A. The baseband signal m(t) = 5 sin (3000nt) Is transmuted by using a linear delta modulation (AM), the modulator has the following specifications Sampling rate = 10 Fnyquist, where Fnyquist is the Nyquist rate of the baseband signal, bandwidth = 10 KHz. 1. Determine the maximum step size A for delta modulation of this signal, which required avoiding slope overload.

A. The baseband signal m(t) = 5 sin (3000nt) Is transmuted by using a linear delta modulation (AM), the modulator has the following specifications Sampling rate = 10 Fnyquist, where Fnyquist is the Nyquist rate of the baseband signal, bandwidth = 10 KHz. 1. Determine the maximum step size A for delta modulation of this signal, which required avoiding slope overload.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1.) Answer the following: a. At 50% modulation DSBSC, what is the percentage power saving?b. At 75% modulation, what percentage of the total transmitted power is in the sideband?c. For conventional AM, the useful power, that is, the power that carries the information is rather small reaching a maximum of ______.Select the correct response:-One-fifth of the total signal power at 100% modulation-One-third of the total signal power at 100% modulation-One-fourth of the total signal power at 100% modulation-One-tenth of the total signal power at 100% modulation
Bandwidth requirements:a. Find the minimum required bandwidth for the baseband transmission of a 32-level PAM pulse sequence with a data rate, R of 10000 bps if the system transfer characteristic consists of a raised-cosine spectrum with 100% excess bandwidth (roll-off, r = 1.0).b. Find the minimum required double-sideband (DSB) bandwidth for transmitting the modulated PAM sequence where the system transfer characteristic is the same as in part (a).c. Repeat part (a) with roll-off, r = 0.5.d. Repeat part (b) with roll-off, r = 0.5.e. Repeat part (a) with roll-off, r = 0.f. Repeat part (b) with roll-off, r = 0.
5. Why must modulated signals be demodulated?A. To recover the original intelligenceB. To improve the spectral efficiency of digital transmissionsC. To enable implementation of advanced featuresD. To produce one or more significant sideband pairs
An analog signal is given as?(?) = 5 + 2 cos(20??) + 3 cos(400??)a) What is the bandwidth of ?(?)? Determine the Nyquist sampling frequency for ?(?), both in radian/sec (?? ), and in Hz (?? ).b) Formulate ?? (??), the signal sampled with the Nyquist frequency.c) Plot frequency spectrum of the sampled signal, ?? (??).d) Determine the filter to reconstruct the signal ?(?).e) Is it possible to reconstruct the signal ?(?) for ?? = 0.004 [s]? State that if aliasing error occurs or not.
[Q1] A carrier signal (peak amplitude = 39V, frequency = 100MHz) is frequency modulated by the baseband signal (peak amplitude = 5V, bandwidth = 12.02kHz). The frequency deviation is 77.53kHz, and the load is 510. Determine (a) the load power, (b) the bandwidth of nsmitted signal. (consider only VnG)|> 0.1).
For an FM modulator with a modulation index mf = 1, a modulating signalVm(t) = Vm sin(2π1000t) and unmodulated carrier Vc(t) = 10 sin(2π500kt),determinea) Number of sets of significant sidebandb) Their amplitudec) Then draw the frequency spectrum showing their relative amplitudesd) Determine the unmodulated carrier power for the FM modulator(assume a load resistance RL = 50 Ω)e) Determine the power in the modulated carrier and each side frequency,and sketch the power spectrum for the modulated wave.
A carrier is modulated simultaneously by two baseband signals with modulation indices of 0.3 and 0.4 respectively. If the scheme is AM, then what will the overall modulation index?
1. For a system with FM modulation, the amplitude of the unmodulated carrier is 12Vp, if the modulation index is 1.5 and the load resistance RL is 10 ohms,a) determine the power in the unmodulated carrier; b) Determine the power at the carrier frequency and at each significant side frequency for the modulated wave. What value of power do you obtain when adding the values obtained in question (b)?
1. Select the correct statement(s) regarding amplitude modulation (AM). a. If the AM Index is greater than 1 (i.e., µAM>1), then over modulation occurs leading to signal distortion b. With AM, the message is captured as amplitude changes to the carrier’s amplitude. c. The AM modulated carrier bandwidth is dependent upon the baseband signal’s frequency bandwidth d. All of the above are correct 2. What is true about the frequency bandwidth of a modulated electrical or electromagnetic (EM) signal? a. signal bandwidth is only determined by the frequency of the unmodulated carrier wave b. modulation technique and the amount of information transmitted determines the signal’s bandwidth c. only the baseband signal determines frequency bandwidth; i.e., modulation technique has no impact on bandwidth d. a and c are true 3.Regarding carrier modulation, identify the carrier signal variable(s)…
What are the advantages and disadvantages of single-sideband transmission? Briefly describe each.
-MCQ- FM modulator is used to transmit a cosine message signal with 4V amplitude and 20Hz frequency. The frequency deviation constant kf = 25 Hz/V, the carrier is a cosine sign with an amplitude of 10V and a frequency of 2000Hz. The FM modulated signal is passed through a bandpass filter and 90% of the power of the modulated signal remains. What is the bandwidth of the FM modulated signal in this case? a) 240hz b) 20hz c) 100hz d)200hz
For double sideband (DSB) signal f) What is the difficulty of synchronous demodulation (coherent detection)? g) Compare between the ordinary amplitude modulation (AM), and double sideband (DSB) modulation in terms of transmitted power, complexity of demodulation, receiver cost, and bandwidth