steel shaft 4 ft long that has a diameter of 5 in is subjected to a torque of 20 kip·ft. Use a standard G = 12 × 106 psi. Set up the equations of stress and twisting angle that is required to solve the problem. 2. Determine the maximum shearing stress and the angle of twist

steel shaft 4 ft long that has a diameter of 5 in is subjected to a torque of 20 kip·ft. Use a standard G = 12 × 106 psi. Set up the equations of stress and twisting angle that is required to solve the problem. 2. Determine the maximum shearing stress and the angle of twist

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.4.5P: A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions...

See similar textbooks

Related questions

Q: A solid shaft in a rolling mill transmits a torque of 1600 N.m. Determine the diameter of the shaft…

A: Given Data T=1600 N.m = 16×105 N.mm Max. Shear stress=40 MPa Angle of twist=8° L=2500 mm G=83 GPa

Q: 318. A solid compound shaft is made of three different materials and is subjected to two applied…

Q: A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is…

Q: A 2-in diameter steel shaft rotates at 240 rpm. If the shearing stress is limited to 12 ksi,…

Q: A solid circular shaft has a uniform diameter of 2" and is 10 ft long. At its midpoint, 65hp is…

Q: A hollow circular shaft with the ratio of internal and external diameters of 0.6 is required to…

Q: 3. A 220-mm-diameter steel shaft have a maximum shearing stress of 12 GPa. Determine the applied…

A: Write the formula for shear stress in the shaft under torsion. τ=16Tπd3 Here, τ is the shear stress…

Q: Determine the torsional shear stress in a solid circular shaft having a diameter of 1.25 in. that is…

Q: 1) A stepped steel shaft consists of a hollow shaft 2.5 m long with an outside diameter of 110 mm…

Q: A hollow steel tube has an outside diameter of 224 mm and inside of 201 mm. Which of the following…

Q: Two steel shafts (G=77.2 GPa) are connected to a coupling disk Band to fixed supports at A and C.…

A: Both the shafts AB and BC are connected in parallel, therefore the angle of twist is the same in…

Q: 3.8 Attaching a hollow shaft to a solid shaft creates the steel shaft. Determine the maximum torque…

Q: A solid steel circular shaft transmits 18 kW of power at 120 rpm. Determine the minimum diameter of…

Q: Problem 3. A solid circular shaft of steel is transmitting 20 kW of power at 120 rpm. Determine the…

Q: a solid shaft in a rolling mill transmits 20 kw at 2r/s. determine the diameter of the shaft if the…

Q: A solid steel shaft will not twist through more than 3 degrees in a 6-m length when subjected to a…

A: Given data: The angle of twist, θ=3°. The length of shaft, L=6 m. The applied torque, T=12 kN·m.…

Q: A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is…

A: Given Data, :-∗Torque,T=1200N⋅m∗Allowable shear stress, ζall=40MPa∗θallowable=∅L=0.75°/m* Shear…

Q: PROBLEM 3. A 5-m steel shaft rotating at 1.20 Hz has 72 kW applied at a gear that is 2 m from the…

A: When an object rotate about the point due to the linear force act on the object is known as the…

Q: A flanged bolt coupling consists of six - ½ inch steel bolts evenly spaced around a bolt circle of…

A: Given data: nst=6nal=4dst=12indal=34inRst=6 inRal=4 inT=200 in.lb Need to determine the stresses in…

Q: circular solid shaft made of vibranium has G=80 Mpa and has a limiting torsional shear stress of 60…

Q: 6. A propeller shaft in a ship is 350 mm in diameter. The allowable working stress in shear is 50…

Q: Torsion Problem 6.0 A solid steel shaft is to transmit 5 hp from the motor to which it is attached.…

Q: Determine the diameter of a solid shaft which will transmit 440 kW at 280 rpm. The angle of twist…

A: Shaft is designed on the basis of following two criteria:- Strength Criteria Induced torsional…

Q: Situation 24: The shaft is made of A992 steel (G = 75 GPa) and has an allowable shear stress of taow…

A: Given data: The shear modulus of steel shaft is G = 75 GPa. The allowable shear stress is τallowabe…

Q: 12 mm PROBLEM 1.25 For the assembly and loading of Prob. 1.9, determine (a) the average shearing…

Q: A steel marine propeller shaft 13 inches in diameter and 15 ft long is used to transmit 9,426 hp at…

A: GIVEN DATA- D=13in L=15ft P=9426hp N=189rpm G=12*10^6 psi WE HAVE TO FIND SHEAR STRESS

Q: 30 mm PROBLEM 3.2 (a) Determine the torque T that causes a maximum shearing stress of 45 MPa in the…

A: Given data:-Maximum shear stress, τmax=45MPaOuter radius, ro=45mm ⇒do=90mmInner radius, ri=30mm…

Q: A turbine developing 15,000 Hp turns the shaft at 300 rpm. The propeller attached to this shaft…

