Determine (a) the principal stresses and (b) themaximum in-plane shear stress and average normalstress. Specify the orientation of the element ineach case.Solve Part A and B above using both of thefollowing approaches:。 Using the equations discussed duringlecture• Using Mohr's Circle.Hint: Remember to sketch the results on a stresselement to communicate the orientation of theelement for Parts A & B.20 MPa40 MPa100 MPa

Step 1: Step 2: Step 3: Step 4: solution is given above

Answered: Determine (a) the principal stresses…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The state of plane stress at a point is represented on the element shown in the figure below. (a) Determine the principal stresses acting on this point, and the corresponding orientation (angle). (b) Determine the maximum in-plane shear stress, and the corresponding orientation (angle). Also determine the associated average normal stress. Draw Mohr's circle and show the stresses on the circle. 16 MPa 10 MPа
Problem 3: For the plane stress state listed below, draw a Mohr's circle diagram properly labeled. Keep in mind that the principal stress is that stress state where the shear stress is zero. That means it is the stress state along the normal stress line in Mohr's space. So, use your Mohr's circle to find the principal normal and shear stresses, and determine the angle from the x axis to o1. 0x = 16 kpsi, oy = 9 kpsi, Ty = 5 kpsi ccw
Determine the equivalent state of stress which represents the principal stresses, and the maximum in-plane shear stress and the associated average normal stress. For each case, determine the corresponding orientation of the element with respect to the element shown in the figure below. (Figure 1) Determine the orientation of principal planes of stress. Express your answers in degrees to three significant figures separated by a comma.
Question is in image
There are forces acting in the Z and Y directions 1000N and 1500N please post your own correct answer everyone keeps copy and pasting an incorrect answer that neglects the stress acting in the y axis
Fill in the blanks . Draw and label the Mohr’s circle. For sigma-yp = 15 ksf, does this fail? Find the stresses on the plane shown. Find the plane on which sigma-1 acts relative to the horizontal. Draw them on the figure. Draw the Tresca plot.
Consider a certain critical point in a stress element. On a vertical plane, the compressive stress is 115 MPa and the shear stress is 31.5 MPa. There is no normal stress on the horizontal plane. Find the stresses acting on the principal planes and the orientation of principal planes with the horizontal plane. You may need to draw a Mohr circle.
Determine the state of stress at point A of the rectangular post shown loaded with concentrated forces directed along the y axis equal to 75kN and along the x axis equal to 15kN. 1)Determine the total normal stress along the x and y axes at point A (include if tensile or compressive in your final solutions) 75 kN 50 mm 200 mm- 150 mm OAx= 15 kN OAy= 2) Draw the state of stress of point A 800 mm A 50 mm
Please solve all. Both Questions Please.
Determine the state of stress acting at point D. Take P₁ = 120 kN and P₂ = 45 kN. (Figure 1) Figure L -1.5m- +1.5m-1.5 m- 0.5 m 40 mm 100 mm 60 mm 80 mm 1 of 1 > Find op- Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. od= - 154.88 Submit Part B Previous Answers Request Answer X Incorrect; Try Again; 3 attempts remaining MPa Find TD- Express your answer to three significant figures and include the appropriate units. JA TD= Value Units ?
For the flat stress state shown in the figure. Use Mohr's circle to determine (show the procedure only with the use of geometry): a. Draw Mohr's circle indicating coordinates of the points that represent the given stress state, center, radius, coordinates of the points that represent the state the maximum and minimum normal stresses, coordinates of the maximum shear and angle of rotation from the stress given to the plane principal. b. Use the results of literal a to draw the element subjected to main forces and the element subjected to maximum shear. 12 MPa 19 MPа y 19 MPа 46 MPа 46 MPа 19 MPа 19 MPа 12 MPa
Note: Give me all right solutions with clear calculations

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS