2- Heat Decomposition mass Curve of sample S with mass 20.00 mg is shown below. Studythe TGA thermogram and answer the following questions: -10012.4% A19.2% B8030.0% C604020200.400600.8001000Temp /Ca- Calculate the amount of the remaining sample in mg at steps1- A2- Bb- How much the residue of the sample in mg after the heat decomposition has completed?

Given, Mass of sample = 20.00 mg At each step the mass of the sample is getting deducted in a…

2- Heat Decomposition mass Curve of sample S with mass 20.00 mg is shown below. Study the TGA thermogram and answer the following questions: - 100 12.4% A 19.2% B 30.0% 200. 400 60. 800 1000 Temp IC a- Calculate the amount of the remaining sample in mg at steps 1- A 2- B b- How much the residue of the sample in mg after the heat decomposition has completed?

2- Heat Decomposition mass Curve of sample S with mass 20.00 mg is shown below. Study the TGA thermogram and answer the following questions: - 100 12.4% A 19.2% B 30.0% 200. 400 60. 800 1000 Temp IC a- Calculate the amount of the remaining sample in mg at steps 1- A 2- B b- How much the residue of the sample in mg after the heat decomposition has completed?

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter33: High-performance Liquid Chromatography

Section: Chapter Questions

Problem 33.12QAP

See similar textbooks

Similar questions

What is ΔHsys for a reaction at 16.9 °C with ΔSsurr = -159 J mol-1 K-1 ? Express your answer in kJ mol-1 to at least two significant figures. (Please type answer no write by hend)
Mass of crude Acetanilide = 0.508 Mass of filter paper = 0.800g Filter paper + pure Acetanilide = 1.153g Mass of pure Acetanilide = ? % recovery = ? Mpt of recrystallized Acetanilide =112 C – 114 C Mpt of crude Acetanilide = 97 C – 110 C
The concentration of purified OXA-M290 is tested with a BCA assay. Serial dilutions of a bovine serum albumin (BSA) stock solution are prepared, then pipetted into a 96-well plate; each dilution of the BSA standard is tested in triplicate. Then, bicinchoninic acid and Cu2+ ions are added to all of the wells of the plate. After incubating the plate for 1 hour, a microplate reader is used to measure the absorbance of all of the wells in the plate at 560 nm. This generates the following data: BSA conc. (μg/mL), Replicate 1 Absorbance, Replicate 2 Absorbance, Replicate 3 Absorbance 40, 1.360, 1.403, 1.481 20, 0.750, 0.745, 0.810 10, 0.380, 0.344, 0.398 5, 0.198, 0.160, 0.183 2.5, 0.090, 0.100, 0.085 1.25, 0.038, 0.043, 0.051 0.625, 0.024, 0.028, 0.019 Prepare a calibration curve using these data. You can use Excel, R, SPSS or an equivalent graphing software. In this graph, plot absorbance (y-axis) against the concentration of the protein standard (x-axis). Calculate and plot…
Louie performed paper chromatography to identify which among the four availablereference mixtures — WAR, OFF, YIN, MEW — have the same components as hisunknown sample, GUN. He spotted the standards and the sample in a Whatman No. 1filter paper, which he placed in a developing chamber containing 3% KCl. After 20minutes, Louie obtained the chromatogram below, immediately noting that the distancetravelled by the solvent from the origin is 79.0 mm. On the other hand, the distances (incm) traveled by the developed spots were tabulated as follows.(see attached) Questions: 1. Is the type of paper chromatography performed normal or reversed? Why?2. Calculate the Rf of the spots from the samples. Report your answers in four decimal places.
The gravimetric factor used to express CoCBr6·H20 in a sample that is finally weighed as PbClBr is choose below: FW PbClBr / 6 x FW CoCBr6·H20 FW CoCBr6·H20 / FW PbClBr FW CoCBr6·H20 / 6 x FW PbClBr 6 x FW PbClBr / FW CoCBr6·H20
A sample of anhydrous Na2CO3 (FM = 105.989) is suspected to be contaminated with eitherNaHCO3 (FM = 84.007) or NaOH (FM = 39.997) To verify the suspicion, a 0.7483 g sample was dissolved to prepare a 50.00 mL solution, and a 10.00 mL aliquot was taken to prepare a 100 mL solution, where 25.00 mL was analyzed using single flask method. If the sample requires 27.50 mL of standard 0.0125 N HCl to reach the phenolphthalein endpoint and another 28.40 mL to reach the bromcresol green endpoint, calculate the percentagecomposition (in %w/w) of all the basic components in the sample.
Study the tabulated data during an gravimetric analysis of BaSO4 experiment Trial T1 T2 T3 Mass of sample (g) 1.0040 1.0100 1.0050 Constant weight of empty crucible (g) 10.2453 10.2454 10.2454 Constant weight after ignition (g) 10.3253 10.3252 10.3253 1. Calculate the mean mass of precipitate as BaSO4 a. 0.0799 g b. 0.0800 c. 0.08 g 2. Calculate the mean weight of sulphate (MM BaSO4 = 233.39 g/mol, So42- = 176 g/mol)? a. 0.0603 g b. 0.06 g c. 0.06025 g 3. Calculate the mean % SO42- in the sample a. 6.00% b. 5.991% c. 5.9908%
5.00 mL of stock solution is diluted to 25.00 mL, producing solution ALPHA. 10.00 mL of solution ALPHA is diluted to 25.00 mL, resulting in solution BETA. 10.00 mL of solution BETA is then diluted to 25.00 mL, producing solution GAMMA. dilution factor for ALPHA from stock solution = 0.167 dilution factor for BETA from ALPHA solution = 0.0476 part c and d?
Suppose you have a soil that is made up of 10% organic matter with CEC = 200 cmol/kg, 40% kaolinitewith CEC = 10 cmol/kg, and 50% vermiculite with CEC = 100 cmol/kg.1- Calculate the overall CEC of the soil by taking a weighted average of the three soil components.2- What percentage of the overall CEC is contributed by the organic matter? How does that numbercompare to the 10% of the soil itself that is organic?
Show ALL calculations pls. Don't reject if you dont know how to answer I need this. a. What are the average values for vph and vmo? Include calculation of net volume and errorsb. What is/are the component/s of the soda ash sample? c. Calculate the percent composition of the component/s. No need to include error propagation, but you still need to apply Significant Figure rules.
Aleks data for PbCO3 is 7.40 x 10^-14.