Q: A steel marine propeller shaft 7 inches in diameter and 18 ft long is used to transmit 9,138 hp at…

A: Given data, d= 7 in L= 18 ft = 216 in G= 12*10⁶ psi P= 9138 HP N= 189 rpm

Q: The design of a machine element calls for a 40-mm-outer-diameter shaft to transmit 50 kW. If the…

A: As there are two shaft shown in figure but for figure b , d2 is not given so I have considered…

Q: II. If the permissible shear stress of a solid shaft is of 70 MPa, the torque angle between two…

A: a. Determine the required diameter in the function of the shear stress…

Q: Q5: Determine the diameter of the solid shaft where the angle of twist not exceed 10 and the length…

A: Given: The angle of the twist: →θ=1°=1×π180=0.017 radian Diameter of the shaft=d And length of the…

Q: A solid shaft is to transmits 22 kW at 110 rpm. Determine the diameter of the shaft if the shearing…

A: Given data as per question Power transmitted =22kw Speed =110 rpm hearing stress =35 Mpa The angle…

Q: 1. A solid aluminum shaft 4 m long that has a diameter of 120 mm is subjected to a torque of…

Q: steel shaft 8 ft long that has a diameter of 3 inches is subjected to a torque of 27 kip ft.…

Q: A hollow brass alloy shaft with an outside radius of 50-mm and a wall thickness of 10-mm is…

A: Given data: ro=50 mmt=10 mmT=5.5 kN.m Need to determine the minimum required diameter in mm of a…

Q: 2. A solid shaft is to transmits 22 kW at 110 rpm. Determine the diameter of the shaft if the…

Q: A solid circular shaft has a uniform diameter of 2" and is 10 ft long. At its midpoint, 65hp is…

Q: Determine the maximum torque that can be applied to a hollow circular steel shaft of 100mm outer…

Q: steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is…

A: → Given Data : T = 1200 N.m z = 40 mPa Q = 0.75 / m G = 78 GPaa) For Solid…

Q: A steel marine propeller shaft 14 in. in diameter and 18 ft long is used to transmit 5000 hp at 189…

A: Given data: Unit conversions used are:

Q: Determine the maximum torsion load, in N-m, that a 20 mm diameter aluminum shaft can carry if its…

Q: 3. A machine shaft is supported on bearings 1 m apart is to transmit 190 KW at 300 rpm while…

Q: The torques shown are applied to a 6 mm radius solid shaft with G = 70 GPa. Determine the maximum…

Q: A turbine developing 15,000 Hp turns the shaft at 300 rpm. The propeller attached to this shaft…

A: P=15000Hp N=300rpm

Q: Consider a solid shaft of 18-mm diameter. Determine the maximum shearing stress in the shaft as it…

Q: A steel shaft 3 ft long that has a diameter of 4 in is subjected to a torque of 15 kip-ft. Determine…

A: Given: T = 15 kip-ft D = 4 in

Q: Q. Determine the value of the torque T of the shaft shown in the figure, if the permissible shearing…

A: When the force is applied in tangential direction in the plane of transverse cross-section, torque…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

A steel shaft 4 ft long that has a diameter of 5 in is subjected to a torque of 20 kip·ft. Use a standard G = 12 × 106 psi.

Set up the equations of stress and twisting angle that is required to solve the problem.

2. Determine the maximum shearing stress and the angle of twist

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
Determine the minimum diameter that can be used for a solid circular steel shaft which is limited to an allowable shear stress of 70 MPa and a maximum angle of twist of 1.5o (degrees) per meter length. Applied maximum torque is 25 KN-m and the overall shaft length is 1.25 meters. Shear modulus = G= 80 GPa Note: When using torsion stress formulas, you must convert the angle of twist from degrees to radians.
A solid shaft in a rolling mill transmits 30 hp at 100 rpm. Find the diameter in mm of the shaft so as not to exceed a shearing stress of 42 MPa and an angle of twist of more than 5 degrees in a length of 3 meters. G = 83 GPa
Calculate the maximum and minimum shear stress in a hollow circular shaft of outer diameter 20 mm and thickness 2 mm, subjected to a torque of 92.7 N-m.
An aluminum shaft of two segments is shown below. Determine the allowable torque if the shear stress is not to exceed 30MPa and the angle of twist between the ends of the bar is not exceed 2.3°? (Assume G=80GPa)
A hollow circular shaft with the ratio of internal and external diameters of 0.6 is required to transmit 870 kW at 120 rpm, the maximum torque being 20% greater than the mean. Determine the dimensions of the shaft if the maximum shearing stress and twist in a length of 3m are limited to 60Mpa and 1.4°respectively. The G= 80Gpa.
Problem: 2 A solid shaft is transmitting 9 KW at 550 r.p.m. Determine the diameter of the shaft if the maximum torque transmitted exceeds the mean torque by 20%. Take the maximum allowable shear stress as 78 MPa.