Problem 2: A steel tube having an outer diameter of 2.5 in. is used to transmit 10 hp when turning at 30 rev/min. Determine the inner diameter d of the tube to the nearest 1/8 in. if the allowable shear stress is talow = 12 ksi.

Problem 2: A steel tube having an outer diameter of 2.5 in. is used to transmit 10 hp when turning at 30 rev/min. Determine the inner diameter d of the tube to the nearest 1/8 in. if the allowable shear stress is talow = 12 ksi.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Determine the maximum shearing stress in kPa of a helical spring composed of 18 turns and 25 mm wire…

A: GIVEN DATA MEAN COIL DIAMETER D=2*100= 200mm WIRE DIAMETER d=25mm SUPPORTING LOAD W =1500N WE HAVE…

Q: Determine the dimensions of a hollow shaft with a diameter ratio of 3:4 which is to transmit 60 kW…

A: Given information: Hollow shaft with diameter ratio 3:4That is Inside DiameterOutside Diameter =…

Q: (a) A circular shaft used for transmission is 510mm in length and 50mm in external diameter. It is…

Q: Determine the torsional shear stress in a solid circular shaft having a diameter of 1.25 in. that is…

Q: Q3: The shaft consists of three concentric tubes, each made from the same material and having inner…

A: Handwriting.jpg

Q: Q3: Determine the dimensions of a hollow shaft with a diameter ratio of 3:4 which is to transmit 60…

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 212 mm and a…

Q: While a steel shaft of the cross section shown rotates at 110 rpm, a stroboscopic measurement…

A: given datavpm=110 rpmangle of twist=2°length=4mG=77.2 Gpa10 determine:power transmitted

Q: PROBLEM 3.1 Determine the torque T which causes a maximum shear stress of 70 MPa in the steel…

Q: Problem No. 3. The compound shaft has the following properties: G in both Segment 1 Segment 1…

A: Calculate the inner diameter of the shaft 1. d1=D1-2t1 Here, D1 is the outer diameter of shaft 1, d1…

Q: Determine the internal torques, T₁ and T2, in segments (1) and (2), respectively. Use the internal…

Q: Two motors deliver 119 hp each at 1000 rpm to shafts at A and D. The shaft transmits torque through…

A: Data given- Motor deliver = 119 hp N = 1000 rpm Shear modulus = 11 × 103 ksi

Q: 3. A motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B…

Q: ft consists of three concentric tubes, each made from the same material and having inner and outer…

A: Given, Torque, T=800 N.m For inner tube, ri=20mm, r0=25mm For center tube, ri=26mm, r0=30mm For…

Q: Problem #1. The 20-mm diameter shaft is subjected to torques as shown. The shaft is made of steel…

Q: A 500 mm pulley running at 400 rpm drives another pulley of the same diameter by means of a 12 mm…

Q: Q.1) Two torques are applied to the solid bronze (G= 6500 ksi) shafts of a gear system shown below.…

A: Consider the given figure. For the shaft AB, in equilibrium condition the torque acting on the gear…

Q: A tubular steel [G = 79 GPa] shaft with an outside diameter of D = 89 mm and a wall thickness of t =…

A: Given Data The modulus of rigidity is: G=80 GPa The outside diameter is: D=89 mm The thickness of…

Q: 4.1. Draw the diagram of internal torque applied for each cross-section of the compound shaft 4.2.…

A: As par answering guidelines I can answer 1st 3 subparts at a time.If you want other please post it…

Q: An impeller mechanism in a granular material mixing tank is shown. The shaft is hollow with a 2.25"…

A: Given, ro = 2.25" θmax=6o τmax=10 ksi G = 11000 ksi

Q: A steel tube having an outer diameter of 2.5 in. is used to transmit 9 hp when turning at 27…

A: Given data: The outer diameter, do = 2.5 in. The power transmitted, P = 9 hp. The turning…

Q: Select the size of a hollow steel shaft necessary to transmit 150 hp at 250 rpm without exceeding an…

