In a tap set, an intermediate tap is used to start a thread form in a drilled hole Select one: O True O False

Q: In Drilling machine, Feed given to drill in this direction makes the hole Select one: a. Downward b.…

A: Given :-  In Drilling machine, Feed given to drill in this direction makes the hole Select one: a.…

Q: Advantage of taper turning by tail stock set over method is that power feed can be used. Select one:…

A:

Q: In a tap set, an intermediate tap is used to start a thread form in a drilled hole Select one: True…

A: In a tap set, an intermediate tap is used to start a thread form in a drilled hole

Q: 34. The operation of removing material from the end face of a round shaft is .ROwww Select one:…

A: Facing is the process of removing metal from the end of a workpiece to produce a flat surface

Q: Disadvantage of taper turning by tail stock set over method is that Lengthy tapers cannot be…

A: Tailstock set over method for taper turning – In this process the job is kept at an angle and the…

Q: The major diameter of a thread is defined as what

A: A thread is a bank of the constant section in the form of a helix on the internal or external…

Q: The following tool is used to cutting internal threads of drilled hole Select one: a. Drill plate b.…

A: It is required to which tool is used to cutting internal thread of drilled hole

Q: QUESTION 2 If you have to precisely rotate your workpiece, which is held on an indexing head, by a…

A:

Q: v thread is:

A: In screw largest diameter is its major diameter

Q: In a tap set, a taper tap is used to start a thread form in a drilled hole Select one: True False

A: Hand Taps (Configurations): Tap is a tool which can be used to provide an internal threads inside a…

Q: - Formula for finding the correct tap drill size. o for English system o for Metric system - Cutting…

A: Please find the solution below

Q: In a lathe machine tool, when the cutting tool moves perpendicular to the axis of rotation of the…

A: The given statement is ,

Q: Procedure: • Create a detailed thread drawing for the fastener given below. • Save your drawing to a…

A: Kindly refer the next page to see the detailed drawing.

Q: In a lathe machine tool, when the cutting tool moves parallel to the axis of rotation of the…

A: It is required to justify given statement

Q: Q3: Mark the Following True or False 1. Hatching of different components is done on same direction.…

A: 1. Hatching of similar components is done on same direction.     Hatching of different components is…

Q: True or False: The BREAK command requires two separate points when breaking a circle.

A: The BREAK command is used to break the selected object between two points.

Q: Lathe Machine tool is an example of three axes machines Select one: True False

A: The lathe machine tool axis - The cross slide (or turret) motion at a right angle to the spindle is…

Q: 5. Name a tool that can be used to check an internal thread.

A: In this problem, it is asking about the name of the tool that can be used to check an internal…

Q: Which of the following is the correct order of doing a fitting Job C. Marking -Filing - Surface…

A: First step of fitting job is marking then we can clamp the object in the vice so that material…

Q: in single-start, double-start and triple start thread with the help of diagrams

A: given: Explain single-start, double-start and triple start thread with the help of diagrams

Q: Q3: Mark the Following True or False 1. Hatching of different components is done on same direction.…

A:

Q: The threads formed on the the threaded rod of screw jack is based on inclined plane principle…

A: Incline plane is used in the machine to raise a heavy load . Generally, it requires more effort to…

Q: Shaper machine uses single point cutting tool for cutting mater Select one: True False

A: 1.true

Q: In a tap set, a plug tap is used for final cutting the thread throughout its length after using two…

A: Solution:

Q: Bolts and nuts are used for joining process. Select one: True False

A: Metal joining is defined as joining of two metal parts either temporarily or permanently with or…

Q: Write 10 steps of the Procedure for internal thread cutting

A: 1) Hole is first bored to the root diameter of the thread. 2) Tool is fixed on the tool post or on…

Q: 46. During the drill operations, the work piece and drill bit make an angle of 450. Select one: O…

A: Drilling is a cutting operation which uses drill bit to cut a circular hole in solid materials.

Q: The neutral point in a drill string can be defined as the point where the string changes from…

A: Answer is true. The neutral point in a drill is the point where there are neither compressive or…

Q: Advantage of taper turning by  tail stock  set over method  is that power feed can be used. Select…

A: Let us discuss about tailstock offset method.

Q: Main advantage of the Forming taps is:         a/ Evacuates the chips along the shank (for blind…

A: Option b is correct.

Q: In a tap set, an intermediate tap is used to start a thread form in a drilled hole Select one: True…

A: Intermediate or second or plug tap has tapered edges, which assists in aligning and starting the tap…

Q: In drilling operations, drill chucks are used for holding the work piece. Select one: True False

A: The above statement is false

Q: Lathe Machine tool is an example of two axes machines Select one: True False

A: The lathe machine tool is given

Q: Facing is an operation to reduce the diameter of work piece. Select one: True False

A: False

Q: 18 Which of the following are types of thread-cutting dies? Multiple Answer (check all that apply) O…

A:

Q: Cross slide is actively used during ___________machining operation on lathe. a. Drilling b. Turning…

A: Answer: Turning

Q: where is starting point

A:

Q: identify each if it is operated by a MAN or MACHINE i. Carry bar stock from the store. 1 min ii.…

A: (1) Carry bar stock from the store. 1 min  To carry stock from the store machines are used. (2) To…

Q: Advantage of taper turning by tail stock set over method is that power feed can be used. Select one:…

A: Objective: To determine the advantage of taper turning by tailstock set over method.

Q: 1. Name some uses of threads. Give an example of each.

A:

Q: In a tap set, a plug tap is used for final cutting the thread throughout its length after using two…

A: Generally there are three taps, Taper tap Plug tap Bottoming tap

Q: When a threaded system winds, in a clockwise direction when seen axially is known as .. thread *…

A: A screw thread is a helical structure used to transition between rotational and linear movement or…

Q: ) Down milling operation is performed for finishing cut. Select one: True False

A: Down milling is fed in the direction of the rotation

Q: Applying finger pressure on the belt near the pulley end is the correct method to check the tension…

A:

Q: Marking tool. 10. The manufacturing process shown in the figure below is calledt a. Turning process.…

A:

Q: With respect to a fitting operation, which of the following is the correct sequence of events? O A.…

A: The sequence of events in the fitting operation are first measurement is done to find the dimensions…

Q: Identify the part of a lathe machine which is mainly used to cut external threads.  Head stock…

A: External threads can be manufactured by using different methods such as thread cutting, thread…

Q: has 55° thread angle and both the crest and root are roundef off. a. ACME thread O b. V thregd

A:

Strain energy

The term strain indicates the variation in an object's length, area, and volume when the object is subjected to an external force. The external force may be of normal, shear, moment, torque, etc. The strain in an object depends on the types of external force and cross-section of the object. Mathematically, the evaluation of strain can be obtained with the help of elastic constants.