As shown in the image below, 10 µl of a stock solution (tube #1) are serially diluted into 0.990 ml of buffer. a. What is the dilution factor for this serial dilution? b. If the concentration of the stock solution in tube #1 is 0.8 M, what is the concentration of the solution in tube #3? 10 ul 10 l 10 l 0.990 ml 0.990 ml SM buffer 0.990 ml SM buffer SM buffer Tube #1 tube #2 tube #3 tube #4

As shown in the image below, 10 µl of a stock solution (tube #1) are serially diluted into 0.990 ml of buffer. a. What is the dilution factor for this serial dilution? b. If the concentration of the stock solution in tube #1 is 0.8 M, what is the concentration of the solution in tube #3? 10 ul 10 l 10 l 0.990 ml 0.990 ml SM buffer 0.990 ml SM buffer SM buffer Tube #1 tube #2 tube #3 tube #4

Curren'S Math For Meds: Dosages & Sol

11th Edition

ISBN:9781305143531

Author:CURREN

Publisher:CURREN

Chapter9: Parenteral Medication Labels And Dosage Calculation

Section: Chapter Questions

Problem 1.2P

See similar textbooks

Similar questions

. How much patient serum is needed to make a 1 mL 1:25 dilution? b. If a test procedure requires that the patient serum be diluted with 7 parts of distilled water, how much diluent should be used if the required serum volume is 250 µL? What is the final volume and dilution factor of the solution? c. How much NaCl in grams and distilled water is needed to make 10 mL of 0.9% NaCl solution? d. What is the final dilution factor of a solution if 500 µL serum is diluted with 9.5 mL of distilled water?
You have a 6 M solution of stock A. You do the following serial dilutions: Add 1 ml of stock A to tube B. Add 9 ml H2O. Mix.Then take 1 ml from tube B and put it into tube C. Add 19 ml H2O. Mix. Then put 5 ml from tube C into tube D. Add 5 ml H2O. A. what is the final (cumulative) dilution of stock A (dilution factor)? B. What is the final concentration (include units) after all these dilutions?
A.How much of 10,000x SYBR safe would you add to 50 ml to make a final concentration of 1x? B.How will you set up the serial dilution? How many tubes do you need? What is the concentration in each? How much LB will you add to each tube? What volume of cells will you add?
How do you calculate the initial concentration of a sample? How would you make a 1:10 dilution of a broth culture if the final volume of the dilution is 10 ml? How much broth, and how much diluent, would you add? If you made a series of tenfold dilutions, exactly the same way as you described in question 1, what would be the dilution factor in the fifth tube? The following are errors that people commonly make when they perform serial dilutions. Indicate whether you think that the number of cfu/ ml calculated would be too high or too low if you make this mistake. You intend to add 0.9 ml of diluent to each tube and 0.1 ml of culture. Instead, you add 0.5 ml of diluent to each tube and 0.1 ml of culture to the first tube. Then, you make a serial dilution of 0.1 ml into and from each tube as described. You prepare 0.9 ml of diluents in each tube. You add 0.1 ml of culture (from the overnight culture provided) to every tube. You add 0.9 ml of diluent to each tube. You add 0.1 ml of…
How would you perform a 100-fold dilution, if you want the final volume to be 15mL? What volume of sample and volume of dilute would be used?
In the spread plate method, why is the volume plated usually limited to not more than 0.1 mL?
Using a P-1000 micropipette, you transfer 800 microliter of ddH2O to a beaker and measure its weight. It turns out to be only 780 milligram; what is the percent error of this micropipette?
4 mL of 10% TCA solution was added to 1 mL of serum and after mixing, it was waited for two minutes and filtered through non-phosphorus filter paper. 1 mL of the filtrate was taken and 13 mL of distilled water, 4 mL of sulfomolybdic acid and 2 mL of dilute SnCl2 solution were added and mixed, and after waiting for 15 minutes, the absorbances of the obtained solutions against pure water at 520 nm were read. If the function of the calibration graph obtained with 0.5-2.5 mg/mL standard phosphorus solutions is y= 0.245x + 0.107 and the absorbance value of the serum sample is 0.109, what is the amount of phosphorus in the sample?
How would you make two-fold serial dilutions such that the last tube is a 1:32 dilution of the original, concentrated material? Assume that you need to have at least 500 µl of each dilution, and you should be able to perform the dilutions in microfuge tubes with a maximum capacity of 1.5 ml.
You record the absorbance of your unknown BSA sample at 0.276. What is the concentration in ug/mL of the unknown assuming you have a standard curve with the line of best fit with y=0.0001x+0.0038 as its equation
Refer to the chromatograph (Figure 1) below and answer the questions that follow: What is the volumetric flow rate of the column? What type of compound is likely to be found in peak B? Explain. What possible buffer changes could the researcher have applied at the 30ml mark? Explain. How would one avoid cross-contamination when using this type of purification
explain what the results of this experiment are and the purpose Table 2 Absorbance vs CoCl2 concentration Test Tube Number Cobalt Chloride Concentration (mol/mL) Absorbance at 510 nm 1 0.000 0.000 2 0.009 0.024 3 0.018 0.055 4 0.027 0.085 5 6 0.036 0.045 0.112 0.138 7 (Unknown) 0.088