During laboratory testing of an 8-inch steel-alloy rod with a cross sectional area of 32in a tensile load of 40,000 lbs is applied. If the cross-sectional area decreases to 0.3188in² and lengthens to 8.021 inches, what is the Modulus of Elasticity and Poisson's Ratio? E=6E v = -E(lateral) E(axial)

During laboratory testing of an 8-inch steel-alloy rod with a cross sectional area of 32in a tensile load of 40,000 lbs is applied. If the cross-sectional area decreases to 0.3188in² and lengthens to 8.021 inches, what is the Modulus of Elasticity and Poisson's Ratio? E=6E v = -E(lateral) E(axial)

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.5P: The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen...

See similar textbooks

Related questions

Q: SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and…

Q: Problem 7.1. The aluminum bar (cross section 3 cm x 3 cm) shown the figure below is loaded to its…

A: When the axial load is applied to the specimens or the element of any wood or iron material. It…

Q: A homogenous steel rod has a diameter of 1.5 inches. When a load is applied, it deformed to about…

A: we have a relationshipδ=PLAEP=?L=6×12inE=29×106psiA=π41.52=1.7671in2δ=0.045in

Q: Two bars of different materials and same size are subjected to the same tensile force. If the bars…

A: Given data: Unit elongation =δLδ1Lδ2L=25

Q: Q5 A specimen of magnesium having a rectangular cross section of dimension= (3.2 mm X 19.l mm) and…

A: load extension stress=PA strain=δll 0 0 0 0 1380 0.03…

Q: A tensile load of 190 kN is applied to a round metal bar with a diameter of 16 mm and a gage length…

A: The given data is: Tensile Load on metallic bar (P) = 190 kN Diameter of bar (d) = 16 mm Length of…

Q: A 10.0 mm diameter cylindrical specimen of a bearing bronze material is pulled under uniaxial…

A: given-10.0 mm diameter 1500 N force∆d=0.67 mmn=0.35

Q: A bar is 500 mm long and is stretched to 505 mm with a force of 50 kN. The bar is 10 mm diameter.…

A: Stress- It can be defined as the force acting per unit area, and given by σ=PA Strain- it is defined…

Q: A tensile stress is applied along the long axis of a cylindrical steel rod with adiameter of 10 mm.…

A: The given data is as follows: Diameter=10 mmChange in diameter=5×10-3 mmModulus of elasticity=200…

Q: Aluminum D=20mm Steel 200kN 200KN Bronze D=25mm D=28mm 150kN

Q: } 8) A tensile load of 3000 N is applied to a steel bar of cross-sectional area 500 mm². If a…

Q: The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in…

Q: A steel bar of length 30 m and having specific weight of 20 x 10-5 N/mm³. Find the elongation of the…

Q: Problem :6 Diameter of the metal bar, before and after load application was measured to be 100.00 mm…

Q: Determine strain in rod Initial length=400 mm Change in length=5 mm

A: Given data : Change in length=5 mmInitial length=400 mm

Q: u, A tensile load of 3000 N is applied to a steel bar of cross-sectional area 500 mm. If a tensile…

Q: Mechanical properties of materials H.W.: The following data where obtained during the tensile test…

A: Mechanical properties are those properties of a material which can be observed under the action of a…

Q: to be in tension positive and forces causing the object to be in compression negative. As we can see…

Q: A cylindrical rod with a length of 380 mm and a diameter of 10 mm is to be subjected to a tensile…

Q: An aluminum alloy cylinder with a diameter of 76 mm and a height of150 mm. is subjected to a…

Q: Figure 5 shows a steel rod of 200 mm length (L) with modulus of elasticity, E = 200 GPa and…

Q: A metal rod with 0.5 inch diameter is subjected to 2000 lb tensile load. Calculate the resulting…

Q: Problem 7.1. The aluminum bar (cross section 3 cm x 3 cm) shown the figure below is loaded to its…

A: Procedure: To find the elongation of the bar first we need to find the linear strainε. Then…

Q: snip

A: (a) It is required to determine the stress. σ=LoadArea=250 lbπ4×0.51 in2=1223.80 psi Similarly…

Q: Example 10.6 A railway wagon moving at a velocity of 1.5 m/s is brought to rest by a bumper…

A: We are authorized to answer three subparts at a time, since you have not mentioned which subparts…

Q: A tensile test is performed on a brass specimen 10mm in diameter using a gage length of 50mm When…

Q: 1.4 A tensile load of 190 kN is applied to a round metal bar with a diameter of 16 mm and a gage…

A: Given data, Load P = 190 kN Diameter d = 16 mm Length L = 50 mm Change in length △l = 0.1349 mm…

Q: An aluminum alloy cylinder with a diameter of 3 inches and a height of 6 inches is subjected to a…

Q: A tensile stress is applied along the long axis of a cylindrical aluminum rodwith a diameter of 10…

A: Using the relation of Poisson's ratio to calculate the load that will cause a change of 2.5×10-3 mm…

Q: A specimen of magnesium having a rectangular cross section of dimensions (3.2 mm X 19.1 mm) and gage…

Q: During laboratory testing of an 6-inch aluminum-alloy rod with a cross sectional area of 0.32in², a…

A: Given data : Initial Length (Li)=6 inInitial area (AI)=0.32 in2Tensile load (P)=50000 lbsFinal area…

Q: 2) For a specific material having poisson's ratio -0.32, the percent of elastic modulus to modulus…

