Moist hydrogen containing 6 mole percent water is burnt completely in a furnace with 42 % excess air. Calculate the Orsat analysis of the resulting flue gas. Basis = 100 mol of moist hydrogen. Họ + 0.502 --» H0 Select one: O a. Yo2 = 8.24%, yn2 = 75.96%, yh2 = 15.8%, yH20 = 0 % O b. yo2 = 7.28%, yn2 = 92.72%, yH2 = 0%, yH20 = 0 %
Q: Using the information below, calculate the percentage w/V of lidocaine (MM (234-34 g/mol) in…
A:
Q: A 0.157g of a compound containing C, H, N and possibly O, yields 0.213g CO2 and 0.0310g H2O upon…
A: When the given sample burned in excess oxygen carbon dioxide and water are formed. All the hydrogen…
Q: If 2000 mL/min of air was sampled for 30 min at 18 °C and 103 kPa what is the volume occupied in…
A: Given: Volume flow rate of air=2000 mLmin Time=30 min Temperature=18°C=273+18…
Q: Hematite is an iron ore with the following composition: Fe2O3 [MW=159.70]. To make steel, carbon…
A:
Q: Q4: A mixture of gases has the following mass fractions: Co = 30%;N2 = 20%; CH4 = 15%; H2 = 25%; 02…
A:
Q: A sample extracted out of hot gas mixture at a temperature of 240 oC and pressure of 1.3 bar…
A: Given data Gas Kmole of gas SO2 0.0025 N2 2.7 CO2 0.45 Total pressure of sample gas : P…
Q: 2- Heat Decomposition mass Curve of sample S with mass 20.00 mg is shown below. Study the TGA…
A: Given, Mass of sample = 20.00 mg At each step the mass of the sample is getting deducted in a…
Q: QI/Prepare 0.1N of CH,COOH in 500 mL, Specific gravity 1.05 gm/cm and percentage 99.5% ?
A: Pipette out 3 ml concentrated CH3COOH (17.4 N) in a 500 ml volumetric flask and dilute it up to the…
Q: 10.5mL (mw 106) of benzaldehyde and 2.9g(3.63mL, mw 40) of acetone react with 5g of NaOH and 25mL of…
A:
Q: Sodium carbonate is recovered as decahydrate from 1000kg of 5% solution of sodium carbonate in…
A: 1.
Q: .40. Ammonia is burned to form nitric oxide in the following reaction: 4NH3 + 502 - 4NO + 6H2O (a)…
A:
Q: 1. To complete the following table: a. Determine the initial concentrations (molarity) of S2032 and…
A:
Q: Certain amount of pure charcoal (carbon) has to be burnt with supplied natural air. Process engineer…
A: The complete balanced reaction : C + O2(g) → CO2(g) Given in question, Mass of CO2 produced = 5 kg…
Q: Study the tabulated data during an gravimetric analysis of BaSO4 experiment Trial T1 T2 T3 Mass of…
A:
Q: A mixture of methane and air is capable of being ignited only if the mole percent of methane is…
A: Given: Mole percentage of methane= between 5% and 15% Number of mole of methane= 9.0 mole Flowing…
Q: 2- Heat Decomposition mass Curve of sample S with mass 20.00 mg is shown below. Study the TGA…
A: A question based on TGA, which is to be accomplished.
Q: 1. The following data were obtained after the moisture and total ash content determination of acacia…
A: Since you have asked multiple questions, we will solve the first question for you. If you want any…
Q: The %purity of a powdered crude sample of Na2CO3 containing only inert impurities is to be…
A: #(a): Na2CO3 reacts with HCl to produce H2CO3(aq) and NaCl. H2CO3(aq) decomposes further to form…
Q: [References) Describe the preparation of 750 mL of 5.30 M H3PO4 from the commercial reagent that is…
A:
Q: You would like to operate a gasifier with biomass feedstock CHαOβ. The proximate analysis on a dry…
A: Let us,assume the biomass amount =100gm Amount of carbon=50gm Amount of hydrogen=10gm Amount of…
Q: A mixture of methane and air is capable of being ignited only if the mole percent of methane is…
A: Given: air flow rate = 1300 kg/hr mole percent of methane = 6.00 mole % moles of methane in mixture…
Q: "he table and graph below display data from the Fresh 4 Less farm stand in A /19/2020 from…
A: To predict the sales with a certain number of customers using the Lagrange's interpolation formula:…
Q: (a) Water in vadose zone contains chlorobenzene of concentration 40 mg/L. What is the equilibrium…
A: “Since there are multiple questions and it is not mentioned that which one has to be solved so I am…
Q: 150 kg of hexane is burned completely with 35% excess air. Find the complete analysis of the flue…
A: Air mainly composed of nitrogen with 78% and oxygen with 21%. Hexane reaction with O2 (g) and…
Q: How many kilograms (kg) of 20-20-20 soluble fertilizers should you add to a 50 gallon concentrated…
A: 20-20-20 fertilizer refers to a NPK fertilizer having N:P:K = 20:20:20.
