Answered: Determine the deflection @ C using…

Determine the deflection @ C using Moment Area Method. (Your final answer should be in "mm") 8 kN/m 3 kN A C D 6 m 4 т 3 т E = 200 GPa %3D I = 260 x 106 mm4

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.6.5P: -5 Calen1ate the deflections S 3a nd

See similar textbooks

Related questions

Q: The vertical deflection at the free end of a stepped cantilever, subjected to moments (M = 10KN-m)…

A: In the given question,L=5+5 = 10 mM = 10 kN-m

Q: Q 4: Using Castigliano's method for Determining the vertical deflection at A for the lamp post…

A: NOTE:- here axial deflection in portion BC is very small so it is neglected. For solution refer…

Q: The simply supported beam consists of a W460 x 82 structural steel wide-flange shape [E = 200 GPa; I…

Q: The cantilever beam AB shown has a rigid bracket AC attached to its free end. Find the ratio a/L…

Q: BP1 A round steel beam with diameter d=1 cm and length L=1 m, supported at L/3 and 2L/3, is loaded…

A: Draw the free-body diagram of the beam.

Q: The link CE (Diameter D=12mm) and DF (Diameter D=10 mm) are connected to rigid link ABCD as shown in…

Q: Determine the internal moments at each joint using Slope-deflection equation method. El is constant.…

Q: 2. The simply supported beam shown in the figure consists of a W410x60 structural steel wide-flange…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: 3. A turbine shaft made from steel (E-200GPA) is exposed to a resulting load F=5417N. The supports…

Q: Q 04: A jib crane consists of a rigid beam BC supported by an elastic rod AB and hinged at C.…

Q: A SSB of 8 m span carries a point load of 10 kN at its centre. It also subjects to a UDL of 1 kN/m…

A: Given:Length of beam,L=8m=8×103mmPoint load,P=10KN=10×103N=104NUDL=1KNm=1×103N103mm=1NmmYoung's…

Q: For the beam shown; 1. Determine the equations of slope and deflection. 2. Determine the slope and…

Q: For the beams below, determine the location of the maximum deflection using double integration…

Q: The simply supported beam consists of a W460 x 82 structural steel wide-flange shape [E = 200 GPa; I…

A: The deflection at point C is vC = - 17.55 mm or 17.55 mm ↓.

Q: A composite simply supported beam of span 10m and carrying a point load of 800N at its mid- span, is…

Q: A spring wire with diameter of 6 mm in a circular arc shape was initially set on the horizontal…

A: Given values, Radius of the arc(R)=80mm, angle of arc(θ)=60 deg, Modulus of Elasticity(E)=200GPa,…

Q: 1.5 k/ft 30 k D. B 6 ft +4 ft- 5 ft- El E = 1,500 ksi I = 20,000 in.4 constant

A: to find- the slope at point B deflection at point C

Q: * A Given the FLEXURAL RIGIDITY of the beam shown=6000 KN.m^2, find the deflection at the roller…

Q: A W310 x 129 I-beam, made of A36 steel, is shown in the figure. This I-beam is 4 m long and has a…

Q: Q/ For the beam shown in the figure below, find deflection and rotation at point B. EI=12000 kN.m2.…

Q: Using any of the classical methods (Double-Integration or Area-Moment Method), identify the…

Q: b. Determine the deflection of the beam at midpoint for the beam loading system shown in the figure…

Q: Hw: Find te slope and deflection in the section (A-A) and the Section cB-B) for the beam Shown.…

A: Given Data: The uniform load is w= 2 kN/m. The span of the beam is L=4.5 m The value of E=205 GPa.…

Q: 2. By using Three Moment Equation, determine the deflection 3mto the left of roller support. 30 kN/m…

Q: Assume that El is constant for the beam. Let w = 9 kN/m, L = 5.0 m, E = 190 GPa, and I = 105 x 10°…

Q: e the elastic curve for the cantilevered n using the x coordinate. Specify the d maximum deflection.…

Q: c) Calculate the vertical deflection at Point B. d) Briefly describe how you would solve the…

A: In this problem, it is asking about the parts c and d.

Q: C) Ose Castigtion's theorm to find vertical deflection in pant ca) for the beam shown below,…

A: Given data: The modulus of elasticity is E=200 GPa=200×103 MPa The inertia of the beam is I=300×106…

Q: 7.24. Find the deflection at C; E = 200 × 106 kN/m², I of beam = 100 × 106 mmª, A of cable = 200…

Q: Determine the horizontal and vertical components of the deflection at joint B of the truss shown in…

A: Given Structure To find Deflection at point B, horizontal and vertical

Q: ..s) The beam shown is fixed at A and to be supported by rod BC at B. The beam carries a uniform…

A: we have to calculate the deflection without rod

Q: The steel (E 200 GPå, I = 351 x 10° mm*) beam shown below has a pin support at A, a roller support…

A: RA+RC=55×10=550 KWM=-(55×10×5)+(RC×7.2)=0Rc×7.2=2750RC=382 KN

Q: For The beam shown in The Figure belw. find deflection at point B FI =12000 KN wm? P= 50 KN M225KN.m…

Q: 04: For the beam shown in Fig. 4, determine the deflection at point D and indicate whether the…

Q: Using Castigliano's theorem, derive an expression of the bending deflection at point B. A |C |B L/2…

Q: ind the deflection at D relative to point A of the copper bar. Assume the material behaves…

