The glass pycnometer is an instrument used for measuring weights and densities of liquids in the laboratory. In the lab-at-home setting, the plastic cup with convex cover was used instead. Given your knowledge of glass and plastics, determine whether the following drying methods are a) acceptable for the glass but not the plastic pycnometer b) acceptable for the plastic but not the glass pycnometer c) acceptable for both pycnometers d) not acceptable for either pycnometer 1) air drying a 2) acetone a 3) heating >

The glass pycnometer is an instrument used for measuring weights and densities of liquids in the laboratory. In the lab-at-home setting, the plastic cup with convex cover was used instead. Given your knowledge of glass and plastics, determine whether the following drying methods are a) acceptable for the glass but not the plastic pycnometer b) acceptable for the plastic but not the glass pycnometer c) acceptable for both pycnometers d) not acceptable for either pycnometer 1) air drying a 2) acetone a 3) heating >

Appl Of Ms Excel In Analytical Chemistry

2nd Edition

ISBN:9781285686691

Author:Crouch

Publisher:Crouch

Chapter14: Chromatography

Section: Chapter Questions

Problem 9P

See similar textbooks

Similar questions

The volume of the solution that can be measured with 5-10 microliter pipette and 2-20 microliter pipette is 0.005-0.01 mL and 0.002 mL-0.02 mL. The volume of the solution that can be measured with 20-200 microliter is 0.02-0.2 mL. The volume 1 mL of solution is measured with 100-100 microliter which has capacity of 0.1 mL to 1 mL. What would the display read for 0.10 mL, 0.20mL, 0.40mL, 0.60 mL, 1.0 mL read when using the micropipettes mentioned above
Taylor was harvesting her beautiful, pure crystals via vacuum filtration from a methanol/water mixedsolvent system. She poured the solution containing her crystals into the Büchner funnel. Then sherinsed her flask with some warm methanol and poured that over the crystals resting in the Büchner…oops! Tell what happened and why
At the diagram of the simple distillation apparatus and label the following parts or general areas: Round bottom flask Condenser (West) Keck clip (add them in) Clamp – and where they should be used 3-way connector vacuum adaptor Heat source Stir bar Thermometer Thermometer adapter Solution to be distilled Distillate Vapors Flow of water Also, where you would increase the number of theoretical plates to separate mixtures with closer boiling points?
The microspectrophotometer employing ___________light provides a rapid and reliable method for identifyingthe generic class of a single fiber
1000 mL of 0.45% NaCl IV for 6.5 hoursDrop factor: 60 gtt/mL Flow rate: ________ gtt/min
Which part of the GC equipment does separation takes place?
If a patient added a 17-g measured dose of polyethylene glycol 3350 (miralax) to 180 mL of water to use as a laxative. If the given volume of the resultant mixture was 195.6 mL. Now, determine the apparent density of polyethylene glycol 3350 and the specific gravity of the mixture.
The recommended patient dose for cisplatin is 20.0 mg/m². For an adult male patient with a body surface area of 1.90 m², determine the correct drip rate to deliver this dose of a 1.00 mg/mL IV solution in 2.50 hours through microdrip tubing with a drop factor of 60.0 gtt/mL. (1 drop = 1 gtt)
1. Minimal OR Maximum 2. Impurities OR substances while Impurities OR substance remain… 3. Centrifuge OR Filter
Jody, a medical assistant in a small clinic, ran out of surface disinfectant while cleaning thecounters in the clinic laboratory. The label of the disinfectant bottle she was using containedinstructions for preparing the surface disinfectant from the concentrated stock solution. Theinstructions read “Dilute the concentrate 1:50 with water.” Jody was using a disinfectant bottlewith a 500 mL capacity. 1. 1. Jody should prepare the replacement surface disinfectant by:a. Adding 1 mL of concentrate to 50 mL of waterb. Adding 10 mL of concentrate to 500 mL of waterc. Adding 10 mL of concentrate to 100 mL of waterd. Adding 10 mL of concentrate to 490 mL of water
(6.65x10^5)/(6.60x10^-6) (3.73x10^8) Please Calaculition. Only typed solution
Diluted skim milk with a protein concentration of 4.3 g/L is to undergoDEF microfiltration. Experiments have been performed using a cellulose-acetate membrane with an average pore diameter of 0.45 µm and AM = 17.3 cm2. For Stage 1 operation at a constant-permeate rate of 15 mL/minute, pressure drop across the cake and membrane increases from 0.3 psi to an upper limit of 20 psi in 400 seconds. The permeate viscosity is 1 cP. If continued in a second stage at constant ∆P at the upper limit until the permeate rate drops to 5 mL/minute, estimate the additional time of operation.Prepare plots of permeate volume in mL and permeate flux in mL/cm2-minute as functions of time.