Q: A chemist received different mixtures for analysis with the statement that they contained NaOH,…
A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…
Q: Need the theoretical yield for following Starring: 1,4 Pimethoxy Bentene : 0.321 grams Mw=138.14…
A:
Q: A feedstuff weighing 2 g and moisture content at 5%. When estimating the crude protein, use 82 ml of…
A: The amount of acid used in titration can easily be related to the N content of the sample: N(%,…
Q: What would be the effect (+, - or 0) on the calculated Rexp for each of the following? Please…
A: Answers are explained below. The effect on calculated Rexp for each case is as follows:
Q: According to this, find the amount of CO2 absorbed by titration?
A:
Q: A mixt. of 46.32 of pure NaOH ir dinsolved in water and diluted to 1000mL. what vol- of 1-022 N HCA…
A: SOLUTION: Step 1: Neutralization is the process where H+ and OH- react to form water therefore…
Q: Identify the effect of the condition on the indicated parameter. Write increase, decrease, or no…
A: Here,we are measuring heat of reaction by reacting reactants with nitric acid.
Q: The volume of HCI is 100 mL , mass of solid added is 1.008g, moles of solid 0.0276 Mol, mass of HCI…
A: Given: Volume of HCl = 100 mL Mass of solid Added = 1.008 g moles of solid = 0.0276 Mol mass of HCI…
Q: A gas consist of 70% propane and 30% butane by volume. Find the stoichiometric air-to-fuel ratio.…
A: The stoichiometric air-to-fuel ratio will be C --> 23:1
Q: A schematic flow sheet of a process is shown in figure below. The following table gives the…
A:
Q: Molecular weight of a certain volatile liquid which is placed in 225 g flask which has total…
A: According to the question, we need to determine the molecular weight of the volatile sample. Given:…
Q: 1. In the following reaction, 325 mg of 2-hydroxybenzoic acid are reacted with 150 ul of methanol.…
A:
Q: Part A. Write the balanced equation for the reaction that produced the gas in this reaction Trial 1…
A: Given: Partial pressure of water at 23 oC = 21.1 mmHg = 0.0277 atm
Q: A wet pipette was used to transfer 10.00 mL of 1M HNO3 in the determination of ΔHrxn. [magnitude of…
A: Since you have posted multiple questions, we are entitled to answer the first only.
Q: A mixture of KCl and KClO3 weighing 1.92 grams was heated; the dry O2 generated occupied 148 mL at…
A: The mole concept can be used to calculate the moles of reactant or other products. One mole of the…
Q: set up the chemical equation for combustion ethyl alcohol (C2HO) on 15% excess air . show the masses…
A: Chemical Equation for the combustion of Ethyl alcohol is as under C2H5OH + 3O2 --> 2CO2 + 3H2O…
Q: IMOLK Data, Trial 2 Ideal Gas Law-PV=nRT Molarity of HCI (M): Data, Trial 1 3.00M 3.00 M Volume of…
A: Hii there, As there are multiple question posted. we are answering first question. If you need…
Q: A mixture of Al2O3(s) and CuO(s) weighing 18.371 mg was heated under H2(g) at 1 0008C to give 17.462…
A:
Q: 1) 1500 kg mixture contains 15% acetone, 75% water and 10% Acetic acid by weight. a) Calculate the…
A:
Q: 4. Producer gas from bituminous coal (see table below) is burned with 20% excess air. Calculate the…
A:
Q: gangue and copper sulfate is to be leached in a countercurrent multistage extractor using pure water…
A: Solution - According to the question - Given - X0 = 1200 /10000 = 0.12 R0 = 8 / 92 = 0.0869 From…
Q: 2. Show by calculation how you would prepare the following solutions. 2.1 200ml stock solution of 1M…
A: 1 : x Dilution means one part of stock solution is mixed with (x-1) part of solvent.
