et's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 00 Gpa and a Poisson's ratio of 0.3. If a tensile force F is subjected to that rod cross-section, the diameter becomes 3.998 mm. determine ne applied force F.

et's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 00 Gpa and a Poisson's ratio of 0.3. If a tensile force F is subjected to that rod cross-section, the diameter becomes 3.998 mm. determine ne applied force F.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.3.21P: A slightly tapered bar AB of solid circular crass section and length L is supported at end B and...

See similar textbooks

Related questions

Q: A steel wire 10m long, hanging vertically, supports a load of 22kN. Neglecting the weight of the…

A: To solve this problem, we need to first find the diameter of wire based on allowable stress in the…

Q: Ql; A bar ABCD shown in Figure (1) below consists of three sections: AB is of 42 mm diameter and 80…

Q: Consider tow circular rods with a 50mm diameter are joined by a knuckle joint by a pin of 40mm in…

A: Given: Diameter of the rod D=50mm Diameter of the pin Dp=40mm Tensile force F=120kN

Q: A round steel tension member 40 in. long is subjected to a maximum load of 6,500 lbf. (a) What…

A: Given:- Length : 40 in Load : 6500 lb

Q: A diagonal aluminum alloy tension rod of diameter d and initial length / is used in a rectangular…

A: We have to determine Deformation of aluminum rod

Q: А cube with an edge of 2·5 cm as shown in Fig. 1.4 was tested in compression. Under a load of 400 kN…

A: In compression, we examined a cube with a 2.5 cm edge, as illustrated in the picture. It failed…

Q: Let's consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a…

Q: For a rigid cylindrical steel rod of 2m length 2 cm diameter and yield stress fy = 470 MPa,…

A: Given datalength=2mdiameter= 2 cmyeild stress fy=470 MpaTo determine axial force to yield the rod

Q: Let's consider a rod having a solid circular cross-section with diameter of 5 mm and it is made of a…

A: Given: The initial diameter of the rod is d=5 mm. The Young's modulus of material is E=120 MPa. The…

Q: . A sheet of plywood consists of three equally thick sheets, the upper and lower sheets having their…

A: Given Tensile modulus, E1 = 10 GPa E2 = 0.4 GPa Find Tensile…

Q: et's consider a rod having a solid circular cross-section with diameter of 4 mm and it i5 made of a…

A: given:diamater d=4mmyoung modulus E=200GPapoisson ratio μ=0.3

Q: Let's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a…

Q: determine the required diameter if the stress is not to exceed 140 MPa and the total elongation is…

A: Need to determine the required diameter

Q: Let's consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a…

Q: conpound bar is constructed from threa barg 50 mm wida by 10 mm thick fastened together to form a…

A: Force= shear ×Areax2×50×10×10-6=σA×50×10×10-6σA=2x (stress in aluminium)

Q: steel rod: 0 24 mm 0.4 m 3 m Figure 1.23 A rectangular column of sides 0.4m x 0.35m, made of…

Q: A steel [E = 200 GPa] rod with a circular cross section is 5 m long. Determine the minimum diameter…

A: Given data: The youngs modulus of the rod is, E=200 GPa. The length of the rod is, L=5 m. The…

Q: A brass rod of diameter 50mm and of length 250mm which is subjected to a tensile liad of 300kN when…

A: (a) Diameter of rod = 50 mm Area (A) = πd24Area (A) = 3.14 x 0.0524Area (A) = 0.0019625 m2…

Q: 2. A hollow cylinder 2 m long has an outside diameter of 50mm and inside diameter of 30mm. If the…

Q: 2. An aluminum rod is 1.5 m long. For aluminum, Young's Modulus is E = 70 GPa. An axial force of 3…

Q: Let's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a…

Q: A 1.40 m long steel circular bar is acted upon by forces as shown in fig below. determine the total…

A: To find: The total elongation of the bar. Given: The length of steel bar is Ls=40 cm. The length of…

Q: Let's consider a rod subjected to the shown axial forces. If we consider a lincar elastic behavior,…

A: Stress: Stress is nothing but the force per unit area. It is represented by σ. SI unit of stress is…

Q: A cylinder has an ID of 100 mm and an internal pressure of 50 MPa. Find the needed wall thickness if…

A: Given data: cylinder Internal diameter=Di =100mm Internal pressure=Pi…

Q: A circular steel bar is subjected to various forces as shown in Fig. determine: 1) P 2) The total…

A: Given: A circular steel bar is shown below:

Q: 1. Determine the internal stresses developed in bars JH and HY when bar JH experiences a change in…

A: It is asked to find the stress generated in the bars due to temperature change

Q: If a solid circular rod having an initial diameter D = 0.03 m and initial length L = 0.8 m, is…

A: Given: Initial Diameter of the solid circular rod, Di=0.03m Initial length of the solid circular…

Q: A Cantilever ród is loades as shown in the frguirel, If the tensle yield strength f the materreul is…

A: Given: τ=300 MPaT=800 N.mP=10 kNF=2 kN

Q: Let's considera rod having a solid circular cross-section with diameter of 5 mm and it is made of a…

Q: Let's consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a…

A: In possion's ratio always consider change in diameter without concerning the sign only take…

Q: Rod (2) Rod (1)

A: Given that, Diameter of the circular rod, D=50 mm,Diameter of the pin, d=40 mm,Tensile force applied…

Q: 2:The load (50 kN) applied on the rigid beam (AB) s supported by the pin (A) and two rods ,one made…

