Connect the half-wave rectifier with resistive load (RL=1KΩ ) and set the parameters value of peak amplitude equal (220) volt, frequency equal (50) HZ. 2- Draw the output waveform for the DC output and the r.m.s value of the output voltages. 3- What is the value of the peak inverse voltage on the diode in half -wave rectifier?

Connect the half-wave rectifier with resistive load (RL=1KΩ ) and set the parameters value of peak amplitude equal (220) volt, frequency equal (50) HZ. 2- Draw the output waveform for the DC output and the r.m.s value of the output voltages. 3- What is the value of the peak inverse voltage on the diode in half -wave rectifier?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
In a center-tapped full wave rectifier circuit utilizing ideal diodes, if the primary voltage is 160Vpeak, the turns ratio is 8:1 and the load resistance is 860 ohms, what is the rectified dc voltage at the output? express answer in volts
Full-wave Bridge rectifier What is the effect of interchanging the probe connection to the resistor voltage waveform? What about, what is the effect of removing one diode from the circuit to the resistor voltage waveform?
For a single phase half wave rectifier feeding 10 ohms load with input supply voltage of 796 V and frequency of 50Hz, Determine Pac, Pdc, FF, RF, TUF, PIV of the diode, and input PF
The full-wave rectiﬁer ias shown is operating at a frequency of 60 Hz, and the rms value of the transformer output voltage is 18 V. (a) What is the value of the dc output voltage if the diode voltage drop is 1 V? (b) What is the minimum value of C required to maintain the ripple voltage to less than 0.25 V if R = 0.5 Ω? (c) What is the PIV rating of the diode in this circuit? (d) What is the surge current when power is ﬁrst applied? (e) What is the amplitude of the repetitive current in the diode?
Determine the peak output voltage for the bridge rectifier in this figure. Assuming the practical model, what PIV rating is required for the diode? The transformer is specified to have a 12 Vrms secondary voltage for the standard 110 V across the primary.
What is the PIV rating of each silicon diode in volts for a bridge type rectifier where the voltage in the secondary transformer is 100V peak? Assume 2.2K ohms load.
The measured values of the diode at temperature of 288 Kelvin's ,are Vd=1.0v at ld=10A and Vd=1.5V at Id=90KA. Determine the emission coefficient of the diode? (i) Explain clearly, using simple sketches how a signal diode differs from a power diode (ii)State the one disadvantage of three phase half wave uncontrolled rectifier
A three-phase, half-wave uncontrolled rectifier is fed from an ideal three-phase voltage source of 380V, 50 Hz. The load is resistive with R=15 2. Calculate: (a) The average output voltage and average load current of the rectifier. (b) The d.c. and a.c. power dissipations in the load. (c) The diode ratings. (d) What is the lowest ripple frequency of the output voltage waveform?
What are the values of the dc output voltage and dc output current for a halfwave rectiﬁer that is being supplied from a transformer having a secondary voltage of 10 Vrms (60 Hz) and a 2-Ω load resistor? Assume the diode on voltage Von = 1 V. What value of ﬁlter capacitance is required to have a ripple voltage of no more than 0.1 V? What is the conduction angle?
3.4 PRE-LABORATORY QUESTIONS 1. What is a rectifier? 2. How does a diode act as a rectifier? 3. What is the significance of PIV? What is the condition imposed on PIV? 4. What is meant by regulation? 5. What is meant by time constant? 6. What is meant by ripple factor?