ENT 152 Computer Aided Manufacturing I Milling Worksheet-SHOW ALL WORK A milling operation is to be performed at 100 sfpm at .005 ipt. A 500" diameter, 4 flute HSs end mill is to be used. The operation is a slot .100" deep across the diagonal of a rectangular part 4 inches wide and 6 inches long. The material is 4140 medium carbon steel (BHN-250). Use a specific HP of 1.2 HP/in/min. Calculate: RPM feed (ipm) feed (ipr) Cut time MRR c. f. HP required at the spindle

ENT 152 Computer Aided Manufacturing I Milling Worksheet-SHOW ALL WORK A milling operation is to be performed at 100 sfpm at .005 ipt. A 500" diameter, 4 flute HSs end mill is to be used. The operation is a slot .100" deep across the diagonal of a rectangular part 4 inches wide and 6 inches long. The material is 4140 medium carbon steel (BHN-250). Use a specific HP of 1.2 HP/in/min. Calculate: RPM feed (ipm) feed (ipr) Cut time MRR c. f. HP required at the spindle

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Your manager has asked you to submit a report based on lead screws and screw jacks on plant premises. You need to include following calculations for the report. 1. The lead screw of a lathe has Acme threads of 50 mm outside diameter and 8 mm pitch. The screw must exert an axial pressure of 2500 N in order to drive the tool carriage. The thrust is carried on a collar 110 mm outside diameter and 55 mm inside diameter and the lead screw rotates at 30 r.p.m. Determine (a) the power required to drive the screw; and (b) the efficiency of the lead screw. Assume a coefficient of friction of 0.15 for the screw and 0.12 for the collar. 2. The lead screw of a lathe has Acme threads of 60 mm outside diameter and 8 mm pitch. It supplies drive to a tool carriage which needs an axial force of 2150 N. A collar bearing with inner and outer radius as 30 mm and 60 mm respectively is provided. The coefficient of friction for the screw threads is 0.12 and for the collar it is 0.10. Find the torque…
In a slab milling operation , L_w = 200 mm table feed = 18 mm/min, diameter of cutter = 34 mm depth of cut = 2 mm. Considering approach and overtravel to be same. The milling time in min will be?
2.14 W hy is cBN generally preferred over diamond for machining steels?
Please typing answer only IENG 302 - Manufacturing Processes: We are reducing the diameter of a 95.8 mm cylinder to 30.04 mm using 7 roughing passes and 3 finishing passes. The finishing operations use a depth of cut of 1.51 mm. The roughing operations are performed with a feed rate of 9.61 mm/s and the finishing operation is performed with a feed rate of 11.31 mm/s. a) What is the depth of cut for a roughing pass? b) What is the rate of material removal (mm^3/s) for the third roughing pass? c) What is the rate of material removal (mm^3/s) for the final finishing pass? d) What is the average rate of material removal (mm^3/s) for the roughing operations?
Manufacturing Process In a turning operation on stainless steel with hardness = 200 HB, the cutting speed = 200m/min, feed = 0.25 mm/rev, and depth of cut =7.5 mm. Determine how much power will the lathe machine draw in performing this operation if its mechanical efficiency = 90 %. Use specific energy value is: U = 2.8 J/mm
The following data is given for slab milling of a 300 mm long 50 mm wide mild steel block: Cutter of diameter= 60 mm; Numbers of teeth =12; Cutter speed = 120 rev/min; Depth of cut = 3.2 mm; Feed is 0.25 mm/tooth.Determine (i) Table feed in mm/min, (ii) MRR (iii) Power (iv) Torque and (v) Total machining time. Assumesuitable approach and over-run and specific energy of mild steel as 5 Ws/mm3.
A part to be turned in an engine lathe must have asurface finish of 1.6 mm. The part is made of a freemachining aluminum alloy. Cutting speed = 150 m/min,and depth of cut = 4.0 mm. The nose radius on the tool =0.75 mm. Determine the feed that will achieve thespecified surface finish.
help please. thank you Based on what you know about correct moisture content for milling (14%), which sample is reading for milling? why or why not?. please make it Brief thank you!
See image and answer pls
Ax =? and Ay = ? Bx = ? and By = ?
Please solve both part I haven't any credit??
A slab-milling operation is being carried out on a 300 mm long, 100 mm wide annealed mild steelblock at a feed f=0,25 mm/tooth and a depth of cut d=3.0 mm. The cutter isD=50mm diameter, has 20 straight teeth, rotates at N=100rpm, U=3 W.S/mm3 and by definition is wider thanthe block to be machined. Calculate:a. Material Removalb. Estimate the power and torque required for this operationc. Calculate the cutting time