Standard addition. Analyte in an unknown gave a signal of 10.0 mV. When 1.00 mL of 0.050 0 M standard was added to 100.0 mL of unknown, the signal increased to 14.0 mV. Find the concentration of the original unknown.

Standard addition. Analyte in an unknown gave a signal of 10.0 mV. When 1.00 mL of 0.050 0 M standard was added to 100.0 mL of unknown, the signal increased to 14.0 mV. Find the concentration of the original unknown.

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter1: Introduction

Section: Chapter Questions

Problem 1.9QAP

See similar textbooks

Related questions

Q: Below is the procedure described for determination of paracetamol according to BP: "Weigh and powder…

A: Interpretation: To identify the correct statement about assay of paracetamol.

Q: Below is the procedure described for determination of paracetamol according to BP: "Weigh and powder…

A: Interpretation: To identify the correct statement about assay of paracetamol.

Q: What cause the spikes in the spectrophotometer reading? Explain

A: In electronic spectroscopy, generally the electron excites from an initial low energy state to a…

Q: A 10.00-g sample containing an analyte was transferred to a 250-mL volumetric flask and diluted to…

A: As per Lambert Beer's Law- Absorbance = Molar absorptivity coefficient * Path length * Concentration…

Q: a 50.00-mL sample containging an analyte gives a signal of 11.5(arbitrary units). A second 50-mL…

A: Solution The mechanism of analyte concentration in field-enhanced sample injection (FESI) is…

Q: Single standard addition method was.16 applied for spectrophotometric analysis of Na+ in a 25 mL…

A: Let us suppose the amount of Na in unknown water sample be x ppm. If we are added the solution 0.500…

Q: Zinc was analysed in acid mine drainage (AMD). The signal obtained from an AAS for the sample was…

Q: A 25.0 ml sample containing Cugave an instrument reading of 23.6 units (corrected for a blank). When…

A: Interpretation: The molar concentration of Cu2+ in the sample is to be determined.

Q: Please answer question 3 and show all work. Thank you

A: Given,Concentration of solution (c) = 0.80 MLength of cuvette (l) = 1.5 cm We need to compare the…

Q: in a standard addition calibration method, 50.0 ml volumetric flasks were used. A 5.0 ml aliquot of…

Q: PART B. Spectrophotometrilc Determination of the Copper Content of a Penny Mass of penny:3.138 Date…

Q: A serum containing sodium Na + gives a signal of 3.09 mV in an atomic emission analysis. Then 4.00…

A: Given that : Initial signal of Na+ = 3.09 mV The volume of added NaCl = 4.00 mL Molarity of the NaCl…

Q: Consider the reaction : A+B 2 AB. A calibration plot was constructed using x as the concentration…

Q: In order to measure riboflavin in a breakfast cereal, a 5.00-gram sample of the cereal was extracted…

Q: concentration

Q: 12. This detector is not used in HPLC: a) ECD b) MS c) Fluorescence d) RI

A: Mixture components are estimated using HPLC detectors. The actual separation in HPLC (High…

Q: Internal standard. Mn was used as an internal standard for measuring Fe by atomic absorption. A…

A: According to beer lamberts law A = Absorbance, K = constant C = concentration

Q: Ex.1. Potassium chromate in the base solution shows the highest absorption at 372 nm, so the…

Q: The molar absorptivities of compounds X and Y were measured with pure samples of each:…

Q: You prepare several dilutions of an unknown compound. You measure the absorbance of each solution at…

A: The graph for concentration-Absorbance is shown below in which slope of the curve is determined.

Q: A solution with a “true” absorbance [A=-log(P0/P)] of 2.10 was placed in a spectrophotometer with a…

Q: 2. Concentration of metal ion. Absorbance of metal ion in solution 0.316 Concentration of metal ion…

A: 2. Given: Initial Volume of Unknown Sample = 20 mL Volume of Final diluted sample = 25 mL…

Q: Please answer question number 4 and show all work explaining how you got the answer. thank you

A: From the calibration curve, the absorbance of 0.35 unit is obtained at 0.45 molar concentration of…

Q: 5. A solution prepared by mixing 10.00 mL of unknown (X) with 5.00 mL of standard (S) containing…

A: Relation between signal ratio and concentration ratio ;AxAs= K Conc. of XConc. of…

Q: At 21 °C, a solution of 12 mL each of 0.00200 M Fe3+ and 0.001000 M SCN- was mixed and brought to…

A: The given reaction is: Fe3+(aq) + SCN-(aq) → Fe(SCN)2+(aq) Here the product, Fe(SCN)2+(aq) is…

Q: Exactly 5.00 mL aliquots of a solution containing analyte X were transferred into 50.00-mL…

Q: Reagent blanks gave the following values: Blank 1 2 3 4 5 6 7 Signal, nA 1.4 2.2 1.7 0.9 0.4 1.5 0.7…

A: (8) Total number of Data = 10 Mean of all the readings will be - Mean = Addition of all…

Q: alpha source was counted for 10 hours at a distance of 2 cm from a detector with an active face area…

Q: HPLC VFA analysis - why do I get so different peaks for very similar samples?

