Pair of beams (AB) and (CDE) are connected by cable BC and subjected to the concentrated and distributed loads shown in the figure. Do the following: a. Draw the free body diagram of each beam b. Determine the force in cable BC c. Determine the magnitudes of the reactions at A, D, and E for the pair of beams 30 kN 40 kN/m 55° 0.5 m. 1.5 m * 1.5m 10 kN.m 20 kN/m 2m 30 2 m

Pair of beams (AB) and (CDE) are connected by cable BC and subjected to the concentrated and distributed loads shown in the figure. Do the following: a. Draw the free body diagram of each beam b. Determine the force in cable BC c. Determine the magnitudes of the reactions at A, D, and E for the pair of beams 30 kN 40 kN/m 55° 0.5 m. 1.5 m * 1.5m 10 kN.m 20 kN/m 2m 30 2 m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter10: Statically Indeterminate Beams

Section: Chapter Questions

Problem 10.4.32P: Two identical, simply supported beams AB and CD are placed so that they cross each other at their...

See similar textbooks

Similar questions

A cylindrical brick chimney of height H weighs w = 825 lb/ft of height (see figure). The inner and outer diameters are d1= 3 ft and d2= 4 ft, respectively. The wind pressure against the side of the chimney is p = 10 lb/ft2 of projected area. Determine the maximum height H if there is to be no tension in the brickwork.
A fixed-end beam AB supports a uniform load of intensity q = 75 lb/ft acting over part of the span. Assume that EI = 300kip-ft2. Calculate the reactions at A and B. Find the maximum displacement and its location. Repeat part (a) if the distributed load is applied from A to B.
A temporary wood flume serving as a channel for irrigation water is shown in the figure. The vertical boards forming the sides of the flume are sunk in the ground, which provides a fixed support. The top of the flume is held by tic rods that are tightened so that there is no deflection of the boards at that point. Thus, the vertical boards may be modeled as a beam AB, supported and loaded as shown in the last part of the figure. Assuming that the thickness t of the boards is 1,5 in., the depth d of the water is 40 in., and the height h to the tie rods is 50 in., what is the maximum bending stress in the boards? Hint: The numerically largest bending moment occurs at the fixed support.
The beam ABC shown in the figure is simply supported at A and B and has an overhang from B to C. The loads consist of a horizontal force P1= 4,0 kN acting at the end of a vertical arm and a vertical force P2= 8.0 kN acting at the end of the overhang, Determine the shear force Fand bending moment M at a cross section located 3,0 m from the left-hand support. Note: Disregard the widths of the beam and vertical arm and use centerline dimensions when making calculations, Find the value of load A that results in V = 0 at a cross section located 2.0 m from the left-hand support. If P2= 8.0 kN, find the value of load P1that results in M = 0 at a cross section located 2,0 m from the left-hand support.
An S6 × 12.5 steel cantilever beam AB is supported by a steel tic rod at B as shown. The tie rod is just taut when a roller support is added at Cat a distance s to the left of £, then the distributed load q is applied to beam segment AC, Assume E = 30 × 106 psi and neglect the self-weight of the beam and tie rod. Sec Table F-2(a) in Appendix F for the properties of the S-shape beam. (a) What value of uniform load q will, if exceeded, result in buckling of the tie rod if L1, =6 ft, s = 2 ft, H = 3 ft, and d = 0.25 in.? (b) What minimum beam moment of inertia ibis required to prevent buckling of the tie rod if q = 200 lb/ft, L1, = 6 ft, H = 3 ft, d = 0.25 in., and s = 2 ft? (c) For what distance s will the tic rod be just on the verge of buckling if q = 200 lb/ft, L1= 6 ft, M = 3 ft, and d = 0.25 in.?
.10 A built-up bourn supporting a condominium balcony is made up of a structural T (one half of a W 200 x 31.3) for the top flange and web and two angles (2 L 2 / b / 6.4. long legal back-lo-backl lot the bottom flange and web. as shown. The beam is subjected to a bending moment .1/ having its vector at an angle ft lo the z axis (see figure). Determine the or ion ta I ion of the neutral axis and calculate the maximum tensile stress ir, and maximum compressive stress tr. in ".he beam. .Assume that 9 = 30°andM = 15 kN · m. Use the numerical properties: c =4.111mm, c2 =4.169 mm, of = 134 mm, I, = 76 mm, A = 4144 mm 3 =3.88 X 106 mm 4, and = 34.18 X 10 mm 4.
Two identical, simply supported beams AB and CD are placed so that they cross each other at their midpoints (sec figure). Before the uniform load is applied, the beams just touch each other at the crossing point. Determine the maximum bending moments (mab)max* and (MCD)max beams AB and CD, respectively, due to the uniform load if the intensity of the load is q = 6.4 kN/m and the length of each beam is L = 4 m.
In the figure, A 10 meters bar of megligible weight supports a uniform load of w1=5N from A to the center and a varying load of w2=10N from center to B, and with a concentrated load of F= 50N distance from 3 meters from A. An additional Moment of 15 N/m is acting on B. Calculate the reaction @ A and @ B
A flanged wooden shape is used to support the loads shown on the beam. The dimensions of the shape are shown in the second figure. Assume LAB = 9 ft, LBC = 3 ft, LCD = 4 ft, LDE = 4 ft, PC = 2150 lb, PE = 2260 lb, wAB = 650 lb/ft, b1 = 11 in., b2 = 2 in., b3 = 7 in., d1 = 2 in., d2 = 5 in., d3 = 2 in. Consider the entire 20-ft length of the beam and determine:(a) the maximum tension bending stress σT at any location along the beam, and(b) the maximum compression bending stress σC at any location along the beam.
The rigid beam ACE is fixed by both sides as shown in figure, if F1 = 300 kN and F2 = 150 kN. Find the reactions Ra and Rb. Take S = 3.5 mm and E=200 (GPa):
A beam 12m long is resting on supports at each end. If the beam carries loads at the positions shown in figure, what are the reactive forces at the supports? Neglect the weight of the beam.
A 20.0-m-long uniform beam weighing 560 N rests on walls A and B, as shown in the figure (Figure 1). a) Find the maximum weight of a person who can walk to the extreme end D without tipping the beam. b) Find the forces that the walls A and B exert on the beam when the person is standing at D c) Find the forces that the walls A and B exert on the beam when the person is standing at a point 2.8 m to the right of B. d) Find the forces that the walls A and B exert on the beam when the person is standing 1.5 m to the right of A.