For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the beam, (b) the location of the maximum deflection, and (c) the maximum beam deflection. Assume that EI is constant for the beam. Let w = 12 kN/m, L = 6.0 m, E = 215 GPa, and I = 105 x 106 mm4. For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the beam, (b)the location of the maximum deflection, and (c) the maximum beam deflection. Assume that El is constant for the beam. Let w = 12kN/m, L = 6.0 m, E = 215 GPa, and I = 105 x 106 mm4.WoBAnswer:(b) x =m(c) Vmax =mm

Answered: Image /qna-images/answer/56bc17d8-f93e-4e69-b31b-5714b87c7f16.jpg

For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the beam, (b) the location of the maximum deflection, and (c) the maximum beam deflection. Assume that El is constant for the beam. Let w = 12 kN/m, L = 6.0 m, E = 215 GPa, and I = 105 x 106 mm4. B Answer: (b) х 3D (c) Vmax = mm

For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the beam, (b) the location of the maximum deflection, and (c) the maximum beam deflection. Assume that El is constant for the beam. Let w = 12 kN/m, L = 6.0 m, E = 215 GPa, and I = 105 x 106 mm4. B Answer: (b) х 3D (c) Vmax = mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.5.4P: Beam ABC is loaded by a uniform load q and point load P at joint C. Using the method of...

See similar textbooks

Similar questions

.2 A ligmio.irc ii supported by two vorlical beams consistins: of thin-walled, tapered circular lubes (see ligure part at. for purposes of this analysis, each beam may be represented as a cantilever AB of length L = 8.0 m subjected to a lateral load P = 2.4 kN at the free end. The tubes have a constant thickness ; = 10.0 mm and average diameters dA = 90 mm and dB = 270 mm at ends A and B, re s pec lively. Because the thickness is small compared to the diameters, the moment of inerlia at any cross section may be obtained from the formula / = jrrf3;/8 (see Case 22, Appendix E); therefore, the section modulus mav be obtained from the formula S = trdhlA. (a) At what dislance A from the free end docs the maximum bending stress occur? What is the magnitude trllul of the maximum bending stress? What is the ratio of the maximum stress to the largest stress (b) Repeat part (a) if concentrated load P is applied upward at A and downward uniform load q {-x) = 2PIL is applied over the entire beam as shown in the figure part b What is the ratio of the maximum stress to the stress at the location of maximum moment?
Beam ABC is loaded by a uniform load q and point load P at joint C. Using the method of superposition, calculate the deflection at joint C. Assume that L = 4 m, a =2ra, q = 15 kN/m, P = 7.5 kN, £ = 200 GPa, and / = 70.8 X 106 mm4.
A simple beam AB of length L and height /; undergoes a temperature change such that the bottom of the beam is at temperature 7™, and the top of the beam is at temperature Tx(see figure). Determine the equation of the deflection curve of the beam, the angle of rotation 9Aat the left-hand support, and the deflection 8mjLXat the midpoint.
-22 Derive the equations of the deflection curve for a simple beam AB with a distributed load of peak intensity q0acting over the left-hand half of the span (see figure). Also, determine the deflection cat the midpoint of the beam. Use the second-order differential equation of the deflection curve.
A sandwich beam having steel faces enclosing a plastic core is subjected to a bending moment M = 5 kN · m. The thickness of each steel face is 1 = 3 mm with modulus of elasticity E = 200 GPa, The height of the plastic core is hp= 140 mm, and its modulus of elasticity is Ep= 800 MPa. The overall dimensions of the beam are h = 146 mm and h = 175 mm. Using the transformed-section method, determine the maximum tensile and compressive stresses in the faces and the core.
A simple beam AB of length L and height h (see figure) is heated in such a manner that the temperature difference 7= T{between the bottom and top of the beam is proportional to the distance from support A: that is, assume the temperature difference varies linearly along the beam: T2- Tt= Tax in which 7"0 is a constant having units of temperature (degrees) per unit distance. Determine the maximum deflection SW9Xof the beam, Repeat for a quadratic temperature variation along the beam, so T2+T1= Tax
-20 Derive the equations of the deflection curve for a cantilever beam AB carrying a uniform load of intensity q over part of the span (see figure). Also, determine the deflection Bat the end of the beam. Use the second-order differential equation of the deflection curve.
Beam ACB hangs from two springs, as shown in the figure. The springs have stiffnesses Jt(and k2^ and the beam has flexural rigidity EI. What is the downward displacement of point C, which is at the midpoint of the beam, when the moment MQis applied? Data for the structure are M0 = 7.5 kip-ft, L = 6 ft, EI = 520 kip-ft2, kx= 17 kip/ft, and As = 11 kip/ft. Repeat part (a), but remove Af0 and instead apply uniform load q over the entire beam.
For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the beam, (b) the location of the maximum deflection, and (c) the maximum beam deflection. Assume that EI is constant for the beam. Let w = 11 kN/m, L = 4.5 m, E = 185 GPa, and I = 140 x 106 mm4.
For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the cantilever beam, (b) the deflection at B, (c) the deflection at the free end, and (d) the slope at the free end. Assume that EI is constant for the beam. Let w = 15 kN/m, L = 3.5 m, E = 185 GPa, and I = 110 x 106 mm4
For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the cantilever beam AB, (b) the deflection at the free end, and (c) the slope at the free end. Assume that EI is constant for the beam. Let w0 = 6 kN/m, L = 5.5 m, E = 195 GPa, and I = 140 x 106 mm4.
Find the slope and deflection equations for the beam shown. Determine thevertical deflection of point C. Consider P = 120 kN, l = 5m, a = 80 cm. EI = constant. Method of Double Integration