A: Given data, Power=150hp speed=250 rpm shear stress=4.7ksi angle of twist =0.35°…

Q: A solid steel shaft ABC with diameter d = 40 mm is driven at A by a motor that transmits 75 kW to…

Q: The driveshaft of an automobile is being designed to transmit 203 hp at 2940 rpm. Determine the…

Q: A solid steel shaft ABC with diameter d =40 mm is driven at A by a motor that transmits 75 kW to the…

Q: Q3-C- The 304 stainless steel shaft with modulus of rigidity 75 GPa and 3 m long has an outer…

Q: 2. The solid 50-mm-diameter shaft is used to transmit the torques applied to the gears. Determine…

A: Given Data D=50 mm

Q: Problem No. 4. A compound shaft consists of two pipe segments has the following properties: SET…

A: Segment 2 from set c Torque = Tc = 34 KN.m = 34 X 106 N.mm Outside Diameter = D2 = 230 mm Wall…

Q: When drilling a well at a constant angular velocity, the bottom end of the drill pipe encounters a…

A: Given, Torsional Resistance at A = TA Distributed torque = (0,0) at B and (tA,L) at B Outer radii…

Q: Determine the power in kilowatts transmitted by the solid shaft if the radius is 7.5mm and it…

Q: A solid circular drive shaft of length = 0.5 m, is to be designed to transmit up to 45000 W at 1800…

Q: A steel shaft rotates at 600 rev/min and transmits torque of 30 N.m through a spur gear which has…

A: Factor of safety can not be less than 1 during designing of any part which is in dynamics. As…

Q: A steel shaft of diameter 50 mm is used to transmit the power of 450 W at 2000 rpm. Determine the…

A: Given data: - The diameter of the shaft is d = 50 mm. The power transmitted by the shaft is P =…

Q: Q4 (DÖÇ-1) For the given gear-shaft system failure shear stress for the shafts is 90 MPa, If the…

A: FOS = FAILURE SHEAR STRESSALLOWABLE SHEAR STRESS 1.5 = 90τallowτallow = 60 MPa d2 = 60 mm = 0.06 m…

Q: The motor on the left provides a torque of 5500 N•m to the gear shaft shown. The motor runs machines…

Q: shaft

Q: PROBLEM 3.2 Determine the maximum shear stress caused by a torque of magnitude T= 800 Nm. [Ans. 87.3…

Q: 6. The motor delivers 40 hp to the 304 stainless steel shaft while it rotates at 20 Hz. The shaft is…

Q: For a given maximum average shear stress, determine the factor by which the torque-carrying capacity…

A: The mean area without reversed position Am=(1.10)1.75-π(0.55)22=1.4498 in2 The mean area at reversed…

Q: The solid and hollow shafts are each subjected to the torque T. In each case, sketch the shear…

A: The solid shaft is subjected to torque T in a clockwise direction. The shear stress is calculated…

Q: The compound shaft, consisting of steel and aluminium segments, carries the two torques shown in the…

Q: The shaft consists of three concentric tubes, each made from the same material and having inner and…

A: Given, Torque, T=800N.m For Inner tube: ri= 20mm, ro= 25 mm. For Center tube: ri= 26 mm, ro = 30 mm.…

Q: Consider two steel shafts CFG and HJ of diameters 50 mm and 70 mm respectively as shown in fig. The…

Q: Q3: The shaft consists of three concentric tubes, each made from the same material and having inner…

A: GIVEN:Torque T= 800N-mLength of shaft=2mNo. of concentric tubes=3 Outer tube radius,…

Q: Determine the maximum shearing stress in MPa of a helical spring composed of 20 turns and 19 mm wire…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

