Q// A (300mm) diameter of pipe, if the discharge (90 L/sec), nozzle diameter (75mm) and pipe length from (1 to 2) was (100m) Determine the length of pipe from (2 to 3), and the pressure at point (2). (e=0.026mm, v =1.13 10“ m³/sec). Fig(1).

Q// A (300mm) diameter of pipe, if the discharge (90 L/sec), nozzle diameter (75mm) and pipe length from (1 to 2) was (100m) Determine the length of pipe from (2 to 3), and the pressure at point (2). (e=0.026mm, v =1.13 10“ m³/sec). Fig(1).

Name: QI/ A (300mm) diameter of pipe, if the discharge (90 L/sec), nozzle d
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: QI/ A (300mm) diameter of pipe, if the discharge (90 L/sec), nozzle diameter (75mm) and pipelength from (1 to 2) was (100m) Determine the length of pipe from (2 to 3), and the pressure atpoint (2). (e=0.026mm, v =1.13* 10“ m²/sec). Fig(1).6m23mFig.(

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 30-cm by 15-cm Venturi meter is mounted on a vertical pipe with the flow upward. One hundred twenty-six (126) liters per second of oil (s.g. = 0.80) flows through the pipe. The throat section is 15cm above the upstream section. If Cv=0.957, what is the difference in pressure between the inlet and the throat?
Oil of viscosity 10E-3 Pa-s and specific gravity 0.90, flows through 60 m of 100mm diameter pipe and the pressure drop 13.8 kPa. What will be the pressure drop for a second oil of viscosity 30E-3 Pa.s and the specific gravity 0.95 flowing at the same rate through the pipe? Assume the pipe wall to be smooth.A. 19.4 kPaB. 98.7 kPaC. 142.2 kPaD. 192.5 kPa
The following data were obtained for the flow of 20°C water at20 m3/h through a badly corroded 5-cm-diameter pipe thatslopes downward at an angle of 8°: p1 = 420 kPa, z1 = 12 m,p2 = 250 kPa, z2 = 3 m. Estimate (a) the roughness ratio ofthe pipe and (b) the percentage change in a head loss if thepipe were smooth and the flow rate the same.
P7.) A pipe system, connecting two reservoirs whose difference in water surface elevation is 13 m, consists of 320 m of 600 mm diameter pipe (pipe 1), branching into 640 m of 300 mm diameter pipe (pipe 2) and 640 m of 450 mm diameter pipe (pipe 3) in parallel, which join again to a single 600 mm diameter line 1300 m long (pipe 3). Assuming f = 0.032 for all pipes, determine the flow rate in each pipe. Subject: fluid mechanic Lesson: *Conservation of Energy *Fluid Flow in Pipes
A 25cm circular pipe carries 0.16m3 /sec of water under a pressure of 200Pa. The pipe islaid at an elevation of 10.71m above the mean sea level (MSL) of Ibadan. What is theenergy head measured with respect to the MSL? If = 9810N/m3 (9.81KN/m3).
Three pipes connected in series with lengths L1 = L2 = L3 = 150 m and diameters D1 =75 mm, D2 = 50 mm, D3 = 25 mm. The discharge at the 25mm pipe = 200 lps, kinematic viscosity = 1.12 x 10-6 m2/s and ε = 0.35 mm. Using Colebrook and Darcy-Weisbach Formula, determine the following:a. relative roughness of the 25mm pipeb. roughness coefficient of 75mm pipec. head loss of 50 mm pipe
Paolo owns a hydroelectric power generating system as shown in HG008. Water flows from an upper reservoir to a lower one passing through a turbine at the rate of 150 lps. The total length of pipe connecting the two reservoir is 100 m. The pipe diameter is 250 mm and the Hazen – Williams coefficient is 120. The water surface elevations of reservoirs 1 and 2 are 197 m and 50 m, respectively. Find the velocity of flow in pipe in m/s.
Find the pressure at point 2 given the isometric drawing of the commercial steel pipeline indicating the straight pipes length and with the following data below:Loss coefficients:• check valve, k = 5.0• gate valves, k = 0.20• elbows, k = 0.75• flowmeter, k = 13.0Pump flowrate = 10 m3/hrFluid power adding by pump = 3.7 HPPressure at point 1 = 60 kPagPipe inside diameter = 50mmViscosity = 0.17 Pa.sSpecific gravity = 0.89Pipe inside surface roughness = 0.00015 ft.
Glycerin, sg = 1.26 and μ = 1.49 Pa-s, flows through a 600-mm Ø pipe at 85 liters per second. a. What is the Reynold’s Number? b. What is friction factor? c. What is the critical velocity?
Air flows through a duct at 2,700 cubic feet per minute (CFM). After several feet and a few vents, the air-flow decreases to 1,890 CFM. What is the percent drop that has occurred? (Simplify your answer completely.)
Two reservoirs, which differ in surface elevation by 40 m,are connected by a new commercial steel pipe of diameter8 cm. If the desired flow rate is 200 N/s of water at 20°C,what is the proper length of the pipe?
A pipeline has the following data at its two section A and B Item Section - A Section - B Diameter (cm) 30 45 Elevation (m) 10 16 Pressure (k Pa) 40 30 Kinetic energy correction factor, α 1.08 1.25Assume ahead loss equal to 20 times the velocity head of A and calculate the discharge of water through this pipeline when flowing from B to A.