Step by step
Solved in 7 steps
- (a) Water in vadose zone contains chlorobenzene of concentration 40 mg/L. What is the equilibrium concentration soil air in contact with this solution? (b) An aquifer with porosity 0.3 has distribution coefficient of TCE as 100 L/kg. What fraction of TCE is in aqueous phase and sorbed phase of the soil?A chemist received different mixtures for analysis with the statement that they contained NaOH, NaHCO3, Na2CO3, or compatible mixtures of these substances, together with inert material. From the data given, identify the respective materials, and calculate the percentage of each component. 1.000g samples and 0.2500N HCl were used in all cases. (A) For Sample W: With PP, 24.32ml was used. A duplicate sample required 48.64ml with MO. (B). For Sample X: The addition of PP caused no color change. With MO, 38.47ml of the acid was required. (C). For Sample Y: To cause a color change in the cold with PP, 15.29ml of the acid was necessary, and an additional 33.19ml was required for complete neutralization. (D) For Sample Z: The sample was titrated with acid until the pink of PP disappeared; this process required 39.96ml. On adding an excess of the acid, boiling, and titrating back with alkali, it was found that the alkali was exactly equivalent to the excess acid added.Method of separation/chemical reaction (with the brief process) of 3 KG's OF SODIUM BORATE AND 1.5 KG's HYDROCHLORIC ACID
- Six iron tablets containing FeSO4.7H2O were dissolved in 100-ml of 0.1M HNO3 with gentle heating. All of the Fe2+ is converted to Fe3+ by the strong oxidizing conditions. After the solution had cooled to room temperature , 2.5-ml of 35wt% NH4OH was added. The precipitate Fe2O3-xH2O that was filtered weighed 0.345g. Thermogravimetric analysis of the crude product showed a 10.5% weight loss . A. How many waters of hydration were in the precipitate B. How much iron is present in each tabletAleks data for AgBrO3 is 5.38 x 10^-5A sample of an iron ore was prepared for Fe3+ analysis as following: 3.4g of the sample was added anddissolved in acid environment then diluted to 250 mL using volumetric flask. After that, 10 mL of the resultingsolution was transferred by pipet to a 50-mL volumetric flask and continue to be diluted. The scientists foundout that this solution gives the concentration of Fe3+ as 2.3 mg/L. Find the weight percentage of Fe3+ in theoriginal sample.
- Hexanoic acid was added to an immiscible biphasic solvent sysem, water and CCl4 at 20.0OC and the equilibrium concentrations of hexanoic acid were determined to be 3.66 g/L in H2O and 67.0 g/L in CCl4. Caluclate the distrubution coeffiecent (D1) of hexanoic acid in CCl4 with respect to water.1. Sodium carbonate is recovered as decahydrate from 1000kg of 5% solution of sodium carbonate in water. If it is desired that 95% of Na2CO3 is to be recovered as decahydrate by cooling to 278 K, determine the following: a) the mass of water evaporated (b) the mass of crystals obtained (Na2CO3 ∙ 10H2O). The solubility of Na2CO3 in water at 278K is 9.0% (weight) 2. A copra batch contains 44% oil and is to be extracted with n-hexane. The extracted meal contains 0.07 kg of oil/kg oil free matter and the mass fraction of n-hexane in it is 0.05. The extract contains 49% n- hexane. If 10,000 kg of copra are to be processed, how many kg of n-hexane are required and the determine the amount of extract. 3. Absorption of sulphur dioxide is carried out in a packed tower. Gas containing 14.8% sulphur dioxide and the rest inert gases enters the tower while the leaving gases contains 1% sulphur dioxide. Water flows at the rate of 1m3/min. The tower handles 7380 m3/hr of gas at 303K and 1 bar. Find…A 100 g soil containing 20% smectitie mineral matter was mixed with 150 mL solution containing 0.10 M Pb. CEC of pure smectitie is 110 emol(+)/kg. CEC of the soil (cmol(+)/kg) is:
- If to a solution of NaOH, in water and ethanol (20 ° C) 3 mmol of A (106.11 g / mol) and 2 mmol of B (58.06 g/ mol) and stirred magnetically for 10 minutes. After the reaction is completed, we proceed to isolate (work- up) and purify at C (246.29 g/ mol) yielding 0.300 g of the pure product. Calculate the% return for C showing his work. please show every single step and calculationsDetermine the percentage Fe in a sample of limonite from the following data:Sample : 0.5000g ; KMnO4 used = 50.00 ml ; 1.000ml of KMnO4 is equivalent 0.005317 g Fe,FeSO4 used = 6.00 ml; 1.000ml FeSO4 is equivalent 0.009200 g FeO ( ans 44.59 %)In the synthesis of hydrocarbons, the carbon source is carbon dioxide. Although the CO2 concentra?on in the atmosphere raises at a drama?c speed, point sources are probably the easier sources for a PtX process. Iden?fy 3 possible point sources, explain why CO2 is formed and what challenges each of the three CO2 streams presents