Q: A stepped circular bar having diameters 20 mm, 15: mm and 10 mm over axial lengths of 100 mm, 80mm…

A: Write the given data. d1=20 mmd2=15 mmd3=10 mmL1=100 mmL2=80 mmL3=60 mmL=240 mmF=5 kNE=100×103…

Q: OF = 5712 N

A: Calculate linear strain with the given data

Q: Q 2: A circular rod of 15 mm diameter and 120 mm length, is subjected to 2.5 KN tensile load if the…

Q: Let's consider a rod having a solid circular cross-section with diameter of 5 mm and it is made of a…

A: Given:- Diameter of rod: d =5 mm Young's modulus: E=120 GPa Poisson's ratio: μ=0.33 new diameter:…

Q: Column is manufactured using concrete (E=4.2×10^3 ksi) and reinforcement is done by A-36 steel rods…

Q: Two vertical steel rods support the rigid bar as shown. Initially, the rods are stress-free. Given…

A: given; →P=20KN =20*103N→E=200GPa =200*103MPa→lets take tension in rod B=TB→lets take tension…

Q: determine the applied force F.

Q: 2. A steel bar that is 5.75 m long must support a tensile load of P = 20 kN without stretching more…

Q: Asteel alloy sPeeimen having a rectangular crass section of dimen sians lomm X 5mm has the…

A: A) Amount of stress induced =σ=PA=2000010×5=400MPaAmount of elastic strain…

Q: Let's consider a rod having a solid circular cross-section with diameter of 5 mm and it is made of a…

A: poisson's ratio is the ratio of lateral strain to longitudinal strain.

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

Q: A steel [E=200 GPa] rod with a circular cross section is 10 m long. Determine the minimum diameter…

A: Given data as per question Length of the bar =10 m Tensile force = 260 kN we know thatNormal stress…

Q: A hydraulic press exerts a total load of 5.5 MN. This load is carried by two steel rods supporting…

Q: O Solve two problems on statically indeterminate structures(strain energy method), two on thin wall…

A: Given: The outer diameter of the steel cylinder is D = 360 mm. The inner diameter of the steel…

Q: Let's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a…

Q: De ter mia the tensile and Compresnu stress for the bea shown in fig 160 lo wlm 2. m 20 mm 120 I =…

Q: urses This course EHide blocks OP=294 N O P = 235 N Let's consider a rod having a solid circular…

Concept explainers

Conduction and Convection

When energy travels from one object to another it is said to have undergone heat transfer. Heat transfer is nothing but the transfer of thermal energy or internal energy from one thing to another, like e.g., when a vessel with water, kept on top of a burner, heats up because of the flame underneath it.

Question

EHide bl
OP=287 N
OP=573 N
Let's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E =
200 Gpa and a Poisson's ratio of 0.3. If a tensile force F is subjected to that rod cross-section, the diameter becomes 3.998 mm. determine
the applied force F.
Select one:
OF=10472 N
OF=15708 N
OF=6283 N
O F= 4189N
F = 13090 N
OF= 5236 N
Finish attempt..
US ACTIVITY
O Test-Spring 2020-2021
Jump to...

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.
An elevated jogging track is supported at intervals by a wood beam AB (L = 7.5 ft) that is pinned at A and supported by steel rod BC and a steel washer at B. Both the rod (dBC= 3/16 in.) and the washer (dB= 1.0 in.) were designed using a rod tension force of TBC=415 lb. The rod was sized using a factor of safely of 3 against reaching the ultimate stress tru— 60 ksi. An allowable bearing stress sba= 565 psi was used to size the washer at B. A small platform HF is suspended below a section of the elevated track to support some mechanical and electrical equipment. The equipment load is uniform load q = 50 lb/ft and concentrated load WE= 175 lb at mid-span of beam HF. The plan is to drill a hole through beam ABaX £land install the same rod (dBC) and washer) dB) at both D and F to support beam HF. (a) Use s and to check the proposed design for rod DF and washer d,: are they acceptable? (b) Re-check the normal tensile stress in rod BC and bearing stress at 8 if either is inadequate under the additional load from platform HF. Re-design them to meet the original design criteria.
A W410 × S5 steel column is compressed by a force P = 340 kN acting with an eccentricity e = 38 mm, as shown in the figure. The column has pinned ends and a length L. Also, the steel has a modulus of elasticity E = 200 GPa and yield stress y= 250 MPa. P = 340 kN If the length L = 3 m, what is the maximum compressive stress maxin (he column? If a factor of safety n =2.0 is required with respect to yielding, what is the longest permissible length Lmaxof the column?
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?
A rubber sheet in biaxial stress is subjected to tensile stresses ax= 270 Pa ander,. = 144 Pa. The corresponding strains in the sheet are e. = 0.0002 and = 0.000015. Determine Poisson’s ratio and the modulus elasticity of the material.
A circular copper bar with diameter d = 3 in. is subjected to torques T = 30 kip-in. at its ends. Find i lie maximum shear, ion si le. and compressive stresses in the tube and their corresponding strains. Assume that G = 6000 ksi.
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A copper rod of length L = 18.0 in. is to be twisted by torques T (see figure) until the angle of rotation between the ends of the rod is 3.0°. (a) If the allowable shear strain in the copper is 0.0006 rad, what is the maximum permissible diameter of the rod? (b) If the rod diameter is 0.5 in., what is the minimum permissible length of the rod?