Q1: Draw the single line diagram of a substation having the following equipments: i) Incoming lines: One, 132kV ii) Outgoing lines: (a) Two 400kV (b) Two, 33kV iii) ,Transformers: (a) One, 150MVA, 132/400KV, D/Y11 (b) One, 20MVA, 132kV/33 D/Y11 One, 2MVA, 33KV/420V,Y/Y iv) Bus-bars: 400 kV-Double bus-bar, 33kV Double bus-bar, 0.42kV single bus-bar Show the positions of necessary equipments that using for protections, measurements and communications.

Q1: Draw the single line diagram of a substation having the following equipments: i) Incoming lines: One, 132kV ii) Outgoing lines: (a) Two 400kV (b) Two, 33kV iii) ,Transformers: (a) One, 150MVA, 132/400KV, D/Y11 (b) One, 20MVA, 132kV/33 D/Y11 One, 2MVA, 33KV/420V,Y/Y iv) Bus-bars: 400 kV-Double bus-bar, 33kV Double bus-bar, 0.42kV single bus-bar Show the positions of necessary equipments that using for protections, measurements and communications.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.41P: Consider the single-line diagram of the power system shown in Figure 3.38. Equipment ratings are...

See similar textbooks

Similar questions

Consider a single-phase electric system shown in Figure 3.33. Transformers are rated as follows: XY15MVA,13.8/138kV, leakage reactance 10 YZ15MVA,138/69kV, leakage reactance 8 With the base in circuit Y chosen as 15MVA,138kV determine the per-unit impedance of the 500 resistive load in circuit Z, referred to circuits Z, Y, and X. Neglecting magnetizing currents, transformer resistances, and line impedances, draw the impedance diagram in per unit.
A Y-connected load bank with a three-phase rating of 500 kVA and 2300 V consists of three identical resistors of 10.58. The load bank has the following applied voltages: Vab=184082.8,Vbc=276041.4, and Vca=2300180V. Determine the symmetrical components of (a) the line-to-line voltages Vab0,Vab1, and Vab2, (b) the line-to-neutral voltages and Van0,Van1, and Van2, (c) and the line currents Ia0,Ia1, and Ia2. (Note that the absence of a neutral connection means that zero-sequence currents are not present.)
Consider the single-line diagram of the power system shown in Figure 3.38. Equipment ratings are Generator 1: 1000MVA,18kV,X=0.2perunit Generator 2: 1000MVA,18kV,X=0.2p.u. Synchronous motor 3: 1500MVA,20kV,X=0.2p.u. Three-phase -Y transformers T1,T2,T3,T4,: 1000MVA,500kV,Y/20kV,X=0.1p.u. Three-phase YY transformer T5: 1500MVA,500kV,Y/20kVY,X=0.1p.u. Neglecting resistance, transformer phase shift, and magnetizing reactance, draw the equivalent reactance diagram. Use a base of 100 MA and 500 kV for the 50-ohm line. Determine the per-unit reactances.
Refer to the 5-bus data given below. Sbase = 400 MVA, the base voltage is 15.0 kV for buses 1 and 3, and 345 kV for buses 2, 4, 5. Note that 1-5 and 3-4 are 15/345 kV transformers.a) Draw a one-line diagram of the power system.b) Find the elements Y23, Y43, Y11 Y33 of the system bus admittance matrix.
1. What are the applications for stripline and microstrip transmission lines? 2. Give 2 examples of characteristic impedance application for each stripline and microstrip transmission lines.
a 12500kva load is supplied at a power facter of 0.8 lagging by a 3 phase transmissiom line whose voltage is to be maintained at 33kv at both ends. Determine the capacity of the synchronous condenser to be installed given that the line resistance and reactance per phase are 5 ohms and 13 ohms respectively
Q4 / Equipment ratings for the four - bus power system shown in Figure are given as follows: TI 73 60 500 Generator GI: 500 MVA, 13.8 KV. X = X2 = 0.20. Xo = 0.10 per unit Generator G2: 750 MVA, 18 KV.X = X2 = 0.18, Xo = 0,09 per unit Generator G3: 1000 MVA, 20 kV, X = 0.17. Xz = 0.20.Xo = 0.09 per unit Transformer Ti: 500 MVA, 13.8 kV A / S00 kV Y. X = 0.12 per unit Transformer T2: 750 MVA, 18 LV A / 500 kV Y, X = 0.10 per unit Transformer T3: 1000 MVA, 20 kV A / 500 kV Y. X = 0.10 per unit each line: X = 50 ohms, X, = 150 ohms 77 The inductor connected to generator G3 neutral has a reactance of 0.028 pu. Draw the zero-, positive-, and negative - sequence reactance diagrams using a 1000 - MVA, 20 - KV base in the zone of generator G3
A 120 MVA, 19.5 kV generator has Xs = 0.15 per unit and is connected to a transmission line by a transformer rated 150 MVA, 230 Y/18Δ kV with X = 0.1 per unit. If the base to be used in the calculation is 100 MVA, 230 kV for the transmission line, find the per unit values to be used for the transformer a. 0.06667 b. 0.1467 c. 0.05 d. 0.0405
Draw the single line diagram of a substation having the following equipments: i) Incoming lines: Two, 132kV ii) Outgoing lines: (a) Five, 132kV (b) Five, 33kV iii) Transformers: (a) One, 25MVA, 132/33kV, D/Y (b) One, 2MVA, 33kV/ 420V,Y/Y iv) Bus-bars: 132 kV-Duplicate bus-bar, 33kV single bus-bar Show the positions of necessary equipments that using for protections, measurements and
An 11 KV, 3-phase transmission line has a resistance of 1.5 Ω and reactance of 4 Ω per phase.Calculate the percentage regulation and efficiency of the line when a total load of 5000 KVA at 0.8 lagging power factor is applied at 11KV at the distant end.
2. A 100 MVA, 18 kV generator, with per unit reactance of X”d= 0.19, X’d = 0.26, and Xd = 1.3 is connected through acircuit breaker to a transformer rated 100 MVA, 240Y/18 kV,X = 0.10 per unit. It is operating at no load and ratedvoltage when a three-phase short circuit occurs at the highvoltage side of the transformer. Find the initialsymmetrical rms current in the line on the low voltageside.
In a 380 kV three-phase transmission system, the diameter of the overhead lines in the form of cylinder conductors is 28 mm. a) How much distance should there be between two conductors using the maximum area calculation equations? Calculate. (Puncture peak strength of air is 30kV / cm.) b) In this configuration, if the distance between phase conductors is 4 m, at what voltage level Calculate the discharge occurs? c) Maximum electric field in the same configuration, for electrode distances to be 8 m Calculate the value. If needed in calculations Ꜫ0 = 8.854x10-12 F / m