calculate, the number of bits required for 8 quantization levels, quantization step size and level values when the input signal to the quantizer has peak to peak values of (-2,3).
Q: 3. Describe the fundamentals of the use in the pn junction diode, LED and resistor in each of the…
A: OR gate using PN diodes A B LFO 0 0 OFF 1 1 ON 0 1 ON 1 1 ON
Q: What is edge triggering?
A: Triggering of a circuit is referred to the enabling of circuit working. When the circuit is…
Q: Q6: How many bits are represented by each symbol in 64-QAM? Sketch a constellation diagram for 64-…
A: We are authorized to answer one question at a time, since you have not mentioned which question you…
Q: What will be the binary equivalent of hexadecimal number EB?
A: Hexadecimal number system has a base of 16 that is there are 16 unique digits are there in this…
Q: Design a combinational circuit that takes 3-bit pattern as input and outputs binary code of bit…
A: Truth table is, a b c A B V 0 0 0 X X 0 0 0 1 0 0 1 0 1 0 0 1 1 0 1 1 0 1 1 1 0 0 1 0 1…
Q: If in a PCM system, uniform quantizer having total 256 steps is being used, then what will be the…
A: Given information: The number is steps present in the uniform quantizer is L=256
Q: Determine the signal to quantization noise ratio for a 6 bit PCM.
A: Quantization Noise: The sampled signal with quantization error is the decoder output in a PCM…
Q: What are the functions of encoder, Decoder, multiplexers explain with truth table and give…
A: Encoder It is a circuit that is used to convert the given data from one format to another. In this…
Q: A sinusoidal massage signal m(t) is transmitted by binary PCM without compression. If the signal to…
A: Given information: The value of the signal to quantization noise ratio is SNQ≥48 dB.
Q: Q3:/ consider the following analog waveform. This waveform is sampled at a 500 Hz rate and quantized…
A: First find out the quantization level in above question and then find out the sampling points :-…
Q: Q3: Explain with aid of figures and equations the type of quantization and the quantization error.…
A: The quantization is a process of converting an analog signal into an equivalent digital signal. This…
Q: Derive the equation for probability of bit error in a binary PAM system using the simple PAM…
A: According to the question, we need to derive the equation for the probability of bit error in the…
Q: Q5/ The information in an analog waveform with maximum frequency fm = 3 KHz is to be transmitted…
A:
Q: Q| Write an 8086 assembly language program to multiply the contents of the registers CL & BL by…
A: Since content of register are given in register BL and register CL which are 8 bit in length so it…
Q: Binary 4-bit Asynchronous down Counter and explain how it functions, find real life applications
A: The digital circuits can be combinational as well as sequential circuits. The combinational circuits…
Q: The circuit that converts continuous signal into 'n' bit binary number is called as ___________.…
A: Given To determine which circuit converts continuous signal into n bit binary number
Q: Given the quantization levels in the following figure, write down the PCM output levels (for t-0-4…
A: Given: The quantization levels in the following figure is shown below: Sign bits: + is 0, - is 1.…
Q: What should be the value of the LCDM10 register (in hexadecimal format), if the A1 alphanumeric…
A: That is the embedded system.here we Directly write the value of LCDM10 register if number 6. Below…
Q: Consider sampling (quantizing, digitizing) analog temperatures in the range from -17 to 17 °F. How…
A: Given, Sampling analog temperature in the range from -17 ° F to 17° F. The smallest difference…
Q: Design a binary counter with the following binary sequence: 2,0,1,0,1,2,1,1,2 and repeat. Use D…
A: Given: Binary counter. Sequence: 2,0,1,0,1,2,1,1,2 and repeat. D flip flop.
Q: ethe base of the number for the following operation to be c 25 26 - 23 9. e 8-bit binary number…
A:
Q: Design a State Diagram and State Table for the following 8 bit secret code: 10100110
A: Since the code is of length 8-bit, hence, it requires 3 Flip Flops. Let the input is X and the…
Q: QI/ show how an asynchronous counter can be implemented having modulus fifteen with a stright binary…
A: As per our company guidelines we are supposed to answer only first question kindly repost other…
Q: if a QAM modulated signal is Q mtlcoswet+mSincwet and Find out the massage signal.
A: In ϕQAM modulation, we can modulate the two individual message signals with the single carrier…
Q: A frequency counter is gated on for 10 ms and counts 540 pulses from a periodic input signal . What…
A: Frequency counter is an electronic device used to measure frequency of a signal. Counter in the…
Q: The resolution of the ADC unit with the reference voltage value of 3V is set to 8 bits. If the…
A: Consider the given data: The input is 1.67 V The bit is 8 The reference voltage is 3 V
Q: A digital circuit whose number of inputs is 3, how many possible combinations of inputs will it…
A: In this question , we will find possible combinations of input if number of input is 3....
Q: Q.6 Describe the operation of a basic parity generating and checking logic.
