The question related to Beers low A=-log1oT= log po/p. if the absorbance of the measured =0.75 calculate the power that reached the detector. in case of: A. the dark blank =0.08 b. if the light blank 100%T blank was set 0.80 instead of 100

The question related to Beers low A=-log1oT= log po/p. if the absorbance of the measured =0.75 calculate the power that reached the detector. in case of: A. the dark blank =0.08 b. if the light blank 100%T blank was set 0.80 instead of 100

Macroscale and Microscale Organic Experiments

7th Edition

ISBN:9781305577190

Author:Kenneth L. Williamson, Katherine M. Masters

Publisher:Kenneth L. Williamson, Katherine M. Masters

Chapter14: Ultraviolet Spectroscopy, Refractive Indices, And Qualitative Instrumental Organic Analysis

Section: Chapter Questions

Problem 4Q

See similar textbooks

Related questions

Q: II в D What is the design of figure I1? O diode array spectrophotometer O single beam…

Q: 1. A suggested way to organize your data for Part B of the lab is below. 0.00200 M 0.1 M KSCN…

A: The data table given is,

Q: Copper was determined in a river water sample by atomic absorption spectrometry and the method of…

Q: If the measured absorbance at 280 nm of the protein in a 1.00-cm cuvette = 0.564, what is the…

A: Solution - Beer-Lambert law state The Beer-Lambert law states that there is a linear…

Q: A commercial drink mix is prepared at a concentration of 0.1 M and placed in a spectrophotometer and…

A: The absorbance of the solution is given by the formula

Q: (A) Suppose a solution contains 0.01 M Fe, has a transmittance of 60 % in a 1 cm cell at 625 nm, The…

A: Absorbance = 2 - log(%T) Also, Absorbance = Molar absorbtivity coefficient × Concentration × Path…

Q: A chemist received a report from an analysis involving the iron-phenanthroline method, containing…

A: A question based on absorption that is to be accomplished.

Q: 6. The equation of Beer Lambert's Law is A = Ebc. If the 'b' is distance, 'E' is absorptivity, and…

A: In Beers - Lambert's equation what does 'c' represent ?

Q: A 4.75 mg/L Co (FM = 58.93) solution has a percent transmittance of 19.2 % in a 1.00 cm cell at 635…

Q: For an ASTM grain size of 9, approximately how many grains would there be per square inch (a) at a…

A: Average number of grains per square inch:

Q: fill in the column thats empty by finding the standard deviation for each average absorbance, with…

A: Concentration of Dye Average Absorbance of replicate Standard division 1mg/L 0.269 0.731…

Q: Table II Cuvette # Concentration Absorbance 0.50 M 1 1.049 2 0.40 M 0.926 3 0.20 M 0.740 0.298 4…

A: The formula for Beer-Lambart law is given by

Q: What is the concentration of a solution with an absorbance at 600 nm (A600) of 0.8 that has an…

A: absorbance is commonly known as optical density, which explains that amount of light absorbed by…

Q: Nitrite ion, NO2-, is a preservative for bacon and other foods, but it is potentially carcinogenic.…

A: a) The absorbance due to the coloured product from nitrite added to sample C is, 0.967 - 0.622 =…

Q: A toluene solution (1.50 mg / L) shows an absorbance of 0.30 in a cuvette with a 0.025 mm optical…

A: The given data contains, Absorbance of toluene = 0.30 Pathlength of cuvette = 0.025 mm.…

Q: A 0.035 g of KMnO4 was dissolved in 200 mL of distilled water. This solution had a transmittance of…

Q: An acidic solution of bromothymol blue has a max absorbance of 615nm. A 5.0 g/L of this solution was…

A: Solution: From the Beer- Lambert's law, we have A = ebc. e: malar absorbivity, b : cuvette path…

Q: For part 2 of the procedure 5 different volumes were prepared of 0.0040 M KMnO4. Table 2- Data for…

Q: 7. Fill the absorbance value below; Path length % T 0.2 0.4 0.6 0.8 1.0 25 12.5 6.25 3.125 100 50…

A: The objective of the question is to fill the table with the correct absorbance values for the given…

Q: Consider that a single sample was analyzed using two different spectrometric instruments. One has…

A: A sample was analyzed with the help of two different spectroscopic instruments. In first…

Q: A beverage drink mix sample is prepared by mixing a packet of beverage powder in a gallon (3.78 L)…

Q: Tablet powder containing 100mg of promazine hydrochloride is ground to a paste with 10 ml of 2 M…

A: given data are- – Absorbance reading=0.855 is read at a wavelength wavelength of 251 nm – a (1%, 1…

Q: Based on the picture i) Calculate the limit of detection (LOD) and limit of quantitation (LOQ) for…

A: # (i): Given standard deviation, s = 0.0050 Slope of the calibration curve, m = 0.0693 Detection…

Q: A chemist received a report from an analysis involving the iron-phenanthroline method, containing…

