Answered: In a full wave bridge rectifier, the…

In a full wave bridge rectifier, the transformer secondary voltage is 20sinwt. The forward resistance of each diode is 252 and load resistance is 1.5KN. Calculate, i. Im ii. Ide ii. Pdc

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Related questions

Q: Given a half wave rectifier wiith input voltage at the primary of 110 volts rms and turns ratio of…

A: Given:Vrms = 110VNPNS =10load resistance =5000Ω1) At primary,Vrms =Vpeak2Vpeak=2×110 =…

Q: A full wave rectifier circuit is fed with from a transformer having a center tapped secondary…

A: Given information: Vrms=30 VRf=2Ω, Rs2=8 Ω RL=1 kΩ Determining the peak current. Im=VmRf+Rs2+RL…

Q: show how to connect the diodes in a center -tapped rectifier in order to produce a negative- going…

A: Centre tapped full wave rectifier

Q: The 12.6V secondary of a transformer is connected to a half-wave rectifier and a 20-ohms load…

Q: An FWR using a centre-tapped Transformer Supplies an average voltage of 120V to a 250 kΩ load…

A: A)Average output voltage of FWR is =2Vmπ=120 VVm=120×π2Vm=188.5 V

Q: Q/Why does the zener diode not work when a voltage is applied less than its voltage, and what is the…

A: Zener diode is designed to work as voltage regulator means it will regulate the voltage value upto a…

Q: b) Consider a full wave center tap rectifier circuit made up of silicon diodes, containing output ac…

A: Centre tapped full wave rectifier,

Q: Explain the firing angle range in the half-wave and full-wave controlled rectifier circuits feeding…

A: The solution is mentioned below

Q: A center tapped rectifier is supplied using 220 V,60 Hz supply, then using ideal mode, the peak…

A: Given, A center tapped rectifier has, Input voltage (Vi)= 220 volts (rms value) Frequency (f)= 60 Hz

Q: Write the following for a Semiconverter rectifier with RL load: a) Draw the circuit diagram, supply…

A: There are many devices that work with DC supply, but the supply present is naturally AC. The…

Q: 2.21 What PIV rating is required for the diodes in a bridge rectifier that produces an average…

A: Given: A bridge type rectifier whose average output voltage is 50V. According to question:…

Q: 4. General Purpose Diodes are mostly preferred in chopper circuits. Is it True? Justify.

A: Ans. No

Q: 28. A full-wave bridge rectifier with a 120-V rms sinusoidal input has a load resistor of 1 kN. a.…

A: In this question, We need to determine the dc average voltage Vdc? , PIV, maximum current rating…

Q: Q2. A three phase full wave uncontrolled bridge rectifier has an AC input voltage of 90 V RMS at 60…

A: Given data, Supply RMS voltage Vr=90 V. Frequency f=60 Hz. Load resistance RL=440 Ω.

Q: 38. The single-phase ac center-tap full-wave rectifier input voltage is 230 V (rms). Determine the…

Q: A three-phase, half-wave uncontrolled rectifier is fed from an ideal three-phase voltage source of…

A: " Since you have posted a question with multiple subparts, we will solve the first three subparts…

Q: A three-phase, half-wave uncontrolled rectifier is fed from an ideal three-phase voltage 50 Hz. The…

A: According to the question we have to calculate, (a) The average output voltage and average load…

Q: A three phase full wave uncontrolled bridge rectifier has an AC input voltage of 90 V RMS at 60 Hz…

A: Given, A three phase full wave uncontrolled bridge rectifier, Vin= 90V rms (line…

Q: A classical rectifier is to be designed to provide 5V ± 1% for a logic circuit, with output power of…

A: Given:Vout = 5V ±17°Pout = 12WVin = 120Vf = 50Hzi) and ii)Diode configuration is full wave bridge…

Q: A full-wave Bridge rectifier with 120 V-rms sinusoidal input has a load resistor of 1 kn. (a) If…

Q: A classical rectifier is to be designed to provide 5V+ 1% for a logic circuit, with output power of…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: Figure shows an AC source G having an effective voltage of 240 V, 60 Hz is connected to a…

A: Let us assume, that a constant current I0 flows through the given RL load. Calculate the dc output…

Q: Write the following for a Semiconverter rectifier with RL load: a) Draw the circuit diagram, supply…

A: Explanation: a) In the semi converter rectifier with RL load we use two diodes and two SCRs. Let Vs…

Q: A filtered 4 diode full wave rectifier circuit with the following specifications: The line load is…

Q: A l-phase bridge rectifier has to supply power to a 300 kW, 120 V DC load. A 240 V, 60 Hz AC feeder…

A: Given data, Po=300 KWVo=120 VVi/p=240 Vf=60 Hz (a)

Q: When the rms output voltage of a full-wave bridge rectifier is 26.20 V, the peak inverse voltage…

Q: Consider a full wave bridge rectifier, whose transformer secondary voltage is 130sinwt. If the…

Q: Connect the half-wave rectifier with resistive load (RL=1KΩ ) and set the parameters value of peak…

A: The half wave rectifier circuit diagram and its working is thoroughly explained along with the…

Q: What is the PIV rating of each silicon diode in volts for a bridge type rectifier where the voltage…

A: To charge a battery from AC supply or convert AC into DC rectifier (converter) circuits are used.…

Q: 9. The diodes in a bridge rectifier each have a maximum dc current rating of 2 A. What is the…

A: For both the questions we are given rectifier type as bridge rectifier A bridge rectifier contains…

Q: Determine the peak output voltage for the bridge rectifier in this figure. Assuming the practical…

A: Introduction: Bridge rectifier is full wave rectifier circuit, converts AC in DC. Transformer steps…

Q: A classical rectifier is to be designed to provide 5V ± 1% for a logic circuit, with output power of…

A: Given,Output power, Pout=12WInput voltage, Vin=220VFrequency, f=50HzOutput voltage, Vout=5V±1%

Q: 2. Draw unregulated dc voltage circuit using bridge rectifier circuit with a smoothing capacitor.…

A: Here we discuss about an unregulated power supply.