A: In digital systems, the parity generator is a combinational logic circuit. this logic circuit is…
Q: Analyzed the modifications required for the input functions to transform the 4-bit binary ripple…
A: Given: Brief description: In the above given question they have mentioned designing of a BCD ripple…
Q: Derive the State table using binary numbers
A: Given state table in decimal form
Q: Design a full digital circuit diagram with a control line for a system to transfer data between two…
A: For the full digital circuit, the clock signal (CLK) is required. Here, 6 control signals are taken:…
Q: The dynamic range of PCM is equivalent to the following; a. Number of levels -1 O b. Number of bits…
A: Dynamic range of pcm is equivalent to 2^n -1 The possible number of levels are 2^n n is no of…
Q: Q4) Starting from an initial value of R 11010101, determine the sequence of binary values in R after…
A: circular shift does not change the value of R . first we shift R logic left then in last logic right…
Q: Design a 4-bit magnitude comparators, which compares two 4-bits binary numbers (A3A2A1A0 and…
A: binary inputs A3 A2 A1 A0 Binary inputs B3 B2 B1 B0 Outputs A<BA>BA=B
Q: Let the data stream 1001011101 to be the input sequence of a differential encoder. Assume that the…
A: Given: The data stream 1001011101 to be the input sequence of a differential encoder. Assume that…
Q: iii) An analogue signal carries 64 bits per level. If 2000 levels are sent per second, find the bit…
A: Given: n=64 bits per level and 2000 levels per second
Q: Q1: Plot the output signal for DSSS when user data = 0101110110001011, and chipping sequence %3D %3D…
A: Given A data signal and chipping sequence. We need to obtain DSSS signal Please find the below…
Q: Explain the Analog to digital conversion in digital signal processing with each step elaborated
A: There are three main things involved in ADC conversion process. First sampled the signal and then…
Q: Q.1: What is Quadrature Amplitude Shift Keying (QAM)? Explain with geometrically for symbol…
A: This scheme is called as M-ary QAM (where M= Number of symbols/messages and n=log2M is the number of…
Q: Design a system called a parallel binary comparator, that compares the 4 – bit binary string A to…
A: Design a system called a parallel binary comparator, that compares the 4 – bit binary string A to…
Q: Draw the Moore and Mealy State Diagram of a Finite State Machine that functions as a Binary Sequence…
A: Draw the Moore and Mealy State Diagram of a Finite State Machine thatfunctions as a Binary Sequence…
Q: How to represent a priority encoder by using truth table and draw a diagram
A: The binary encoder is used to compress a large number of the inputs to a smaller output. For…
Q: one method of eliminating contact bounce wherein it triggers on the first contact bounce instead of…
A: To select proper answers from options.
Q: In the figure below, the ADC size (N bits) in order to deliver an output signal with less than 2.5…
A: The solution can be achieved as follows.
Q: An analog signal having a maximum frequency of 10 kHz is being transmitted through a PCM system with…
A: If the maximum frequency component present in the analog signal if fm Hz, then the minimum…
Q: Find the number of bits given if the PCM system has a quantization error of 0.4 V and maximum input…
A: Given: Quantization error = 0.4 V Maximum input = 6V
calculate, the number of bits required for 8 quantization levels, quantization step size and level values when the input signal to the quantizer has peak to peak values of (-2,3).
Step by step
Solved in 2 steps with 1 images
- Determine the signal to quantization noise ratio for a 6 bit PCM.Discuss the effect of changing the number of bits on the recovered analog waveformThe current output of a successive approximative type ADC is showing as 110011. If the reference voltage to the ADC is 5V, what is the corresponding analog signal voltage input to this ADC? If the ADC were of 10 bits, would the conversion time be reduced? Please answer ASAP I will like it please ASAP...
- please show work included 4. If a 6-bit binary number is used to represent an analog value in the range from -63 to 126, what is the accuracy of the system? In other words, if the binary number is incremented by one, how much change does it represent in the analog value?Qَ\ discuss a conversion of an analogue signal to digital bits Please I need to resolve the question quicklyDetail 2-bit quantization ?
- An analog signal having a maximum frequency of 10 kHz is being transmitted through a PCM system with a uniform quantizer having 256 levels. What will be the minimum transmission bandwidth of the transmitted PCM signal?In an adder circuit in which two numbers of two bits are added together, what will be the output signal values at the last hand when the inputs are given as follows?What is the maximum quantization error of an ideal 4-bit quantizer with a signed input signal having amplitude ±6? Answer should be with 4 decimal places.
- What will be the binary equivalent of hexadecimal number EB?S Display will be designed for a thermometer. The display will show that degree for minimum temperature and 99 degrees for maximum temperature. According to this; a) What is the number of bits that will be needed in the binary code to express the temperature? b) What are the binary, octal and hexadecimal equivalents of 95 degrees? () What is the BCD representation of 95 degrees? d) What is the hex equivalent of this temperature when it shows 111 degrees octal? e) If the thermometer showed a temperature between -99 and +99 degrees, how many bits would we need?What is edge triggering?