A: Solutions Hence option (d) is correct answer 37.93ppm

Q: What is the concentration of a sample that transmits 70% signal at a certain wavelength upon…

Q: A 4.48 mg sample of a compound has a molar mass of 158.03 g/mol was dissolved in a 1000 mL…

A: Mass of compound, wB = 4.48 mg Molar mass, MB = 158.03 g/mol Volume of solution, V = 1000 mL…

Q: The measured absorbance of a solution with a pathlength of 1.00 cm is 0.544. If the concentration is…

A: pathlength (l) =1.00 cm Absorbance (A) = 0.544 concentration(c) = 1.40 x 10 —3M

Q: A solution containing Cu2+ is analyzed by atomic absorption and gives an absorbance of 0.01000…

Q: Suppose that you follow the procedure and find the absorbance of the final solution to be 0.475.…

A: Given: The calibration curve equation is, => y = 0.1216 x + 0.0189 Where y = absorbance And x =…

Q: Sample and Treatment Li (ug/mL) Calibration Method Flame Type 1. None 25.1 standard curve air/CH2 2.…

Q: In spectophotometry, what should be done if there is a greater absorbance reading than the most…

A: The concentration is directly proportional to the absorbance value. That means, the higher the…

Q: Lithium in a sample is determined by flame emission spectrometry, using a standard additions…

A: If 10 microlitres of 0.010M of lithium nitrate on addition gives 14.6 units, then the sample without…

Q: The transmittance of a solution measured at 590 nm in a 1.5-cm cuvette was 76.2%. (a) What is the…

A: We have to predict the absorbance, absorptivity and the concentration.

Q: Which of the following is not true for magnetic sector mass spectrometer? Select one a. lons gain…

A: The mass spectrometer is used to detect the fragmented mass of a molecule which can give the idea to…

Q: A 10 μL aqueous sample containing 1 attogram of Rb+ was injected into a graphite furnace atomic…

A: Given : Volume of solution = 10 μL = 0.01 mL (since 1 mL = 1000 μL )…

Q: The drug Librium gives a polagraphic wave with E1/2 = -0.265 V (vs SCE) in 0.05 M H;SO4. A 50.0 mL…

Q: When using cuvettes to measure the absorbance of a solution, why is it necessary to only hold the…

A: Generally during the measurement of absorbance of a solution ,we hold the cuvettes near the top ,due…

Q: A solution in part B initially contains (4.0800x10^-4) molar SCN" and (2.850x10^-3) molar Fe3+ This…

A: Given that: absorbance = 4.810×10-1 initial concentration of Fe3+ = 4.0800×10-4 M initial…

Q: The spectrophotometer is set at 600 nm. The absorbance of each cuvette is read. The data is shown…

Q: 1) Determine the total volume of the standards by using a formula in the appropriate boxes (your…

A: The data is given for absorbance versus concentration of different solutions.

Q: An ethanol solution of 3.5 mg/100 ml of compound Y (150.0 g/mol) in a 1.00 cm quartz cell has an…

Q: Find the concentration of benzene in hexane if the absorbance is 0.188 in a 1.000-cm cell.

A: Given data : Absorbance(A) = 0.188 Path length (b) = 1 cm Molar absorbance(ε) of benzene is 210…

Q: A chemist received a report from an analysis involving the iron-phenanthroline method, containing…

A: A question based on tools in analytical chemistry that is to be accomplished.

Q: THE EXPERIMENTAL WRITE-UP AND COMPLETE THE PRE-LAB PRIOR TO DOW umber is: 620 n intensity of 4.06 n…

A: According to the question, we have a Quinine calibration curve and we neee to determine the.…

Q: Blue Blue dye stock solution 0.293 M Absorbance at 630 nm 0.00265 Calibration curve y = 0.0833x A…

A: a) The stock solution of blue dye has concentration = 0.293 M Since the volume of blue dye taken =…

Q: Quinine in a 1.553-g antimalarial tablet was dissolved in sufficient 0.10 M HCl to give 250 mL of…

A: From the Beer Lamberts Law it is clear that absorbance and concentration are directly proportional.…

Q: While performing absorbance measurements of standard solutions, Taranpreet used - 8 ml of solution…

Q: Barium sulfate from a 1.300-g sample was contaminated with 9.4 mg of Fe2(SO4)3 and weighed a total…

A: Solution We know that A) Hence, the apparent % BaSO4 is 24.153%. B) Hence,…

Q: An unknown sample of Cu2* gave an absorbance of 0.262 in an atomic absorption analysis. Then 1.00 mL…

Question

The question related to Beers low A=-log1oT= log po/p. if the absorbance of the measured =0.75 calculate the power that reached the detector. in case of:

A. the dark blank =0.08

b. if the light blank 100%T blank was set 0.80 instead of 100

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Quality Assurance and Calibration Methods

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.

