The steel shaft is made from two segments: AC has a diameter of 50 mm, and CB has a diameter of 100mm. If the shaft is fixed at its ends A and B and subjected to a torque of 800 N.m, and G = 76 GPa.st50 mms00 N.m30 mm100 mm80 mm120 mm1- What is the torque value at polint A in (N.m)?O 88.32O 411.76658.82O. 141.18O 264.71None2- What is the maximum shear stress in the shaft in (MPa)?O 8.63O 5.75O3,60O 10.79O 2.87O None

Given: The diameter of segment AC, d = 50 mm The diameter of segment CB, D = 100 mm The torque…

he steel shaft is made from two segments: AC has a diameter of 50 mm, and CB has a diameter of 100 nm. If the shaft is fixed at its ends A and B and subjected to a torque of 800 N.m, and G = 76 GPa. %3D st 50 mm 30 mm 800 N.m 80 mm 100 mm 120 mm 1- What is the torque value at point A in (N.m)? O 88.32 O 411.76 658,82 O 141.18 O 264.71 None 2- What is the maximum shear stress in the shaft in (MPa)? O 8.63 O 5.75 O 3.60 O 10.79 O 2.87 O None

he steel shaft is made from two segments: AC has a diameter of 50 mm, and CB has a diameter of 100 nm. If the shaft is fixed at its ends A and B and subjected to a torque of 800 N.m, and G = 76 GPa. %3D st 50 mm 30 mm 800 N.m 80 mm 100 mm 120 mm 1- What is the torque value at point A in (N.m)? O 88.32 O 411.76 658,82 O 141.18 O 264.71 None 2- What is the maximum shear stress in the shaft in (MPa)? O 8.63 O 5.75 O 3.60 O 10.79 O 2.87 O None

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A shaft required to transmit 50kW of power will be running at 100rev/min. The maximum twist in 3m length of the shaft is limited to 1.5 degree. If the maximum torque is 30 percent more than mean or average torque. Assume entirely elastic action and take modulus of rigidity for the shaft material G = 135 GN/?2. Determine the following:a. Diameter of the shaft.b. Maximum shear stress developed in the shaft. I need answer ASAP. Thank you!
A shaft is made of a steel alloy having an allowable shear stress of 10 ksi and the diameter of the shaft is 1.2 inch determine the maximum torque T that can be transmitted.
Determine the torque that can be transmitted by a shaft of 50 mm diameter, if the maximum allowable angle of twist is 2° in a length of 100 cm. Take G = 80000 .
The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the maximum torque T (in Nm) that can be applied to the ends of the shaft without exceeding a shear stress of 70034763 Pa and angle of twist of 2.23ᴼ. Use G = 83000000000 Pafor the shaft, x = 2.3 m, and y = 1.89 m. Round off the final answer to two decimal places.Please help me, I only have 30 mins left. TY!
If the permissible shear stress of a solid shaft is of 70MPa, the torque angle between two cross sections separated 2.5m does not exceed 3°, the applied torque is of 1400N.m and G=11Gpa a. Determine the required diameter in function of the shear stress b. Determine the required diameter in function of the angle of twist
The mean dimensions of the cross-section of the leading edge and torsion box of an airplane wing can be approximated as shown. If the wing is made of 2014-T6 (G = 19 GPa) aluminum alloy having an allowable shear stress of Tallow = 158 MPa, and the wall thickness is 12 mm. Determine the maximum allowable torque and the corresponding angle of twist per meter length of the wing.
What is the minimum diameter of a solid steel shaft that will not twist through more than 10 degrees in a 6 m length when subjected to a torque of 28 kN.m.?Use G=83 GPa. 131.33 mm 125.22 mm 118 mm 104.25 mm
If the shaft is made of red brass C83400 copper with an allowable shear stress of ?allow = 20 MPa, determine the maximum allowable torques T1 and T2 that can be applied on A and B. Also, find the corresponding angle of twist of end A. Set L = 0.75 m "Mechanics of Materials, Hibbeler"
A solid circular shaft is acted upon by thetorques as shown. If G= 12, 000 ksi determine:a. Rotation of wheel D with respect to A.b. Shear stress at point EDiameter of shaft:A-B = 2inC-D = 2inB-C = 4inT1 = 2.5 π in.kipsT2 = 8.5 π in.kipsT3 = 7 π in.kipsT4 = π in.kips
The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. the allowable shear stresses for the magnesium and steel sre Tallow mg =45Mpa ve Tallow st=72MPa, respectively. The shear modulus of elasticity for Am1004-T61magnesium alloy is 18Gpa and for A-36 steel is 75Gpa. a)Determine the maximum allowable torque that can be applied at A. b)Find the corresponding angle of twist of end A.
What is the minimum diameter of a solid steel shaft that will not twist through more than 3° (degrees) in a 6 m. length when subjected to a torque of 14 kN-m? Use G = 83 kN/ m^2. Convert your answers to mm.
A solid shaft has a diameter of 40 mm and length of 1 m. It is made from an elastic-plastic material having a yield stress of tY = 100 MPa. Determine the maximum elastic torque TY and the corresponding angle of twist. What is the angle of twist if the torque is increased to T = 1.2TY? G = 80 GPa.