An apartment has the dimensions 18 m by 9 m by 6 m. The temperature is 35°C, and the relative humidity is 52 percent. What is the total mass (in kg) of water vapor in the air in the apartment?

Q: An element of a ductile material on the free surface of a component is subjected to the stress…

A:

Q: Calculate the support reactions at A and B for the loaded beam. Assume P = 143 lb, w = 92 lb/ft, a =…

A:

Q: Determine the reactions at the supports of the beam which is loaded as shown. Assume w₁660 N/m, w₂ =…

A:

Q: For the manometer shown in Fig. calculate the pressure between points M and N. X Water Oil of RD =…

A: Manometer is used to measure the pressure difference the two points M and N.Assume density of water…

Q: The air duct of the heating system of a hall, an electric heater placed inside and It consists of a…

A:

Q: Take P-640 lb. (Figure 1) Part A Determine the horizontal and vertical components of force that the…

A: Given data is

Q: We want to design a wagon system like the one below while filling the kiln with coal at the Coke…

A: givenW=500 kgf=4905m=

Q: A shaft ABC is subjected to a couple moment at the middle of segment AB and point load at point…

A: The force at C, F = 100 lb

Q: TASK A hydraulic cylinder with a bore radius of 100 mm and an outer radius of 200 mm has been…

A: Pressure = 200 MpaTo find:Radial and circumferential stress using Lame's equationMaximum shear…

Q: Water (₁ = 62.4 lb/ft³) flows in a pipe. If the manometer connected as in Fig. is used with mercury…

A:

Q: The pump of a water distribution system is powered by a 15-kW electric motor whose efficiency is…

A:

Q: -Find the factor of safety of the post BD using the langer-static criterion, Draw the the langer…

A: Here are the steps needed to use the Langer-static criterion to determine the post-BD safety…

Q: Two forces are applied to an AISI 1050 HR post BD, as indicated. Knowing that the cross section of…

A: Cross-section of the vertical part, A = 1.5 in x 2.4 inThe yield strength for AISI 1014 HR steel, Sy…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5…

A: Diameter of tie rod (1): 5 mmDiameter of pin at B: 7 mma = 560 mm (distance between bracket A and…

Q: The total friction mean effective pressure of a 4-cylinder SI engine has a quadratic function with a…

A: please refer handwritten solution

Q: 3. The 30-kg gear A has a radius of gyration about its center of mass O of ko = 125 mm. If the 20-kg…

A: Given:mass of the gear= 30 kgradius of gyration ko=0.125 mmmass of the rack= 20 kgP=200Ninitial…

Q: The illustrated truss is subject to certain loads. Calculate the forces acting in the components…

A: The load at 1 and 7 = 0.8 kipThe load at 2,3,4,5,6 = 1.6 kip

Q: Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear…

A:

Q: The minimum required length of a key for a gear carrying 20000 lb.in of torque if it is mounted on a…

A:

Q: for example is a bridge that is supported on the left by a spring and damping while the right is…

A: Given:To find:Free body diagramNatural frequencyMode shape

Q: A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The…

A:

Q: 04: A Pelton wheel has a tangential velocity of bucket of (20 m/s). The water is being supplied…

A:

Q: The pressure loss through the pipe and the minimum power required to overcome the resistance to…

A:

Q: Water enters a steam boiler at 10 bar pressure, 80°C temperature and 4 kg/s mass flow and leaves the…

A:

Q: The semi-circular plate in Fig. Q3 is 4 m long and acts as a gate in a channel. Determine the…

A: Hydrostatic force on the semi-circular plate is given as:and

Q: Q1. A screw jack with a 1-in. double-thread Acme screw is used to raise a load of 4000 N. A plain…

A: According to the standard size of power screw threads, for an Acme screw with major diameter=1in.,…

Q: Two horizontal slabs measuring 0.8 x 1 m form the top of one of the slabs. The gap between them is…

A:

Q: The minimum required length for this key is most likely:

