Q2/A/ For the three bus power system shown in Fig.(2), all the per unit reactances of its elements are scaled on a common MVA base and they are given as follow : G: 50 MVA, 11 kV, X =0.12p.u. G2: 50 MVA, 11 kV, Xa -0.3 p.u. T: 50 MVA, 11/132kV,X= 0.05 p.u.; T2: 50 MVA, 11/132kV,X=0.08 p.u. Linel: 132kV,X=0.125 pu: Line2: 132 kV, X=0.15 p.u. Line3: 132kV,X=0.25 p.u. For a symmetrical three phase fault occurs at point F find the fault current in amperes? Symmetrical three phase fault NT. T: Rus I Bus 2 Line 1 Line 2 Line 3 Fig.(2) Bus 3

Q2/A/ For the three bus power system shown in Fig.(2), all the per unit reactances of its elements are scaled on a common MVA base and they are given as follow : G: 50 MVA, 11 kV, X =0.12p.u. G2: 50 MVA, 11 kV, Xa -0.3 p.u. T: 50 MVA, 11/132kV,X= 0.05 p.u.; T2: 50 MVA, 11/132kV,X=0.08 p.u. Linel: 132kV,X=0.125 pu: Line2: 132 kV, X=0.15 p.u. Line3: 132kV,X=0.25 p.u. For a symmetrical three phase fault occurs at point F find the fault current in amperes? Symmetrical three phase fault NT. T: Rus I Bus 2 Line 1 Line 2 Line 3 Fig.(2) Bus 3

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.52P

See similar textbooks

Similar questions

Given a 400sq.m single family dwelling unit to be provided with 230V, 1-phase, 2-wire be service, andhaving the following loads: 2-1.5hp A/C, 2-1.0hp A/C, 1-0.5hp water pump, 4-800W water heater, 2-6kWelectric range and 2-1kW microwave oven, determine a) the total connected load, b) the total demand load,c) the overall %demand factor, d) the size of THW feeder conductor, ground wire and IMC conduit, e) therating of feeder overcurrent protection using inverse time circuit breaker
Given a 400sq.m single family dwelling unit to be provided with 230V, 1-phase, 2-wire service, and having the following loads: 2-1.5hp A/C, 2-1.0hp A/C, 1-0.5hp water pump, 4-800W water heater, 2-6kW electric range and 2-1kW microwave oven, determine the total connected load in volt-ampere (VA). Write your answer in numerical format without decimal places.
electrical engg .fig.shows a single-line diagram of a power system where the generator is connected to the bus 1 and the load is connected to the bus 2. The line impedance is 0.12 +j 0.23 pu on a 100 MVA a base. Per unit real power and reactive power supplied to the load are 0.50 and 0.30 respectively. Bus 1 is a slack bus. Use Gauss-Seidel method to determine the (i) voltage at bus 2, (ii) slack bus real and reactive powers, (iii) line flows,
TOPIC: Transmission Lines, Power Systems, and Powerplants:INSTRUCTIONS:- Answer in this format: Given, Illustration, Required Conversion, Solution, Final Answer.- Step-by-step solution, do not skip even simple calculations to avoid confusion.- If answered in written form, make sure it is readable.PROBLEM:The per-phase constants of a 345-kV, three-phase, 150-km-long transmission line are resistance = 0.112/km, inductance-1.1 mH/km, and capacitance = 0.02 uF/km. The line supplies a 180-MW load at 0.9 power factor lagging. Using the nominal-m circuit, determine the sending-end voltage in kV. 351.2 349.3 348.7 350.8
(1) Given a 400sq.m single family dwelling unit to be provided with 230V, 1-phase, 2-wire service, and having the following loads: 2-1.5hp A/C, 2-1.0hp A/C, 1-0.5hp water pump, 4-800W water heater, 2-6kW electric range and 2-1kW microwave oven, determine the total connected load in volt-ampere (VA). (2) Given a 400sq.m single family dwelling unit to be provided with 230V, 1-phase, 2-wire service, and having the following loads: 2-1.5hp A/C, 2-1.0hp A/C, 1-0.5hp water pump, 4-800W water heater, 2-6kW electric range and 2-1kW microwave oven, determine the rating of feeder overcurrent protection in ampere-trip (AT) using inverse time circuit breaker. Write your answer in numerical format without decimal places
Fig. 1 shows the one-line diagram of a 5-bus power system with line impedances and voltage levels in per-unit. The circuit of Fig. 1 has the linear graph shown in Fig. 2, with arrows indicatingdirections assumed for the branches a to h. a) Determine branch-to-node incidence matrix A for the circuit with node 0 as referenceb) Find the circuit Ybus using equation Ybus = ATYpr Ac) A new branch having impedance j0.5 is added between nodes 3 and 4 in the network in Fig. 1. Modify Ybus matrix obtained in part b to account for addition of the new branch.
An electrical motor is supplied from a three-phase ,50 Hz, 410 V system on-board a LNG carrier .When connected in star , it takes a line current of 35 A at a power factor of 0.66 leading. The LNG carrier arrives at port and the motor is subsequently used for powering a container crane It is now connected in delta and is supplied on-shore .Determine for this motor when it takes 64 A at 310 V, from the on-shore supply: 2.1 The power factor of the motor 2.2 the frequency of the supply The motor is returned back to its initial supply and now connected with a new motor in parallel . The new motor is connected in delta and it takes 48.216 kVA at a power factor of 0.77597 lagging with a supply of 50 Hz, 410 V system. Determine for this new arrangement : 2.3 The power factor 2.4 Apparent power taken 2.5 True power taken 2.6 Reactive power taken
he node (busbar) and branch (line) data of a power system are provided in Table Q1.1 and Table Q1.2 respectively. All values in the tables are stated in per unit (p.u.). Using node 1 (busbar 1) as the reference (slack bus), calculate the line flows using the DC power flow method.
A 30 mile, 3-phase transmission line delivers 8,000 kW at 33 kV, p.f. 0.8 lagging. The resistance and reactance of single conductor are 0.6 ohm and 0.72 ohm respectively per mile. Find the percent efficiency of the line.
2) A 3-bus power system is shown below. The three busses are connected through three 340 kV transmission lines of 200km, 150 km, and 150 km long. These transmission lines have the series resistance of 0.05 Ω/km and series reactance of 0.3Ω/km. (a) Find the value of the transmission lines series impedances. (b) Find the bus admittance matrix (Y-bus) of this power system.
The area of an interconnected power system has two units operating on economic dispatch. The variable operating costs of these units are given by C =8P +0.009P2 11 1(R/h) and C = 10P + 0.008P2 where P1 and P2 are in MW. The transmission losses for the area are given by ? = 1.5 × 10−4?2 + 2 × 10−5? ? + 3 × 10−5?2 , MW ?1122 2 2 2 (R/h,) Determine the following when the area λ = 16.00 R/MWh: a. The output of each unit b. Total transmission losses c. Total load demand d. Total operating cost
A 210 km long three-phase transmission line is operated on a 60 Hz network. Line Finally a 40 MVA power with 0.78 back power factor under 120 kV voltage is being shot. The conductor resistance value of the line is 0.10 Ω / km, the inductance value Since 1.30 mH / km and capacitance value is 0.001 µF / km, Medium Transmission Line establishing the equivalent circuit model; a) -Calculate the line current and voltage of the sending side. b) Calculate the power loss on the line. c) Calculate the% voltage regulation value of the line.