The rod BD is made of material with G1= 124 GPa has a diameter 34 mm is bonded to the tube CA at point B, the tube made of material with G2=211 GPa has an outer diameter 73 mm and wall thickness of 10 mm. If T1=579 N.m and T2-1042 N.m, answer the following questions: A T2 N-m 0.4 m 0.1 m 0.3 m T1 N-m The polar moment of inertia of the rod BD is The polar moment of inertia of the tube CA is The maximum shear stress of the rod BD is

The rod BD is made of material with G1= 124 GPa has a diameter 34 mm is bonded to the tube CA at point B, the tube made of material with G2=211 GPa has an outer diameter 73 mm and wall thickness of 10 mm. If T1=579 N.m and T2-1042 N.m, answer the following questions: A T2 N-m 0.4 m 0.1 m 0.3 m T1 N-m The polar moment of inertia of the rod BD is The polar moment of inertia of the tube CA is The maximum shear stress of the rod BD is

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two rods are connected to each other and are restrained at top and bottom. The top portion is steel with modulus of elasticity equal to 200x10^3 MPa and coefficient of thermal expansion equal to 11.7x10^-6/C, the bottom is made up of brass with modulus of elasticity equal to 105x10^3 MPa coefficient of thermal expansion equal to 20.9x10^-6/"C. The temperaturé rose to 50°C from normal condition introducing stresses in the bar. Determine the force induced in the bar. Note: Final Answer in 4 decimal places.
The rod BD is made of material with G1= 124 GPa has a diameter 34 mm is bonded to the tube CA at point B, the tube made of material with G2=211 GPa has an outer diameter 73 mm and wall thickness of 10 mm. If T1=579 N.m and T2=1042 N.m, answer the following questions: The maximum shear stress of the rod BD is The maximum shear stress of the tube CA is The maximum shear stress of the assembly is The angle of twist between D and B is The angle of twist between C and A is The angle of twist at D is Your answer The angle of twist between C and B is Your answer The reaction at point A is
The rectangular bar is connected to the support bracket with a 11-mm-diameter pin. The bar width is w = 60 mm and the bar thickness is 10 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 120 MPa, the bearing stress in the bar cannot exceed 120 MPa, and the bearing stress in the bracket cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported by the structure.
The circular section steel bar bent in L shape is attached to a fixed wall at end A. A force P is applied to the rod in the vertical direction from the free end C. In what range is the safe diameter value of this ductile rod according to Von-Mises criterion? P=3kN, L1=3m, L2=2m, sak= 400MPa, tak= 200MPa, safety factor : n = 2 p = 3
A steel [E = 200 GPa] rod with a circular cross section is 13-m long. Determine the minimum diameter D required if the rod must transmit a tensile force of 23 kN without stretching more than 4 mm. 13.18 mm 28.25 mm 20.13 mm 25.90 mm 21.81 mm
The tube is made of copper and has an outer diameter of 35 mm and a wall thickness of 7 mm. Determine the eccentric load P that it can support without failure.The tube is pin supported at its ends. Ecu = 120 GPa, sY = 750 MPa.
A bar made of A-36 steel has the dimensions shown below. If an axial force of P = 65 kN is applied to the bar. Use E = 200 GPa for A-36 steel. Determine the change in its length: ______ µm.
Question 1: [Strain Energy Due to Direct Stresses] A steel bar of a length, diameter and Young’s modulus of 400 mm, 20 mm and 200 GPa is placed concentrically within a brass tube which has an outside diameter,thickness, length and Young’s modulus of 30 mm, 4 mm, 400 mm long and 100 GPa respectively. The compound bar hangs vertically with its upper end rigidly fixed with a collar fitted to the bottom end. The application of a load P results in the compound bar storing a total of 7 Jof energy. Calculate:1The gradually applied load2The suddenly applied load3The impact load that falls 150 mm and induces 7 J of energy4The instantaneous stresses in both materials5The instantaneous elongation of the compound rod
Why is is that when I compute for the diameter, the answer is 7.9706? How was 13.22 obtained? Bartleby link for solution: https://www.bartleby.com/questions-and-answers/a-steel-rod-is-stretched-between-two-rigid-walls-and-carries-a-tensile-load-of-5000-n-at-20c.-if-the/5c99ed3b-d083-41be-a905-b15aa3bc8648
The pipe assembly shown is subjected to a force F = 7 kN and P = 14 kN. It is made of steel with Sy = 250 MPa. Determine the safety factor at point H using the maximum shear stress theory. Select one: a. NH = 6.427 b. NH = 3.570 c. NH = 5.355 d. NH = 4.590
1) A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm, and it's length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa and the circumferential stress is limited to 60 MPa 2) A compound thin cylinder has a common diameter of 100 mm, and the inner cylinder has a thickness of 2,5 mm. The radial pressure between the two cylinders is 200 KPa and the difference between the two common diameters before shrinkage was 0,004305 mm. E=200 GPa Determine : A) Thickness of the outer cylinder B) Resultant hoop stresses in both cylinders if the compound cylinder is subjected to an internal pressure of 180 KPa
A unique column has been created with the geometry shown below, where the radius is r = (0.6e-0.08y2) m, the variable y is in meters. The column density of the column material is ρ = 3.21 Mg/m3. Determine the average normal stress at the bottom of the column (y = 0) in units of Pa.