The absorbance of known concentration of a metal complex is obtained by UV-vis spectrophotometer. The results are tabulated: abs 0.27 0.41 0.55 0.69 Calculate the concentration of an unknown sample of the complex that has an absorbance of 0.43 conc 0.2 0.3 0.4 0.5 a. 0.31 b. 0.37 c. 0.33 d. 0.35 e. 0.39

The absorbance of known concentration of a metal complex is obtained by UV-vis spectrophotometer. The results are tabulated: abs 0.27 0.41 0.55 0.69 Calculate the concentration of an unknown sample of the complex that has an absorbance of 0.43 conc 0.2 0.3 0.4 0.5 a. 0.31 b. 0.37 c. 0.33 d. 0.35 e. 0.39

Appl Of Ms Excel In Analytical Chemistry

2nd Edition

ISBN:9781285686691

Author:Crouch

Publisher:Crouch

Chapter12: Spectrochemical Methods

Section: Chapter Questions

Problem 2P

See similar textbooks

Similar questions

A student is working with a metal thiocyanate complex, M(SCN)+, with a molar absorptivity constant, ε, of 6500 cm−1M−1 at 500 nm. If the student is using a 1.00 cm cuvette for absorbance measurements at 500 nm, what concentration of M(SCN)+ will give an absorbance value of 0.120? [M(SCN)+]=
The absorbance of a 0.1 M solution of a complex was 0.15 at max. What is the value of molar absorptivity for this complex? What is the geometry of this complex?
The absorbance values observed during the determination of the complex stoichiometry with the Job method using the spectroscopic method were plotted and the following correct equations were obtained. What is the n value of the compound formed by Fe + 3 and SCN- ions? 1. Line equation: y = 2.6188x + 0.1608 2. Line equation: y = -2.5963x + 2.7203 a) 1 b) 3 c) 0.5 d) 2 e) 5
Palladium (II) and gold (III) can be analyzed simultaneously through reaction with methiomeprazine (C19H24N2S2). The absorption maximum for the Pd complex occurs at 480 nm, while that for the Au complex is at 635 nm. Molar absorptivity data at these wavelengths are Molar Absorptivity, ε 480 nm 635 nm Pd complex 3.55 × 103 5.64 × 102 Au complex 2.96 × 103 1.45 × 104 A 25.0-mL sample was treated with an excess of methiomeprazine and subsequently diluted to 50.0 mL. Calculate the molar concentrations of Pd(II), CPd, and Au(III), CAu, in the sample if the diluted solution had an absorbance of 0.533 at 480 nm and 0.590 at 635 nm when measured in a 1.00-cm cell. explain each step
A FeSCN complex, whose maximum absorbance is at a λ of 580 nm, has a molar extinction coefficient of 5×103 M-1cm-1 . A solution is measured with a 25 mm cell at the same λ , obtaining 20.6% T. Calculate the concentration in [ppm] of the complex in the solution.
You are working with metal thiocyanate complex, M(SCN)+, with a molar absorptivity constant, ε, of 2700 cm−1M−1 at 500 nm. If you are is using a 1.00 cm cuvette for absorbance measurements at 500 nm, what concentration of M(SCN)+ will give an absorbance value of 0.280?
. A student collects the following data for the absorbance of a complex measured in 1.00 cmspectrophotometric cells. The molar absorptivity (ε) of the complex under investigation is 2.25×103L/mol·cm. Calculate the concentration of the complex in solution at each time of the reaction.Time (min)MeasuredAbsorbanceComplex Concentration(M)0.000 1.50010.000 1.31320.000 1.12530.000 0.93840.000 0.750
The absorbance values observed during the determination of the complex stoichiometry with the Job method using the spectroscopic method were plotted and the following correct equations were obtained. What is the n value of the compound formed by Fe + 3 and SCN- ions? 1. Line equation: y = 2.6188x + 0.16082. Line equation: y = -2.5963x + 2.7203
An absorbance versus concentration data for the thiocyanatoiron(III) complex at 510 nm and makes a Beer's law plot.Based on the plot, what [Fe(SCN)2+] would the student report for a solution that has an absorbance of 0.300 at 510 nm? Also select all below closely matches the procedures to be followed in this experiment and why they are being carried out. 1) A Beer's law plot will be used as a means to determine the equilibrium concentration of the thiocyanatoiron(III) complex. 2)A Beer's law plot will be used to confirm known values of the equilibrium constant for the formation of the thiocyanatoiron(III) complex. 3)To make the Beer's law calibration graph, the formation equilibrium for the thiocyanatoiron(III) complex will be flooded with a large excess of thiocyanate ion. 4)To make the Beer's law calibration graph, the formation equilibrium for the thiocyanatoiron(III) complex will be flooded with a large excess of iron(III) ion.
Titanium and vanadium form colored complexes when treated with hydrogen peroxide in 1 M sulfuric acid. The titanium complex has an absorption maximum at 415 nm, and the vanadium complex has an absorption maximum at 455 nm. A 1.00 × 10−3 M solution ofthe titanium complex exhibits absorbance of 0.816 at 415 nm and of 0.485 at 455 nm while a 2.00 × 10−3 M solution of the vanadium complex exhibits absorbances of 0.425 and 0.608 at 415 and 455 nm, respectively. A 1.000-g sample of an alloy containing titanium and vanadium was dissolved, treated with excess hydrogen peroxide, and diluted to a finalvolume of 1000 mL. The absorbance of the solution was 0.697 at 415 nm and 0.533 at 455nm. Calculate: a) The concentration of titanium and vanadium in the sample. b) The percentages of titanium and vanadium in the alloy.
At 580nm, the wavelength of its maximum absorption, a 3.75 x10^-5 M solution of the complex FeSCN2+ has an absorbance of 0.2734 in a 1.00cm cell. what will be the absorbance of a solution in a 2.0 cm cell with concentraion 1.25* 10-5 concentration
Titanium and vanadium form colored complexes when treated with hydrogen peroxide in 1 M sulfuric acid. The titanium complex has an absorption maximum at 415 nm, and the vanadium complex has an absorption maximum at 455 nm. A 1.00 × 10−3 M solution of the titanium complex exhibits an absorbance of 0.816 at 415 nm and of 0.485 at 455 nm, while a 2.00 × 10−3 M solution of the vanadium complex exhibits absorbances of 0.425 and 0.608 at 415 and 455 nm, respectively. A 1.000-g sample of an alloy containing titanium and vanadium was dissolved, treated with excess hydrogen peroxide, and diluted to a final volume of 1000 mL. The absorbance of the solution was 0.697 at 415 nm and 0.533 at 455 nm. Calculate: a) The concentration of titanium and vanadium in the sample. b) The percentages of titanium and vanadium in the