Determine the shear stress due to bending at points C (b) Sketch the shear stress distribution over the beam cross section and describe the shear stress pattern at the interface between flange and web. Given I NA = 301.3 x 10-6 m4
The H-beam is subjected to a shear of V = 80 kN. Sketch the shear-stress distribution acting along with one of its side segments. Indicate all peak values.
A cold drawn steel rod of circular cross-section is subjected to a variable bending moment of 565 Nm to 1130 N-m as the axial load varies from 4500 N to 13 500 N. The maximum bending momentoccurs at the same instant that the axial load is maximum. Determine the required diameter of the rodfor a factor of safety 2. Neglect any stress concentration and column effect. Assume the followingvalues:Ultimate strength = 550 MPaYield strength = 470 MPaSize factor = 0.85Surface finish factor = 0.89Correction factors = 1.0 for bending= 0.7 for axial load
These garden shears were manufactured using inferior material. Using a loading of 50 lb applied normal to the blades, and appropriate dimensions for the shears, determine the absolute maximum bending stress in thematerial and show why the failure occurred at the critical location on the handle.
Determine the maximum absolute values of the shear and bending moment.
The double-web girder is constructed from two plywood sheets that are secured to wood members at its top and bottom. The allowable bending stress for the wood is σallow = 8 ksi and the allowable shear stress is τallow = 3 ksi. The fasteners are spaced s = 6 in. and each fastener can support 400 lb in single shear. Determine the maximum load P that can be applied to the beam.