b) An aluminium rod is attached between a steel rod and a bronze rod as shown in Figure-3. The axial loads are applied at the positions indicated. Determine the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminium of 90 MPa, and in bronze of 100 MPa. Aluminium A-400 mm Steel Bronze A-550 mm A-250 mm 2P 4P P 3.0 m 2.5 m 2.0 m

b) An aluminium rod is attached between a steel rod and a bronze rod as shown in Figure-3. The axial loads are applied at the positions indicated. Determine the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminium of 90 MPa, and in bronze of 100 MPa. Aluminium A-400 mm Steel Bronze A-550 mm A-250 mm 2P 4P P 3.0 m 2.5 m 2.0 m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.3P: A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the...

See similar textbooks

Similar questions

-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A Steel wire hangs vertically under its weight. What is the greatest length it can have if the allowable tensile stress o,-200 MPa Demity of steely 80 kN/m
A steel bar ABCD consists of three sections: AB is of 20 mm diameter and 200 mm long, BC is 25 mm square and 400 mm long, and CD is of 12 mm diameter and 200 mm long. The bar is subjected to an axial compressive load which induces a stress of 30 MN/m 2 on the largest cross-section. Determine the total decrease in the length of the bar when the load is applied. For steel E -- 210GN/m 2. [0.272 mm.] Could you please answer this fully? If you use * can you explain whatyou mean by it. Thank you
@2 The support consists of solid brass post surrounded by a steel tube. Before the load is applied, the gap between these two parts is | mm. Given the dimensions shown in the figure, determine the greatest axial load that can be applied 0 the rigid cap A if the maximum allowable stress in brass is (Guiin)se = 150 MPa and the maximum allowable stress in steel is (Gun ) = 200 MPa. E, = 200 GPa and Ey,= 100GPa.
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa Determine maximum load P for block shear
A Steel wire hangs vertically under its weight. What is the greatest length it can have if the allowable tensile stress st =200 MPa, Density of steel g=80 kN/m3.
A thick wall cylinder has 50 mm thick and internal diameter of 300 mm. If stress is limited to 30 MPa, determine the maximum internal pressure. A. 8.1 MPa C. 8.3 MPa B. 8.2 MPa D. 8.4 MPa
A seamless cylinder of storage capacity of 0.03m3 is subjected to an internal pressure of 21 MPa. The allowable stress in the material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder
The rigid bar AB shown below is supported by a steel rod AC having a diameter of 20 mm, and a block. Ignore the weight of AB and AC, and the distributed load on AB is p = 4.0 KN/m. Determine the axial normal stress developed in AC: = ____ MPa. Calculate your answer to 1 decimal place.
Two solid cylindrical rods support a load of P = 27 kN as shown. Rod 1 has a diameter of 16 mm and the diameter of rod 2 is 12 mm. Ø A. Determine the axial normal stress in Rod 1 (MPa). Ø B. Determine the axial normal stress in Rod 2 in MPa.
The connection consists of a plate connected to another plate by four 22 mm diameter rivets. It carries a load P = 60 kN at a distance of 165 mm from the centroid of the rivet group. Determine the shear stress on each rivet due to force alone, in MPa. Determine the shear stress on each rivet due to torsion alone, in MPa. Determine the shear stress on the highly stressed rivet, in MPa