Date Name Industry Print Exercise 14-1 Refer to the print PR 14-1 and answer the questions below. 1. How many columns are featured in the revision history block of this drawing? 2. What is the current revision letter assigned to this part? 3. What revision specified the surface texture of the tapered portion? 4. What are the initials of the person who implemented or approved ECO 68-557? 5. Which revision specified the vendor part number of the bushing? 6. Revision F changed the maximum axial deflection to .500 at 2000 pounds. What had it been? 7. Instead of revision D, E, and F being three letters, what other method of marking could have been implemented for these three changes? Review questions based on previous units: 8. What is the thread form specified for the internal threaded holes? 9. What method was used to show external threads on this part? 10. Is this a drawing of multiple parts assembled? 11. Does this drawing feature any cutting-plane lines? 12. What is the radius of the undercut indicated by a local note? 13. What is the maximum material condition diameter of the largest cylindrical feature of this part? 14. This drawing has an italic "f" symbol on some surfaces in the left side view. What are these symbols? 15. What does the 125 near the check mark at revision A on the tapered surface mean? Inc. Unit 14 Drawing Revision Systems 299 14 Print supplied by Clark Equipment Company PR 14-1. ASM Silent Block Axle Mounting 4.68 4.62 2.510. 2.490 2.510 2.490 1.042 1.022 1.010 2.312 2.252 0 -1 t.020 " B" -12 TAPER PER FOOT GRIND OR MACHINE OPT.A MIN. FLAT .75 BOTH ENDS DDRILL X 45 CHAMFER 32 HOLE tMUST .28 RWT BOTH ENDS. BE 90 t.010 WITH MOUNTING BOSSES A 125 2.68+.09 000 5.50 (2.18) (1.62) (1.41) 1.005 1.262 1.259 4.26 4.24 1722071 .09 X 45 CHAMA 2.12 -0.50 DRILL V.50 FOR ASM OPT. CONST. 1-12 UNF-2A, PD .92 .020 THD LENGTH (A MAX. 1.0691 MIN. 1.0631 "A" A - R MUST BE FREE OF TOOL MARKS -SAE-R630 BHK,Z D OR SAE-R630 BHZ A Z-DENOTESA HIGH MODULUS STOCK E WITH WEATHER RESISTANCE AND RESISTANCE TO A HYSTERESIS BUILD UP SAE 4140 LEADED C.R. OR STRESSPROOF .62 MALLEABLE IRON SAE 32510 A DUCTILE 60-45-10 OPT. +.88 -1.75- 18 UNF-3B, PD V.03 X 30 2 HOLES MAX. .5934 MIN. .5889 NOTE SURFACES "A" & "B" AND "C" & "D" MUST BE PARALLEL AND IN SAME PLANE DEFLECTION SPEC.: MAX. RADIAL DEFLECTION .050 AT 4000 POUNDS MAX. AXIAL DEFLECTION .500 AT 2000 POUNDS BREAK ALL SHARP CORNERS SIMILAR TO 329676 CHG. NO. MICRO UNLESS OTHERWISE SPECIFIED MAX. FILM OR 010 INDUSTRIAL TRUCK DIVISION CLARK EQUIPMENT CO. CHANGES DATE BY VENDORS DAYTON RUBBER CO BUSHINGS INC. NO. 3221 C TOL. ON FIN. DIMS ALL OTHER DIMENSIONS DO NOT SCALE SCALE MATERIAL BATTLE CREEK, MICHIGAN NOTED ASM SILENT BLOCK 20 JAN HT. TREATMENT WAS .250 Z NOTE ADDED D WAS SAE-R-630-BHKZ 23 DEC JCS CNO. ADDED WAS 1 MIN. THD A ADDED 16 JAN JCS AXLE MOUNTING 13 JAN JCS HARDNESS 20 THRU 50 M. BRESSON DATE DATE 12 APR DATE DATE DRAWN FOR 68-557 67-971 67-651 22 MAY DRAWN BY 16 OCT CHECKED BY 26 JUL RELEASED BY 16 MAY MB 1722071 11 OCT MB RN67-393

Question

I need answers for questions 10, 11, and 12.

Date
Name
Industry Print Exercise 14-1
Refer to the print PR 14-1 and answer the questions below.
1. How many columns are featured in the revision history block of this drawing?
2. What is the current revision letter assigned to this part?
3. What revision specified the surface texture of the tapered portion?
4. What are the initials of the person who implemented or approved ECO 68-557?
5. Which revision specified the vendor part number of the bushing?
6. Revision F changed the maximum axial deflection to .500 at 2000 pounds. What had it been?
7. Instead of revision D, E, and F being three letters, what other method of marking could have been
implemented for these three changes?
Review questions based on previous units:
8. What is the thread form specified for the internal threaded holes?
9. What method was used to show external threads on this part?
10. Is this a drawing of multiple parts assembled?
11. Does this drawing feature any cutting-plane lines?
12. What is the radius of the undercut indicated by a local note?
13. What is the maximum material condition diameter of the largest cylindrical feature of this part?
14. This drawing has an italic "f" symbol on some surfaces in the left side view. What are these symbols?
15. What does the 125 near the check mark at revision A on the tapered surface mean?
Inc.