Q: A steel rod has a length of 4 ft, and a diameter of 3 inches. Determine the amount of stress in the…

A: Given data : Length (L)=4 ftDiameter (d)=3 inForce (F)=5000 lbModulus of elasticity (E)=30×106 psi

Q: A metal specimen 36mm in diameter has a length of 360 mm. A force of 300 kN elongates the length by…

Q: Determine the maximum tensile strength of the steel bar described by the following data Initial…

Q: Calculate the stiffness of a homogenous bar having elastic modulus of 200 GPa, length of 2 m, and…

A: To find:- the stiffness of a homogenous bar having elastic modulus of 200 GPa, length of 2 m, and…

Q: Three rods jointly support a 7kN load. Assuming that there was no stress in the rods before the load…

A: Given: The load is 7 kN. The length L is 2.75 m. The angles are 25o and 20o. The modulus of…

Q: 2. A steel bar, whose cross section is 0.60 inch by 4.10 inches, was tested in tension. An axial…

A: Note :- as per our guidelines we are supposed to answer first three subparts only. Please repost…

Q: If a steel column with cross-sectional area A = 1000 mm^2 modulus of elasticity E = 200 MPa and…

Q: SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and…

Q: A copper rod with a diameter of 19 mm, modulus of 110 GPa, and a Poisson’sratio of 0.35 is subjected…

A: Given: The diameter of copper d, is 19 mm. Poisson’s ratio is 0.35. The reduction is diameter is…

Q: A1 m long steel rod has a cross sectional area of 100 sqm. It is Elasticity modulus is 200 000 MPa.…

Q: An aluminum rod 20 mm in diameter and 5 m long is subjected to an axial tensile load of 50 kN…

Q: A tensile load of 150 kN is applied to a round metal bar with a diameter of 16 mm and a gage length…

A: Given data in question Length Diameter Elongation in length and Diameter Load To find out…

Q: Q1: The original length of a piece of metal is 400 mm, this piece has pulled in tension with stress…

Q: a) 128.5 GPa A circular rod of diameter 30 mm and length 200 mm is subjected to a tensile force. The…

A: Given, Diameter of the rod = D= 30mm Length= L= 200mm Change in length, ∆L= 0.09 Change in diameter,…

Q: Question: Determine the diameter of the elastic core of the rod ? Options: A. 13.72 mm B.10.34 mm…

A: Given, Length (L) = 1.5 m Diameter (d) = 20 mm

Q: A high strength steel with modulus of elasticity of A N/mm, yield strength of B N/mm2 and crushing…

A: We are required to calculate the ductility of steel

Q: axial loads shown in the figure. The cross-sectional area of the steel, bronze, and aluminum are…

Question

During laboratory testing of an 8-inch steel-alloy rod with a cross sectional area of 32in?,
a tensile load of 40,000 lbs is applied. If the cross-sectional area decreases to 0.3188in?
and lengthens to 8.021 inches, what is the Modulus of Elasticity and Poisson's Ratio?
E= 6/
v = -E(lateral) E(axial)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
A 10 cm long rectangular bar (when subjected to a tensile load) deforms by 0.1 mm. Calculate the normal strain.
An arbitrary material has an elastic modulus of 118 GPa. How much tensile force was applied to a 100 mm-long cylindrical bar that was originally 10 mm in diameter to reduce the area by 0.1%? (NOTE: The material has a Poisson’s ratio of 0.29)
An aluminum tube has an outside diameter of 2.5 inches will be used to support 27 kips of load. If the normal stress in the member must be limited to 18 ksi, how thick in inches should the aluminum be? Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and final answers to 3 decimal places.
A compressive load of 50 KN is applied 150 on the axis of a steel-round bar of 8 mm diameter. Compute its stress and strain if the given modulus of elasticity is 75 GPa. Please draw a figure.
A specimen is originally 1 ft long, has a diameter of 0.5 in., and is subjected to aforce of 500 lb. When the force is increased from 500 lb to 1800 lb, the specimenelongates 0.009 in. Determine the modulus of elasticity for the material if it remainslinear elastic.Note: Draw the given data.
A specimen is originally 300 mm long, has a diameter of 12 mm, and is subjected to a force of 2.4 kN. When the force is increased from 2.4 kN to 9 kN, the specimen elongates 0.250 mm. Determine the modulus of elasticity for the material if it remains linear elastic. Express your answer to three significant figures and include the appropriate units.
A rod made of aluminum alloy, with a gauge length of 100 mm, diameter of 10 mm, and yield strength of 150 MPa, was subjected to a tensile load of 5.85 kN. If the gauge length was changed to 100.1 mm and the diameter was changed to 9.9967 mm,calculate the modulus of elasticity and Poisson’s ratio.
If the bulk modulus of elasticity for water is 2.2 GPa, what pressure is required to reduce a volume by 0.6%?
A cylindrical rod of steel (E = 207 GPa),4mm in diameter is to be deformed by atensile force. Determine the force (in N)that will produce an elastic reduction of2.5 x 10-3mm in diameter if Poisson’sratio is 0.30. Show complete solution and formulas used.
Question 2:A specimen is originally 300 mm long, has a diameter of 12 mm, and is subjected to a forceof 2.5 kN. When the force is increased from 2.5 kN to 9 kN, the specimen elongates 0.225mm. Determine the modulus of elasticity for the material if it remains linear elastic.