Please answer by moment area method

Problem 2: A steel tube having an outer diameter of 2.5 in. is used to transmit 10 hp when
turning at 30 rev/min. Determine the inner diameter d of the tube to the nearest 1/8 in. if
the allowable shear stress is talow = 12 ksi.
2.5 in.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q2: A solid steel shaft A of 60 mm diameter rotates at 300 rev/min. Find the greatest power that can be transmitted for a limiting shearing stress of 60 MN/m2 in the steel. It is proposed to replace A by a hollow shaft B, of the Same external diameter but with a limiting shearing stress of 75 MN/m2 . Determine the internal diameter of B to transmit the same power at the same speed.
Determine the diameter of a solid steel shaft which will transmit 112.5 kW at 200 rpm. Also determine the length of the shaft if the twist must not exceed 1.5o over the entire length. The maximum shear stress is limited to 55 N/mm2. Take the value of modulus of rigidity = 8 x 104 N/mm2.
The motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B and 2000 hp is removed by gear C. 1.) Determine the maximum shear stress in the shaft in ksi. (Answer in 2 decimal places) 2.) Determine the angle of twist in degrees of end D relative to end A. Use G = 12 x 106 psi for steel, and assume that friction at bearing D is negligible. (Answer in 3 decimal places)
A steel tube having an outer diameter of 2.5 in. is used to transmit 9 hp when turning at 27 rev>min. Determine the inner diameter d of the tube to the nearest 1 8 in. if the allowable shear stress is tallow = 10 ksi.
Problem: 2 A solid shaft is transmitting 9 KW at 550 r.p.m. Determine the diameter of the shaft if the maximum torque transmitted exceeds the mean torque by 20%. Take the maximum allowable shear stress as 78 MPa.
Q: Part A: Determine the absolute maximum shear stress in the shaft. Part B: Determine the angle of twist of end EE of the shaft relative to BB. Given: The turbine develops 150 kW of power, which is transmitted to the gears such that CC receives 70% and DD receives 30%. The rotation of the 100-mm diameter A-36 steel shaft is ωomega = 600 rev/min . The journal bearing at EE allows the shaft to turn freely about its axis. The shear modulus of elasticity for A-36 steel is 75 GPa.
A hollow steel shaft of length 1.75 m transmits 2000 kW of power at a speed of150 rev/min. The inside diameter is to be 0.75 times the outside diameter. Themaximum allowable torsional shear stress for the steel is 130 MN/m2and themodulus of rigidity (G) for the steel is 83 GN/m2. Given that a factor of safety of2 is required for the shaft, determine:i) the torque acting on the shaft;ii) the required external and internal diameters for the shaft; iii) the torsional shear stress set-up in the shaft material at the inside surfaceof the hollow shaft, and sketch the stress distribution through the shaftwall;iv) the angle of twist (in degrees) due to the torque.
tubular steel [G = 80 GPa] shaft is being designed to transmit 150 kW at 30 Hz. The maximum shear stress in the shaft must not exceed 80 MPa and the angle of twist is not to exceed 6° in a 4-m length. Determine the minimum permissible outside diameter if the ratio of the inside diameter to the outside diameter is 0.80.
The disc clutch of an automobile is carried on a 2-inch 6-splined shaft and not to slide under load. The nominal dimensions are as follows: b = 0.25 D; t = 0.075 D and d = 0.85 D. The hub length of 150 % of shaft diameter. Determine the total horsepower transmitted at 3,600 rpm, if the yield strength of the shaft is 1,400 psi
Torsion Problem 6.0 A solid steel shaft is to transmit 5 hp from the motor to which it is attached. If the shaft rotates at w=160rpm and the steel has an allowable shear stress T=14 ksi, determine the required diameter of the shaft.
Calculate the torque T: i. if the shear stress of the brass sleeve in section AB is limited to τb = 70 MPa.ii. if the shear stress of the steel shaft in section BC is limited to τs = 110 MPa.
A solid steel shaft ABC with diameter d = 40 mm is driven at A by a motor that transmits 75 kW to the shaft at 15 Hz. The gears at B and C drive machinery requiring power equal to 50 kW and 25 kW, respectively. Compute the maximum shear stress and angle of twist in the shaft between the motor at A and the gear at C. Assume that G = 75 GPa.