Image Transcription

Date Name Industry Print Exercise 14-1 Refer to the print PR 14-1 and answer the questions below. 1. How many columns are featured in the revision history block of this drawing? 2. What is the current revision letter assigned to this part? 3. What revision specified the surface texture of the tapered portion? 4. What are the initials of the person who implemented or approved ECO 68-557? 5. Which revision specified the vendor part number of the bushing? 6. Revision F changed the maximum axial deflection to .500 at 2000 pounds. What had it been? 7. Instead of revision D, E, and F being three letters, what other method of marking could have been implemented for these three changes? Review questions based on previous units: 8. What is the thread form specified for the internal threaded holes? 9. What method was used to show external threads on this part? 10. Is this a drawing of multiple parts assembled? 11. Does this drawing feature any cutting-plane lines? 12. What is the radius of the undercut indicated by a local note? 13. What is the maximum material condition diameter of the largest cylindrical feature of this part? 14. This drawing has an italic "f" symbol on some surfaces in the left side view. What are these symbols? 15. What does the 125 near the check mark at revision A on the tapered surface mean? Inc.

Unit 14
Drawing Revision Systems
299
14
Print supplied by Clark Equipment Company
PR 14-1. ASM Silent Block Axle Mounting
4.68
4.62
2.510.
2.490
2.510
2.490
1.042
1.022
1.010
2.312
2.252
0
-1 t.020
" B"
-12 TAPER PER FOOT
GRIND OR MACHINE OPT.A
MIN. FLAT
.75 BOTH ENDS
DDRILL X 45 CHAMFER
32
HOLE tMUST
.28
RWT
BOTH ENDS.
BE 90 t.010 WITH MOUNTING
BOSSES
A
125
2.68+.09
000
5.50
(2.18) (1.62) (1.41) 1.005
1.262
1.259
4.26
4.24
1722071
.09 X 45 CHAMA
2.12
-0.50 DRILL
V.50 FOR ASM
OPT. CONST.
1-12 UNF-2A, PD
.92 .020 THD LENGTH (A
MAX. 1.0691
MIN. 1.0631
"A"
A
- R MUST BE FREE OF TOOL MARKS
-SAE-R630 BHK,Z D
OR SAE-R630 BHZ A
Z-DENOTESA HIGH MODULUS STOCK
E WITH WEATHER RESISTANCE AND
RESISTANCE TO A HYSTERESIS BUILD UP
SAE 4140 LEADED C.R.
OR STRESSPROOF
.62
MALLEABLE IRON SAE 32510
A DUCTILE 60-45-10 OPT.
+.88
-1.75-
18 UNF-3B, PD
V.03 X 30 2 HOLES
MAX. .5934
MIN. .5889
NOTE
SURFACES "A" & "B" AND "C" & "D" MUST
BE PARALLEL AND IN SAME PLANE
DEFLECTION SPEC.:
MAX. RADIAL DEFLECTION .050 AT 4000 POUNDS
MAX. AXIAL DEFLECTION .500 AT 2000 POUNDS
BREAK ALL SHARP CORNERS
SIMILAR TO 329676
CHG.
NO.
MICRO UNLESS OTHERWISE SPECIFIED MAX.
FILM
OR 010 INDUSTRIAL TRUCK DIVISION
CLARK EQUIPMENT CO.
CHANGES
DATE
BY
VENDORS
DAYTON RUBBER CO
BUSHINGS INC. NO. 3221 C
TOL. ON FIN. DIMS
ALL OTHER DIMENSIONS
DO NOT SCALE
SCALE
MATERIAL
BATTLE CREEK,
MICHIGAN
NOTED
ASM SILENT BLOCK
20 JAN HT. TREATMENT
WAS .250
Z NOTE ADDED
D WAS SAE-R-630-BHKZ 23 DEC JCS
CNO. ADDED
WAS 1 MIN. THD
A ADDED
16 JAN JCS
AXLE MOUNTING
13 JAN JCS
HARDNESS
20 THRU 50
M. BRESSON
DATE
DATE 12 APR
DATE
DATE
DRAWN FOR
68-557
67-971
67-651
22 MAY DRAWN BY
16 OCT CHECKED BY
26 JUL RELEASED BY
16 MAY MB
1722071
11 OCT MB
RN67-393

