In relation to this question: Compute for the actual moles of acetic anhydride and 1-pentanol used in the experiment using the following data: Acetic anhydride: 29 mL , sp.gr. 0.811g/mL and MW. 102.09 g/mol 1-Pentanol: 26 mL , sp.gr. 0.916g/mL and MW. 88.15 g/mol Which reactant is in excess? Why it needs to have more excess reactants to drive the reaction forward?

In relation to this question: Compute for the actual moles of acetic anhydride and 1-pentanol used in the experiment using the following data: Acetic anhydride: 29 mL , sp.gr. 0.811g/mL and MW. 102.09 g/mol 1-Pentanol: 26 mL , sp.gr. 0.916g/mL and MW. 88.15 g/mol Which reactant is in excess? Why it needs to have more excess reactants to drive the reaction forward?

Appl Of Ms Excel In Analytical Chemistry

2nd Edition

ISBN:9781285686691

Author:Crouch

Publisher:Crouch

Chapter14: Chromatography

Section: Chapter Questions

Problem 9P

See similar textbooks

Similar questions

In this experiment, the problem is that the volume of the volumetric pipet is not accurately known (only 2 sig figs), so any density calculation will also be limited to 2 sig figs. Calibration increases the number of sig figs from 2 to 4. As a result, the density also increases from 2 to 4 sig figs. Explain how and why this is possible.
DATA Note: Use the videos as references except when data is provided here. Table 1. Selection of Recrystallizing Solvent. Solvents Dissolution at room temperature? (+ or −) Dissolution at elevated temperature? (+ or −) Distilled water - - Acetone + n/a 95% ethanol - + Toluene + n/a Solid sample: Naphthalene Table 2. Mass Measurements. Mass, g Sample solid 0.5021 Empty watch glass 35.7602 Watch glass with recrystallized sample 36.2485 Table 3. Melting Point Determination. Temperature, oC Appearance of Sample in Capillary Tube … Solid 78.4 Solid 79.3 Solid with signs of liquid 79.9 Solid, liquid 80.6 Liquid, solid 81.3 Liquid with signs of solid … Liquid Theoretical Melting Point, oC: 80.2°C (176.4°F) QUESTIONS Which solvent should be used as the recrystallizing solvent? Check if your chosen solvent satisfies all characteristics of a good…
Compute for the actual moles of acetic anhydride and 1-pentanol used in the experiment using the following data: Acetic anhydride: 29 mL , sp.gr. 0.811g/mL and MW. 102.09 g/mol 1-Pentanol: 26 mL , sp.gr. 0.916g/mL and MW. 88.15 g/mol Which reactant is in excess? Why it needs to have more excess reactants to drive the reaction forward?
how would u justify this question? my answer is correct i just do not understand the justification. this is a non graded practice worksheet
Hi, can you check my math? Can percent error be negative, if so what does that mean and how do I explain that for my results? These are calculations for Determining the ksp of Calcium Hydroxide Lab. Thanks!
for a experiment how would you calculate the mmol & Equivalents with MW= 106.42g/mol Amount Used: 42mg Density: 12.02g/mol
There's 1 drink (and you are asked to determine the glucose concentration in the drink in the units of g/100mL. (Why these units? Well, once you have the concentrations in g/100mL you will be able to compare your values with the nutritional values given on the drink bottles’ labels). The sample of the drink was diluted 1/100 (i.e. by a factor of 100). This was an essential step in the method because, without it, the machine used to analyse the glucose concentration (spectrophotometer) would have given an error as the concentration would have been too high for accurate detection. What this means for you is that the dilution factor will need to be taken into consideration in your calculations (remember the aim is to calculate the concentration in the original drink and not in the diluted drink). You measured the concentration of their diluted drink using the spectrophotometer and their results were provided to them in the units mM (millimolar). Glucose Concentration in mM of drink =…
There's 1 drink (and you are asked to determine the glucose concentration in the drink in the units of g/100mL. (Why these units? Well, once you have the concentrations in g/100mL you will be able to compare your values with the nutritional values given on the drink bottles’ labels). The sample of the drink was diluted 1/100 (i.e. by a factor of 100). This was an essential step in the method because, without it, the machine used to analyse the glucose concentration (spectrophotometer) would have given an error as the concentration would have been too high for accurate detection. What this means for you is that the dilution factor will need to be taken into consideration in your calculations (remember the aim is to calculate the concentration in the original drink and not in the diluted drink). You measured the concentration of their diluted drink using the spectrophotometer and their results were provided to them in the units mM (millimolar). Glucose Concentration in mM of drink =…
State and explain one possible source of random error whilst using a pipette.Your answer should justify why this is a random error.
A feedstuff weighing 2 g and moisture content at 5%. When estimating the crude protein, use 82 ml of HC1 (0.01 N) (Plank volume = zero). Calculate i. The percentage of crude protein base on dry matter. ii. The percentage of crude protein base on natural (fresh) material. iii. The percentage of crude protein base on organic matter, when crude ash in the feedstuff is 0.3 g.
Vitamin C Analysis, a student accidentally puts 1.0 g of sodium bicarbonate (NaHCO3) solid into the vitamin sample solution for trial #1 instead of 0.5 g as the procedure instructs. How does this procedural change impact the calculated milligrams of ascorbic acid in the sample?
The answer with a BCA table for both parts would be great, thank in advance for the help. btw, this is a pre test that isn’t graded