A: Volatile fatty acids are formed during microbial fermentation of organic matter and are present in a…

Q: 1. The instrumental signal from pesticide X in an unknown is 185.6 µA. When 25.0 mL of 0.0325 M…

A: Let the molar concentration of X in the unknown sample be 'a'.

Q: Nitrate is commonly used to determine the reaction of coloured species that are absorbed at 550 nm.…

A: Graph is drawn by using excel.

Q: Below is the procedure described for determination of paracetamol according to BP: "Weigh and powder…

A: Here the question describes the procedure to analyze the paracetamol content in a tablet.…

Q: Mw = 102.1 100 MS-NU-0527 80 40 20 10 20 30 40 50 60 70 80 90 100 Relative Intensity

A: Mass spectrometry is used to determine the unknown compounds from their m/z ratios.

Q: A solution containing Cu2+ is analyzed by atomic absorption and gives an absorbance of 0.01000…

Q: Lithium in a sample is determined by flame emission spectrometry, using a standard additions…

A: If 10 microlitres of 0.010M of lithium nitrate on addition gives 14.6 units, then the sample without…

Q: Absorbance vs. Concentration y = 0.2755x 0 0.200 0.400 0.600 1.000 1.200 1.400 1.600 1.800 2.000…

Q: Part 2: Equilibrium Constant Determination Tube Fe(NO3)3 (mL) HSCN (mL) [Fe³+]; (M) 1 1.00.015 5.0…

A: To calculate FeSCN2+ concentration in M

Q: A 10.00 g sample containing an analyte was transferred to a 250 mL volumetric flask and diluted to…

A: Given, sample is 10 g which is transferred to 250 ml volumetric flask. The first signal after…

Q: Čalculate the concentration of an AMD sample that has an absorbance of 0.155 an the following…

A: Without using the intercept value we can find the concentration at its respective absorbance using…

Q: Consider the following data set: Sample Corrected Absorbance at 470 nm 100 ug/ml CuSO. standard 200…

A: The standard calibration plot is below-

Q: please answer question 2 and show work. thank you

A: Absorption spectrum of 0.80 M M+2 and calibration curve for M+2 are given.While analysing the…

Q: What is the purpose of reference beam in the double-beam spectrophotometer shown in Figure 20-1?…

A: As the name suggests, a double beam spectrophotometer employs two types of beams: reference beam and…

Q: . To determine the concentration of analyte in a sample a standard additions was performed. A…

A: Analyse the data and with given information, sketch the correct graph.

Q: Following the experimental procedure described in the lab manual, a student combined 5.00 mL of…

Q: Analyte in an unknown gave a signal of 9.3 mV. When 100 mL of 0.211 M standard was added to 100.0…

A: Given: The Unknown signal of 9.3 mV When 100 mL of 0.211 M standard was added to 100.0 mL of unknow…

Q: analyte concentration(C)(mg/ml) injection volume (ul) elution time (time) peak DAD signal(mAU)…

A: concentration of mixture= C1V1+C2V2+C3V3+C4V4/(V1+V2+V3+V4)

Q: Formula: ml base x N x meq. wt. x 100 %w/w = Sample weight A 4.59 ml sample of HCI, specific gravity…

A: 50.5ml of 0.9544N NaOH is required. HCl and NaOH reacts in 1:1 ratio. 4.59ml of sample was used…

Q: Standard addition. An unknown sample of Cu2 gave an absorbance of 0.262 in an atomic absorption…

A: Given data contains, Absorbance value of unknown value of Cu2+ is 0.262. Volume of solution is…

Q: A 2.50-mL aliquot of a solution that contains 3.8 ppm iron(III) is treated with an appropriate…

A: Solution - According to the question - The Beer–Lambert law, also known as Beer's law, the…

Q: In using the spectrophotometer PD 303, why is there a need to use water as blank when measuring the…

A: In using the spectrophotometer, water is used as blank when measuring the absorbance of each…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Trending now

This is a popular solution!

Step by step

Solved in 6 steps with 12 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.