Q: Explain the principle operation for a diode and how it is used as a rectifier.

A: Diode is a two terminal device which have two terminals such as a anode and cathode. Diode easy…

Q: The half-wave rectiﬁer as shown is operating at a frequency of 60Hz, and the rms value of the…

A: Given data, The value of rms voltage is Vrms = 12.6±10% V. The value of operating frequency is f =…

Q: EXAMPLE: A single-phase, full-wave center-tapped rectifier supplies power to a 1-k2 load. The ac…

Q: A classical rectifier is to be designed to provide 5V  1% for a logic circuit, with output power of…

A: A diode is a two-terminal one-way switch, it will only allow the flow of current in one direction,…

Q: 3. Full Wave Center Tapped Rectifier a. Determine V, and the required PIV rating of each diode for…

Q: Q: - Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage…

A: To charge a battery from AC supply or convert AC into DC rectifier (converter) circuits are used.…

Q: 04: A full-wave bridge rectifier at (2:3) transformer with a [77 sin(2n x 100 x 10°t)] rms input…

Q: Design Half-wave Rectifier Circuit to provide an output of 100 VDC. Then calculate its transformer…

Q: 28. A full-wave bridge rectifier with a 120-V rms sinusoidal input has a load resistor of 1 kſN. a.…

A: As per the guidelines of Bartley we supposed to answer first three subpart only for solution of…

Q: How is Zener diode connected into a circuit?

A: BJT and MOSFET are the class of transistors used in analog electronics. They are widely used…

Q: 2. What is the value of the peak inverse voltage on the diode in half -wave rectifier?

A: As per Bartleby guidelines we are allowed to solve only three subparts please ask the rest again.…

Q: Determine the peak output voltage for the bridge rectifier shown below. Assuming the practical…

A: The diodes are made of semiconductor materials. Silicon and germanium are common semiconductors for…

Q: 1/ derive Vout of single phase half wave uncontrolled rectifier with RE load

A: Note: As per the company policy, we experts are allowed to answer only one question. Kindly post the…

Q: A What could happen if the Zener diode would be changed to a Zener which has a higher breakdown…

A: A) if we replace a Zener diode with a Zener having higher breakdown voltage than the range of…

Q: 2. What is the value of the peak inverse voltage on the diode in full-wave rectifier?

A: In this question we will write PIV of full wave rectifier..

Q: Q7. What is the specialty of Zener diode so as we can operate it in breakdown region for longer…

A: Since zener diodes are highly doped than a normal diode and hence depletion layer is less wider as…

Question

In a full wave bridge rectifier, the transformer secondary voltage is 20sinwt. The
forward resistance of each diode is 252 and load resistance is 1.5KN.
Calculate,
i.
Im
ii.
Idc
iii.
Pdc
iv.
Pac
V.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Single Phase Controlled and Uncontrolled Rectifiers

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the difference between a diode and rectifier?
How is a solid-state diode tested? Explain.
Determine the peak output voltage for the bridge rectifier in this figure. Assuming the practical model, what PIV rating is required for the diode? The transformer is specified to have a 12 Vrms secondary voltage for the standard 110 V across the primary.
Sketch current I vs, voltage V for the circuits below. The breakdown voltage of the Zener diodes are shown. Assume 0.6V for all diodes (including Zener diodes) in the forward bias region.
1N4001, 1N4002, 1N4003, 1N4004, 1N4005, 1N4006 and 1N4007 For any of the diodes, describe with the aid of diagrams/illustrations its applications in an AC to DC Bridge rectifier power supply circuit. For your circuit show and describe how you are going to smooth out the ripple voltage that will be present.
In a center-tapped full wave rectifier circuit utilizing ideal diodes, if the primary voltage is 160Vpeak, the turns ratio is 8:1 and the load resistance is 860 ohms, what is the rectified dc voltage at the output? express answer in volts
Design Half-wave Rectifier Circuit to provide an output of 100 VDC. Then calculate its transformer peak voltage rating, the diode PIV rating, and the transformer turns ratio, if the power is taken from the 220V line AC supply
(a)Derive the average and rms output voltages and currents for three-phase half controlled rectifier with free wheeling diode and RLE load.(b))In a single phase full converter, if output voltage has peak and average values of 325V and 133V respectively, find the firing angle.
The half-wave rectiﬁer as shown is operating at a frequency of 60Hz, and the rms value of the transformer output voltage vI is 12.6V±10%. What are the nominal and worst case values of the dc output voltage VO if the diode voltage drop is 1V?
Determine the ripple factor for the filtered rectifier circuit below when RL= 4KQ. Then explain briefly the effect of changing in the RL value on the output waveform.
Two identical Schottky diodes are connected in series, one in the forward and the other in reverse direction, see figure. Assume the reverse saturation current, IS, of each diode to be known. Derive he current-voltage curve I(V) of this circuit. Plot it with the ratio I / IS on the y-axis and V / Vth on the x-axis. Make sure to cover a broad range of voltages, say, from –10 Vth to 10 Vth.
A step-down transformer supplies 25Vrms to a simple half wave rectifier power supply which is connected to a load resistance of 912ohm. The diode breakdown voltage, Vf is 0.7 V. Calculate the peak signal voltage received by the diode