Please solve this question in handwriting step by step. PROBLEM 17.62Disk B has an initial angular velocity o, when it is brought into contactwith disk A which is at rest. Show that the final angular velocity of disk Bdepends only on 0, and the ratio of the massesAandm3of the twoBdisks.BhpArchitecturalCOME

Answered: Image /qna-images/answer/f099f3a3-9c53-4beb-8b7c-0404051e6c7a.jpg

PROBLEM 17.62 Disk B has an initial angular velocity o, when it is brought into c with disk A which is at rest. Show that the final angular velocity of depends only on 0, and the ratio of the masses m, and m; of th B. disks.

PROBLEM 17.62 Disk B has an initial angular velocity o, when it is brought into c with disk A which is at rest. Show that the final angular velocity of depends only on 0, and the ratio of the masses m, and m; of th B. disks.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the helicopter shown; a vertical tail propeller is used to pre- vent rotation of the cab as the speed of the main blades is changed. Assuming that the tail propeller is not operating determine the final angular velocity of the cab after the speed of the main blades has been changed from I80 to 240 rpm. (The speed of the main blades is measured relative to the cab, and the cab has a centroidal moment of inertia of 650 lb.ft.s2. Each of the four main blades is assumed to be a slender rod 14 ft weighing 55 lb.)
A long ladder of length l, mass m, and centroidal mass moment of inertia I is placed against a house at an angle 0=0O. Knowing that the ladder is released from rest, determine the angular velocity of the ladder when 0=02. Assume the ladder can slide freely on the horizontal ground and on the vertical wall.
The upper and lower ends of the arms are pivoted on the axis of the governor has equal arms of length 44cm. The extension arms of the lower links are each 10cm long and parallel to the axis.When the governor at minimum and maximum position, the radii of rotation of the balls are 17cm and 24cm respectively. The mass of each ball is 10 kg and the mass of the central load is 102 kg. Determine : 1.The range of angular speed of the governor and identify the type of governor 2.Draw the line diagram when the governor at minimum and maximum position
A 5.32-kg disk A of radius 0.445 m initially rotating counter-clockwise at 436 rev/min is engaged with a 6.72-kg disk B of radius 0.275 m initially rotating clockwise at 528 rev/min, where the moment of inertia of a disk is given as I = ½ mi?. Determine their combined angular speed (in rpm) and direction of rotation after the meshing of the two disks. Remember to show clearly the equations that you use!!'
The 4-kg rod AB is attached to a collar of negligible mass at A and to a flywheel at B. The flywheel has a mass of 16 kg and a radius of gyration of 180 mm. Knowing that in the position shown the angular velocity of the flywheel is 60 rpm clockwise, determine the velocity of the flywheel when point B is directly below C.
The rotor of an electric motor has a mass of 25 kg, and it is observed that 4.2 min is required for the rotor to coast to rest from an angular velocity of 3600 rpm. Knowing that kinetic friction produces a couple of magnitude 1.2 N.m, determine the centroidal radius of gyration for the rotor.
A semicircular panel with a radius r is attached with hinges to a circular plate with a radius r and initially is held in the vertical position as shown. The plate and the panel are made of the same material and have the same thickness. Knowing that the entire assembly is rotating freely with an initial angular velocity of w0 , determine the angular velocity of the assembly after the panel has been released and comes to rest against the plate.
A collar with a mass of 1 kg is rigidly attached to a slender rod AB of mass 3 kg and length L = 600 mm. The rod is released from rest in the position shown. Determine the distance d for which the angular velocity of the rod is maximum after it has rotated through 90°.
A 1200-kg satellite designed to study the sun has an angular velocity of w0 = (0.050 rad/s)i + (0.075 rad/s)k when two small jets are activated at A and B in a direction parallel to the y axis. Knowing that the coordinate axes are principal centroidal axes, that the radii of gyration of the satellite are and that each jet produces a 50-N thrust, determine (a ) the required operating time of each jet if the angular velocity of the satellite is to be reduced to zero, (b ) the resulting change in the velocity of the mass center G.
A 7.5 kg disk A radius of 0.6 m initially rotating clockwise at 300 rev/min is engaged with an 8.5 kg disk B of radius 0.4 m initially rotating counter clockwise at 700 rev/min, where the moment of inertia of a disk is given as I=1/2mr^2. Determine their combined angular speed (in rpm) and direction after the meshing of the two disks.
A uniform square plate with side a= 300 mm is hinged at points A and B to a clevis that rotates with a constant angular velocity w about a vertical axis. Determine (a) the value of w for which the plate forms a constant angle β= 60° with the horizontal x axis, (b) the largest value of w for which the plate remains vertical (β= 90°).
A driver starts his car with the door on the passenger’s side wide open ( _ θ = 0). The 100-lb door has a centroidal radius of gyration k = 12 in. and its mass center is located at a distance r = 20 in. from its vertical axis of rotation. Knowing that the driver maintains a constant acceleration of 4 ft/s2 , determine the angular velocity of the door as it slams shut (θ = 90°).