Image Transcription

Unit 14 Drawing Revision Systems 299 14 Print supplied by Clark Equipment Company PR 14-1. ASM Silent Block Axle Mounting 4.68 4.62 2.510. 2.490 2.510 2.490 1.042 1.022 1.010 2.312 2.252 0 -1 t.020 " B" -12 TAPER PER FOOT GRIND OR MACHINE OPT.A MIN. FLAT .75 BOTH ENDS DDRILL X 45 CHAMFER 32 HOLE tMUST .28 RWT BOTH ENDS. BE 90 t.010 WITH MOUNTING BOSSES A 125 2.68+.09 000 5.50 (2.18) (1.62) (1.41) 1.005 1.262 1.259 4.26 4.24 1722071 .09 X 45 CHAMA 2.12 -0.50 DRILL V.50 FOR ASM OPT. CONST. 1-12 UNF-2A, PD .92 .020 THD LENGTH (A MAX. 1.0691 MIN. 1.0631 "A" A - R MUST BE FREE OF TOOL MARKS -SAE-R630 BHK,Z D OR SAE-R630 BHZ A Z-DENOTESA HIGH MODULUS STOCK E WITH WEATHER RESISTANCE AND RESISTANCE TO A HYSTERESIS BUILD UP SAE 4140 LEADED C.R. OR STRESSPROOF .62 MALLEABLE IRON SAE 32510 A DUCTILE 60-45-10 OPT. +.88 -1.75- 18 UNF-3B, PD V.03 X 30 2 HOLES MAX. .5934 MIN. .5889 NOTE SURFACES "A" & "B" AND "C" & "D" MUST BE PARALLEL AND IN SAME PLANE DEFLECTION SPEC.: MAX. RADIAL DEFLECTION .050 AT 4000 POUNDS MAX. AXIAL DEFLECTION .500 AT 2000 POUNDS BREAK ALL SHARP CORNERS SIMILAR TO 329676 CHG. NO. MICRO UNLESS OTHERWISE SPECIFIED MAX. FILM OR 010 INDUSTRIAL TRUCK DIVISION CLARK EQUIPMENT CO. CHANGES DATE BY VENDORS DAYTON RUBBER CO BUSHINGS INC. NO. 3221 C TOL. ON FIN. DIMS ALL OTHER DIMENSIONS DO NOT SCALE SCALE MATERIAL BATTLE CREEK, MICHIGAN NOTED ASM SILENT BLOCK 20 JAN HT. TREATMENT WAS .250 Z NOTE ADDED D WAS SAE-R-630-BHKZ 23 DEC JCS CNO. ADDED WAS 1 MIN. THD A ADDED 16 JAN JCS AXLE MOUNTING 13 JAN JCS HARDNESS 20 THRU 50 M. BRESSON DATE DATE 12 APR DATE DATE DRAWN FOR 68-557 67-971 67-651 22 MAY DRAWN BY 16 OCT CHECKED BY 26 JUL RELEASED BY 16 MAY MB 1722071 11 OCT MB RN67-393

Expert Answer

1 Rating

Want to see the step-by-step answer?

Check out a sample Q&A here.

Want to see this answer and more?

Experts are waiting 24/7 to provide step-by-step solutions in as fast as 30 minutes!*

*Response times may vary by subject and question complexity. Median response time is 34 minutes for paid subscribers and may be longer for promotional offers.
Tagged in
Engineering
Mechanical Engineering

Related Mechanical Engineering Q&A

Find answers to questions asked by students like you.

Q: 1. Consider a flat plate solar collector placed horizontally on the flat roof of a house. The collec...

A: Given data,

Q: below attached image. fluid mechanic

A: The cardiologist wants to build a blood cell culture chamber. This means, it is to be kept at the st...

Q: The force that bonds together themolecules of unlike substances when thesurfaces come in contact is ...

A: When the two unlike substances come in contact with each other, the force that hold them together is...

Q: At the beginning of the compression process of an air standard Otto cycle, p1 = 1 bar, T1 = 300 K. T...

A: Hey, since there are multiple sub parts posted, we will answer first three sub parts. If you want an...

Q: Technician A says that the front bearing assembly locknuts for RWD vehicles are typically heavily to...

A: A high torque for maintaining the bearing adjustment is required in the FWD vehicles and not the RWD...

Q: the compound beam in the attachnent is fixed at A, pin connected at B, and supported by a roller at ...

A: Split the compound beam into simple beam as shown in figure.

Q: In figure below, water enters at point A and leaves at point C. The process is steady state. The atm...

A: Draw the free body diagram for the fluid and the pipe at joint A as:

Q: A resistance heater is placed inside a rigid insulated tank containing 0.25 kg of nitrogen for the p...

A: Mass of nitrogen in the tank = 0.25 kgThe value of current = 0.3 AmpsThe value of resistance of heat...

Q: per the attacment (zoom in when necessary): for the beam and the loading shown, draw the shear force...

A: The free body diagram of the beam is drawn as bellow,