Similar questions

Analyte in an unknown gave a signal of 9.3 mV. When 100 mL of 0.211 M standard was added to 100.0 mL of unknown, the signal increased to 16.7 mV. Find the concentration of the original unknown solution.
1. a 50.00-mL sample containging an analyte gives a signal of 11.5(arbitrary units). A second 50-mL aliquot of teh sample, which is spiked with 1.00-mL of a 10.0-ppm standard solution of the analyte, gives a signal or 23.1. what is the concentration of analyte in the original sample?
The ppm concentration of Pb2+ in a blood sample were measured with Spectrophotometry. 5.00 mL of a blood sample were taken and this sample gave a signal of 0.301 a.u.. Another 5.00 mL of a blood sample were mixed with 0.50 mL og 1.75 ppm Pb2+. Then, this mixture was diluted to 25.00 mL and this diluted mixture gave a signal of 0.406 a.u.. What is the ppm concentration of a blood sample?
How do I find Concentration? flask Calculate solution Concentration (M) Volume stock of 0.40 M CuSO4 (ml) Volume of flask (ml) Absorbance at 635 nm(a.u.) 1 2.0 10 .185 2 4.0 10 .362 3 6.0 10 .510 4 8.0 10 .674 5 10.0 10 .843
At 21 °C, a solution of 12 mL each of 0.00200 M Fe3+ and 0.001000 M SCN- was mixed and brought to 25.0 mL with 0.1 M HNO3. The absorbance at 450 nm was measured to be 0.350 (A450 = 0.350). This solution was then heated to 45 °C and the absorbance at 450 nm was measured to be 0.142 (A450= 0.142). Is the reaction: Fe3+(aq) + SCN -(aq) → FeSCN2+(aq) exothermic or endothermic? Explain.
3 to the kit manual 200uL of plasma was mixed with 2.8 ml of the dilution buffer, mixed well then 200 uL of the dilution mixture was pipetted in 0.9 ml of solution A and 0.9 mL of solution B and measured using a spectrophotometer, the concentration was 30. What is the final concentration of the sample after adjusting the dilution factor
Following the experimental procedure, a student combined 5.00 mL of 0.0020 M Fe3+ and 1.00 mL of 0.0020 M SCN- with 4.00 mL of water to create their Trial 1 solution. The student used their spectrophotometer to measure the absorbance of the reaction mixture and recorded an absorbance of 0.095. a. The initial concentration of Fe3+: M (give to nearest 0.0001 M) b. The initial concentration of SCN-: M (give to nearest 0.0001 M) c. The equilibrium concentration of FeSCN2+: (give as decimal to nearest 0.000 001)Hint: The extinction coefficient of FeSCN2+ is 4,630 M-1*cm-1 and the cuvettes we use have a path length of 1.0 cm. d. The equilibrium concentration of Fe3+: M (give as decimal to nearest 0.000 001 M) e. The equilibrium concentration of SCN-: M (give as decimal to nearest 0.000 001 M) f. The equilibrium constant K: (give to nearest tens place)
analyte concentration(C)(mg/ml) injection volume (ul) elution time (time) peak DAD signal(mAU) caffeine 1 1 4.67 302.85 aspartame 5 1 7.53 15.83 benzoic acid 1 1 8.14 89.98 saccharin 1 1 1.91 84.86 mixture(add everything above with 1:1:1:1 ratio) 1 4.47 69.58 How to get the concentration of the mixture in this case?
An unknown sample of Mn2+ gave an absorbance of 0.392 in an atomic absorption analysis. Then 2.00 mL of solution containing 100.0 ppm of Mn2+ (=μg/mL) was mixed with 90.0 mL of unknown, and the mixture was diluted to 100.0 mL in a volumetric flask. The absorbance of the new solution was 0.600. The blank reading for this experiment is 0.010. Denoting the initial, unknown concentration as [Mn2+]i, write an expression for the final concentration, [Mn2+]f, after dilution. Units of the concentration are ppm. In a similar manner, write the final concentration of added standard Mn2+, designated as [S]f. Find [Mn2+]i in the unknown.
From the following data, calculate the concentration of the analyte in the sample read at 700 nm: Absorbance of unknown sample = 0.807 Absorbance of a 130 mg/dl standard = 0.234 Do not answer in image format. Maintain accuracy and quality in your answer. Answer completely.
A spectrophotometer method for the quantitative analysis of Pb2+ in blood uses Cu2+ as an internal standard. A standard containing 1.75 ppb Pb2+ and 2.25 ppb Cu2+ yields a signal of 0.832 for Pb2+ and a signal of 0.351 for Cu2+. A sample of blood is spiked with the same concentration of Cu2+, giving a signal of 0.520 for Pb2+ and 0.289 for Cu2+. Determine the concentration of Pb2+ in the sample of blood.
Suppose that s = 0.28 nA instead of 0.56 nA, but yblank is still 1.26 nA. Find the signal detection limit, the minimum detectable concentration, and the concentration of analyte in a sample with a signal of 7.0 nA.