A: Diameter d = 1.5 inTorque T = 3000 lbMaterial of key SAE 1045Width W = 0.375 in for shaft diameter…

Q: A beam with a square section of 70 mm x 70 mm carries a single force of P = 4 kN as shown in the…

A:

Q: 02 Q Similarly, there is oxygen gas (02) in the piston-cylinder assembly at a volume of 0.4m^3…

A: Initial condition -Final Condition-T2 = 97o C= 370 K

Q: A skier is pulled by a rope exerting a horizontal force T=[T] KN at a distance h= [h] cm above the…

A: Given:To find:Critical load T

Q: For a finite wing, the three main contributions to the total drag force are skin friction drag…

A: For a finite wing, there are three main contributor to the total drag force are skin fraction drag,…

Q: The bar is supported by the thrust bearing A and the cable BC as shown in (Figure 1). Suppose that F…

A: We need to findReaction at point A

Q: If block A is moving downward at 6 ft/s while block C is moving down at 18 ft/s, determine the speed…

A:

Q: Consider 5.2 pounds per minute of water vapor at 100 lbf/in², 500°F, and a velocity of 100 ft/s…

A: Given:The mass flow rate is The pressure at entry is .The temperature is .The velocity is .The…

Q: Draw the aligned sectional view of the following solid

A: According to the given data, there are two projection views. We need to find The sectional view as…

Q: The 2 kg C cuff can slide freely along the straight AB shaft. Determine the acceleration of the C…

A: The mass of the c cuffAngle made by shaft AB with the vertical

Q: > two plates each with thickness t = 16 mm are bolted together with 6-22 mndia. bolts farming alap…

A: S1 = 40mm S2= 80 mmS3 = 100 mmbold dia = 25 mmt= 16mmAssume , Fu=400 MPa. Allowablestress: Tensile…

Q: Learning Goal: To use the equilibrium equations to solve for unknown forces in a coplanar force…

A:

Q: two plates each with thickness t = 16 mm are bolted together with 6-22 mndia. bolts forming alap…

A: 1.The thickness of each plate, t = 16 mmThe spacing between bolts, S1 = 40 mm, S2 = 80 mm, and S3 =…

Q: 2. The circular shaft has fixed supports at both ends, points A and D. Determine the torque that…

A:

Q: A 0.4 kg rubber ball has a horizontal velocity of 1.554 m/s at point A and goes through a projectile…

A: According to the given dataWe need to findThe velocity of the ball when hits the ground

Q: *1-44. The joint is subjected to the axial member force of 27 kN. Determine the average normal…

A:

Q: Question: A barrier gate was hit ba a car and deflected as shown in the figure. Treat the barrier…

A: For the solution refer below images.

Q: Convert to the units shown. 90.6 cm = in.

A: Given: Length: 90.6 cmTo find: Length in inches

Q: Using a diagram of “Head” vs “Discharge” discuss the key aspects that need to be considered for the…

A: Head: In hydraulic systems, the term head refers to the energy per unit weight of fluid. It…

Q: power (N)=9.9kw Input speed (n1)=2350rpm Distance between centers (a)=168mm Total distance…

A: Find the power transmitted

Q: Consider 4.8 pounds per minute of water vapor at 100 lbf/in², 500°F, and a velocity of 100 ft/s…

A: We are given the following data for water entering a nozzle :From Superheated Water From Superheated…

Q: = Determine the magnitude of the equivalent force at point B. Take F₁ 120 lb, F3 = 70 lb, F4 = 40…

A:

Q: The pendulum consists of a 5-lb slender rod AB and a 10-lb wooden block. A projectile weighing 0.28…

A: The angular velocity of the pendulum.Given:The mass of the projectile is .The mass of the block is…

Basic Thermodynamic Processes

The word 'thermodynamics' can be divided into two words, 'thermo' and 'dynamics'. The word thermo deals with the heat and thermal phenomenon, whereas dynamics deals with forces or external agent that drives the heat flow or aids in the motion of heat.