Given your choice of Flame AA, ICP-AE, XRF, EI-MS, or none of these, and keeping in mind that cost matters, which would you use a. for a nondestructive measurement of a sample? b. to determine 10ppm Zn in a solution? c. to determine the amount of Br in a mixture of KBr, KCL and KI? d. to determine the number of Bratoms in a molecule of an organic liquid? e. to determine 10ppb of Fe in motor oil?

Given your choice of Flame AA, ICP-AE, XRF, EI-MS, or none of these, and keeping in mind that cost matters, which would you use a. for a nondestructive measurement of a sample? b. to determine 10ppm Zn in a solution? c. to determine the amount of Br in a mixture of KBr, KCL and KI? d. to determine the number of Bratoms in a molecule of an organic liquid? e. to determine 10ppb of Fe in motor oil?

Organic Chemistry: A Guided Inquiry

2nd Edition

ISBN:9780618974122

Author:Andrei Straumanis

Publisher:Andrei Straumanis

ChapterL3: Carbon (13c) Nmr Spectroscopy

Section: Chapter Questions

Problem 13CTQ

See similar textbooks

Similar questions

This is a ATR spectrum. In which caffeine/PVA films were measured. Line a) correspond to a pure pva film and the other lines are films at increasing caffeine concentration. Notice that the OH band at around 3200cm-1 decreases at higher caffeine concentrations. However at a certain concentration (line d) such band starts to increase back to the initial intensity. What does that mean? Waht is the chemical meaning for that behavior?
Fluorescence intensity was taken of 2.0 mL of the 10 μg/mL quinine standard solution into five 25 mL volumetric flasks. Into one, place 1.0 mL of 0.05 M sodium bromide solution and dilute to the mark with 0.05 M sulfuric acid solution. Similarly, add 2.0, 4.0, 8.0, and 16.0 mL of the sodium bromide solution to the remaining flasks before diluting to volume with the sulfuric acid solution. Why did the fluorescence intensity decrease as the concentration of sodium bromide increased? Only typed and correct answer with explanation please
6. A sample of an alum was analysed by atomic spectroscopy and gravimetrically to determine its structure. A 0.1000 g of the sample when treated with BaCl₂ produced 0.0984 g of a white solid after drying to constant weight. Another 0.1000 g sample of the alum when heated at 105°C for several hours produced a weight loss of 0.04558 g while the % of K in the sample was determined by atomic spectroscopy to be 8.240%. Use these results to work out a formula for the alum. [M,/ g mole¹: K 39.10; Al 26.98; BaSO, 233.39; SO² 96.06; H₂O 18.0148]
Please help me fill the remaining spaces. The spaces marked with NA don't need to be calculate. Name Molecular Weight Amounts used mmol Equivalents M.P or BP (C) Density (g/mL) Indene 116.16 .5mL MP=-2 BP=181-182 .996 Borane-tetrahydrofuran Complex 85.94 2.8mL 1 MP= -108 BP=66 NA 30% Hydrogen Peroxide 34.01 1mL MP= -33 BP=108 NA 3 M NaOH(aq) 40 .7mL MP=318 BP=1390 NA Diethyl Ether 74.12 NA NA NA BP=75-78 .902 Hexanes 86.17 NA NA NA BP=65.5-68.3 .659 Potassium Permanganate 158.03 NA NA NA BP=100 1.0 1-Indanol (Product) 134.13 NA MP=50-54 NA 2-Indanol (Product) Same as Above Same as Above Same as Above NA MP=68-71 NA
In HPLC, why is purging or initialization being done before analysis of samples, explain.
Calculate the amount of phycocyanin in Sample 1 in mg where A620 = 0.193 and A650 = 0.095, taking into account the dilution factor of 100 ul, and the total volume of extract 45ml. Note your answer to 2 decimal places.
Graphite furnace atomizers are renowned in Atomic Absorption Spectrometry for their exceptionally low detection limits (10-12 g and lower for many elements). Why are detectabilities so much better with graphite furnaces than with flame atom cells in AAS?
1. Define sparging. What is the significance of this step in an HPLC analysis? 2. What are the two types of pre-column? What is the purpose of each type? 3. What are the two types of packing used in HPLC column? Describe each type. Please answer numbers 1-3. Need asap
Explain the difference between absorption and adsorption in natural dyes. Use sketches to clarify your explanation.
I need help darwing a TLC plate and figuring out the Rf values is the retention factor values We estimate our own TLC plate of Anthracene, Maleic Anhydride, and the Diels-Alder Adduct and determine the Rf values for the three materials
On the blank TLC provided to the right, please draw where you would expect to see the spots for B-carotene (lane 1), compound A (lane 2) and compound B (lane 3). This is SiO2 plate and the appropriate developing solvent is used.
What causes exposure or closeness in humans: [Explain in detail and thenjustify why]a) to an IR lamp?