bäi The command using to insert :seal is

Q: travelling ke to stop with W1 WI ning

A:

Q: Q2.Write Types of Key and Explain in detail with Diagram.

A: key A key is a machine element which is used in between shaft and hub or Boss of the pulley to…

Q: It asks what is the width across the flats of the locking bolt head?

A: The width across the flats of the locking bolt head is 0.5625

Q: g two (2) cylincer types:

A: 1. SINGLE ACTING CYLINDER 2.DOUBLE ACTING CYLINDER

Q: the block A vertical

A:

Q: minimum cllowasle deign dianet

A: Given; A solid circular shaft needs to be designed to transmit;Torque,T=50 N-mAllowable shear…

Q: Solid pattern can be used for making Ship engine blocks Select one: O True O False

A: Solution:

Q: ite a for loop to print all even numbers betw . Repeat with a while loop. . Write a for loop which…

A: 14. For loop to print even numbers b/w 1 to 20For m=1:20If (mode(m,2))=0display(m)endend15. Repeat…

Q: 2. Draw the positional sketch for excavator and also label all the symbols in the hy

A: The Hydraulic circuit for the excavator earth moving equipment is:-

Q: please explain for c) what is Sum of M at hinge

A:

Q: Chuck key requires lubrication maintenance. Select one: True False

A: A chuck key, sometimes known as a chuck wrench, is a tool used to tighten or loosen the jaws of a…

Q: er notation from the options provided. [Select] ed to be on top of each number. [Select] J Nim -IN…

A:

Q: Qin > Qout in (mark all that apply):

A:

Q: True or False: The BREAK command requires two separate points when breaking a circle.

A: The BREAK command is used to break the selected object between two points.

Q: 5. Name a tool that can be used to check an internal thread.

A: In this problem, it is asking about the name of the tool that can be used to check an internal…

Q: Select deep-groove

A:

Q: In a tap set, a plug tap is used for final cutting the thread throughout its length after using two…

A: Solution:

Q: a-) What is konck? Describe the Knock mechanism formed in the cylinder by drawing a figure. What is…

A: Knocking is the phenomena commonly occurring in a CI engine. You may know that in a CI engine the…

Q: ism to push a box, as shown below

A: Motor specification'   Torque  - τ = 85Nm r= 25m   (b) we know that  τ = F*r = Fr sin θ  = Fr F = τ…

Q: The tool used for marking center is __________. a.   Steel rule   b.   Divider   c.…

A: Solution:

Q: ged at D and E.

A:

Q: can you draw the FBD

A: There are four rivets in this problem. In ideal case load will be equally distributed. Each rivet…

Q: Which key is used to find a word in the ?document Ctrl +A O Ctrl +N None of these Ctrl + FO

A:

Q: an der Waal for I cross links.

A: In the above question all the options are incorrect Stiffness of thermosets are high

Q: Salve for CD HD and HG 4K CO H. TO 10 pick a jection ot cut ide and solve.

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: nance pr Tollowed wniie performing gib adjustment on a lathe machine is O On the front face of the…

A:

Q: A Before Ater False True O

A: Suppose Mass of Ball (A) = Ma                  Mass of Ball (B) = Mb  Initial velocity of mass A is…

Q: Respond with TRUE if the symbol of the valve shown below is diawn correctly. Select one: O True…

A:

Q: In a tap set, an intermediate tap is used to start a thread form in a drilled hole Select one: O…

A: The given statement is true.

Q: with proper value

A:

Q: the ctrocc con strocC con

A: The effect of stress concentration factor under static loading is not serious for ductile materials…

Q: esign the additional comp-

A: Required which design is used components in series and parallel

Q: While Drilling it is permissible to leave the check key in check while drilling a hole.

A: While Drilling it is permissible to leave the check key in check while drilling a hole. Answer:…

Q: List down any four safety precaution need to carry during the operation of Lathe machine.

A: Some safety precautions that need to be followed during the operation of Lathe machines are as…

Q: where is starting point

A:

Q: volume of metal

A: Given; While cooling a cubical catsing of side, 40 mmVolume shrinkage=3%, 4% and 5%  liquid state…

Q: What does a milky coloured ATF indicate

A: ATF in cars is stand for automatic transmission fluid. When a radiator fails, then the contaminated…

Q: What is the shortcut key for "Find and ?Replace" dialog box + Ctrl + Shift + FO Ctrl + RO Ctrl + FO…

A: Correct answer: Ctrl + H

Q: Chuck key requires lubrication maintenance. Select one: True False

A:

Q: drum of radiu ne left with a co

A:

Q: employ a pointer moving over a fixed scale.

A: The correct answer for this question is  Indicator employs a pointer moving over fixed scale

Q: haft G-Codes programming process (sumerik)

A: CNC programmers increasingly face special tasks that take them to the limits of classic (DIN 66025)…

Q: Write "open" or "closed" in the blanks below: When cylinder 1 is moving, check valve 1 is When…

A: When cylinder 1 is moving, check vale 1 is open. When cylinder 1 is moving, pressure control valve 1…

Q: extracting IC

A:

Q: machine operated for e ted at A and B. The sha ad on the shaft is indica e following:

A: n=475rpmL10h=25000hrsRelaibility goal =95% To-Find:- 1 Multiple of rating life required2 Catalogue…

Q: figures sho ed to a con Mat the free

A:

Q: attachment is reguired in shaner?

A: Shaper Machine

Q: Q1. Explain about Key and add a note on its use.

A: Dear student,                     According to the guidelines I am allowed to answer only one…

Q: The copper head hammer is used for releasing hold pin in the chuck. Select one: True False

A: The copper hear hammer is a hammer in which striking portion of the hammer (or head) are…

Die Stock

Die stock is expressed as the type of component which is utilized for fitting purposes while creating or shaping uniform threads on tubes, pipes, or screws. The die stock (die handle) has three screws around the adjustable part of a particular machine that helps to locate the die. Also, die stock can endure on a variety of hex and split adjustable dies of several dimensions. One of the primary reasons for using die stock in industries is because die stock can be operated by hands. Commonly, it is made up of high carbon steel.