Similar questions

0.1120 g of a solid sample containing copper was dissolved by acid and transferred to a 250.00 mL volumetric flask and volume was made up with distilled water. The solution was then diluted by a factor of 25. The final solution was analyzed by atomic absorption spectrophotometry and the concentration was found be 2.982 ppm, What is the weight percentage of copper in the original solid sample? Keep four significant figures in your final answer.
An unknown sample of Cu2+ gave an absorbance of 0.475 in an atomic absorption analysis. Then 5.00 mL of solution containing 75.0 ppm (= µg/mL) Cu2+ was mixed with 45.0 mL of unknown, and the mixture was diluted to 500.0 mL in a volumetric flask. a) Write an expression for the final concentration after dilution. b) Calculate the final concentration of the added standard. c) The absorbance of the new solution was 0.987. Find the initial concentration of Cu2+ in the unknown sample
Calculate the specific absorbance ratio (SAR), where A620 = 0.285 and A280 = 0.795. Enter your result with 3 decimal places.
A set of three replicate AAS measurements were made from the same calcium standard. Use the information below to determine the LOD for calcium analysis. ⚫ The standard was prepared by dissolving 0.020 g of CaCO, in acid and diluting to 1.000 L. ⚫ After blanking the instrument, the three absorbance readings from the standard were 0.101, 0.096, and 0.104. Hint: Determine the slope of a 'two-point' calibration plot using the blank and average reading of the standard; use the standard deviation of the 3 absorbance readings as s ( )4 ppm ( )3 ppm ( ) 1 ppm ( ) 0.2 ppm
For the determination of Fe3 +, 25 mL of sample taken from sea water is diluted to 100 mL and a quantity of the obtained solution is taken and Fe3 + is determined by atomic absorption spectrophotometer. The absorbance values of the standard and sample solutions are below, and calculate the Fe3 + concentration in sea water in mg / L by drawing the relevant graph.Solution Absorbance1 mg / L Fe3 + 0.04095 mg / L Fe3 + 0.205110 mg / L Fe3 + 0.411615 mg / L Fe3 + 0.620820 mg / L Fe3 + 0.8222Sample Solution 0.5155
1. An unknown sample of Cu2+ gave an absorbance of 0.262 in an atomic absorption analysis. Then 1.00 mL of solution containing 100.0 ppm Cu2+ was mixed with 95.0 mL of unknown, and the mixture was diluted to 100.0 mL in a volumetric flask. The absorbance of the new solution was 0.500. a) Denoting the initial unknown concentration as [Cu2+]i, write an expression for the final concentration [Cu2+]f, after dilution. Units of concentration are ppm. b) In a similar manner, write the final concentration of added standard Cu2+ designated as [S]f. c.) Find the [Cu2+]I in the unknown
An unknown sample of Mn2+ gave an absorbance of 0.392 in an atomic absorption analysis. Then 2.00 mL of solution containing 100.0 ppm of Mn2+ (=μg/mL) was mixed with 90.0 mL of unknown, and the mixture was diluted to 100.0 mL in a volumetric flask. The absorbance of the new solution was 0.600. The blank reading for this experiment is 0.010. Denoting the initial, unknown concentration as [Mn2+]i, write an expression for the final concentration, [Mn2+]f, after dilution. Units of the concentration are ppm. In a similar manner, write the final concentration of added standard Mn2+, designated as [S]f. Find [Mn2+]i in the unknown.
A 131.7 mg sample of powdered Carbamazepine tablets was boiled with ethanol, filtered and then made up to 100 mL with ethanol. 5 mL of this solution was then diluted to 250 mL with ethanol and the absorbance at 285 nm found to be 0.486 in a 1cm path length cell.Calculate the content (% m/m) of Carbamazepine in the powder, taking A(1%, 1 cm) as 490.(State your answer to 1 decimal place and include the units)
For an ASTM grain size of 9, approximately how many grains would there be per square inch (a) at a magnification of 100? (b) without any magnification?
A chemist received a report from an analysis involving the iron-phenanthroline method, containing the calibration curve for Fe standards (20 ppm, 30 ppm, 40 ppm, 50 ppm, and 60 ppm) and their corrected absorbances. The report stated that the equation of the line and r2 were as follows: y = 0.015066 x – 0.154424 r2 = 0.9997 The sample they tested gave a corrected reading of 0.417. How much Fe is present in ppm? 2.80 17.43 2.60 37.93
Maria was tasked to determine the concentration of a Fe2(SO4)3 solution. She prepared 5 different standards of Fe2(SO4)3 using the table below as her guide. She ran the standards and the unknown solution through UV-VIS spectroscopy and recorded the absorbances of each solution. HINT: use the dilution equation to determine the concentration of Fe2(SO4)3 in each test tube before preparing the standard curve. NOTE: No need to force the line to pass through zero. Just graph the data as is. What is the slope of the line of the standard curve from the given data? What is the concentration of the unknown solution?
1. What is the concentration of the dye in a solution with a percent transmittance reading of 61.6% at 570 nm? 1a. If the solution in Part 1 was made by taking 10.00 mL of a stock solution and diluting it to 100.00 mL, what is the concentration of the dye in the stock solution?