A: Given:E=15*103ksi

Q: 4. The beam is made of a material having a specific weight y. Determine the displacement and slope…

A: Given: Specific weight of the material is γ. Modulus of elasticity of the material is 25 Gpa.…

Q: | 90 kN 190 kN D EV |B For the beam and loading shown, determine the deflection at S250 x 37.8 point…

Q: 12 kN 8 kN/m 50 kN-m A B -5 m 4 m-

A: Given Total length of beam L=5+4=9 m Uniform load of magnitude 8 kN/m acting over a span of 5 m from…

Q: ..s) The beam shown is fixed at A and to be supported by rod BC at B. The beam carries a uniform…

Q: P Ib w lb/ft w lb/ft B. - 6 ft- - 6 ft- 4 ft-

A: We calculate reaction at A and B first Sum of all forces in Y axis = 0 RA + RB -6 -6 -4= 0 RA + RB =…

Q: The beam shown is made from 6 × 6 × 1/4 inch rectangular steel structural tubing. If load P = 650 lb…

Q: and determine the max deflection and max bending stress E= 200 GPa 3 kN/m A B 10 m 20 m 21 c = 0,25…

Q: Find the deflection at the mid-point BC of the loaded beam as shown in the figure by the double…

Q: An 8 m simply supported beam has a uniform load of 2 KN/m from left end to right end and…

Q: 2. For the shaft shown below, having diameter 30 mm and mass density 7700 kg/m³, (1) (ii) (iii)…

Q: For the beam shown below, B L- t-1/2- assuming that E= 60 Mpa, I= 60*10 m, and w= 20 N/m. What is…

A: GIVEN :- E=60MPa I=60x10-6 m4 w=20N/m x=0.5m DIAGRAM :- Figure:1. Figure :2.

Q: Hiw: Find the slope and deflection in the Section CA-A) aned the Section (3-B) fur the beam Shown.…

Q: Problem No. 3 Using double integration method to determine the deflection at L and 1.5L for the beam…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

Use moment area method. Give me clear calculations

Determine the deflection @C using Moment Area Method. (Your final answer should
be in "mm")
8 kN/m
3 kN
A
C
D
B
6 m
4 т
3 т
E = 200 GPa
I = 260 x 106 mm4
Note: Express your answer in two decimal places. No need to type the units.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step by step

Solved in 6 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An aluminum bar having a rectangular cross section (2.0 in. × 1.0 in.) and length L = 30 in. is compressed by axial loads that have a resultant P = 2800 lb acting at the midpoint of the long side of the cross section (sec figure). Assuming that the modulus of elasticity E is equal to 10 × 106 psi and that the ends of the bar are pinned, calculate the maximum deflection and the maximum bending moment Mmax.
‘11.5-2 A steel bar having a square cross section (50 mm × 50 mm)and length L = 2.0 in is compressed by axial loads that have a resultant P = 60 kN acting at the midpoint of one side of the cross section (sec figure). Assuming that the modulus of elasticity £is equal to 210 GPa and that the ends of the bar are pinned, calculate the maximum deflection S and the maximum bending moment Mmax.
An object of weight Wis dropped onto the midpoint of a simple beam AB from a height h (see figure). The beam has a rectangular cross section of area A. Assuming that h is very large compared to the deflection of the beam when the weight PFis applied statically, obtain a formula for the maximum bending stress crniilx in the beam due to the falling weight.
determine the deflection at B in mm using Conjugate Beam Method. Consider 150 mm x 200 (b x h) mm section and E=80 GPa. Enter the absolute value only and round off your answer to 3 decimal places Answer asap. I rate
Determine the deflection at Point C of the beam shown below (negative is down). P = 16 kN wo = 29 kN/m E = 192 GPa I = 94.145x10-6 m4 Express your answer using three significant figures and ensure that it is in mm.
Help asap, how can I determine the deflection at point A, B, C, D and E? If E=200MPa and Ixx=169000mm4
A cantilever 8m long carries a uniformly distributed load of 12kN/m from midspan to free end. Determine the deflection at the free end, Find the smallest moment of inertia (in x10^6 mm^4) so that its maximum deflection does not exceed the limit of 1/360 of the span. Use E = 70 GPa. Determine the required depth of beam if it is a rectangular section with width-to-depth ratio of 0.5.
The link CE (Diameter D=12mm) and DF (Diameter D=10 mm) areconnected to rigid link ABCD as shown in the figure. The links CE and DFare made of E=200 GPa steel.a. Find the force at each link (CE and DF)b. Find the deflection at point A.
(1a) A simply supported beam of hollow circular section of external diameter 200mm, and internal diameter 150mm has a span of 6m. It is subjected to concentrated load of 50kN and Udl of 5kN/m over the entire span. Determine the maximum slope at the support and maximum deflection at centre. Take E = 2 x 105N/mm2 (1b)Explain the following terminology: The strain Stress Young modulus in the column. Rigid Prop
A 13 m simply supported beam with a uniform load of 3 kN/m from right end to the left end and has a maximum deflection of __________. Use EI = 11000 kN-m2.
A SSB of 8 m span carries a point load of 10 kN at its centre. It also subjects to a UDL of 1 kN/m over its entire span. Find the maximum deflection of the beam. Take E = 200 kN/mm2, I = 200 x 106 mm4
A SSB of 8 m span carries a point load of 10 kN at its centre. It also subjects to a UDL of 1kN/m over its entire span. Find the maximum deflection of the beam. Take E = 200 kN/mm2,I = 200 x 106mm4.