Water at 20°C flows through a 6 cm diameter pipe which has a 180° vertical bend, as in Fig. The total length of pipe between flanges 1 and 2 is 75 cm. When the mass flow rate is 31.89 kg /s, Gauge pressure at p1 = 76 kPa, and p2 = 47 kPa. Neglecting pipe weight, determine the X component ( Shown on figure ) of the force to the nearest N which the flanges must withstand for this flow.

Water at 20°C flows through a 6 cm diameter pipe which has a 180° vertical bend, as in Fig. The total length of pipe between flanges 1 and 2 is 75 cm. When the mass flow rate is 31.89 kg /s, Gauge pressure at p1 = 76 kPa, and p2 = 47 kPa. Neglecting pipe weight, determine the X component ( Shown on figure ) of the force to the nearest N which the flanges must withstand for this flow.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

pls replyy Gasoline (SG-0.7) flows down an inclined pipe whose upper and lower sections are 90 mm (section 1) and 60 mm (section 2) in diameter respectively. The pressure and velocity in section 1 are 280 kPa and 2.3 m/s respectively. If the difference in elevation between the 2 sections is 2.5m, find the pressure at point 2.
Water at 20 ° C flows through a 5-cm-diameter pipe that hasa 180 °vertical bend, as in Fig. P3.43. The total length ofthe pipe between flanges 1 and 2 is 75 cm. When the weightflow rate is 230 N/s, p 1 = 165 kPa, and p 2 = 134 kPa.Neglecting pipe weight, determine the total force that thefl anges must withstand for this flow.
A pump is discharging 12 liters/sec of water through 10 cm diameter pipe. When the pressure on the discharge side of the pump is 700 kPa, what pressure can be expected in the discharge pipe at a point 540 m distant from the pump and 45 m higher in elevation. Use n = 0.015.
In a horizontal pipe water flows at a rate of 9.1 L/s. Here, the pipe has two sections, one with a diameter of 10.16 cm and the other with a diameter of 5.08 cm, with a gradual smooth reducing section. In this case, a mercury manometer is used to measure the pressure difference. If friction is negligible how would I find the differential height of mercury between the two sections? If the manometer on the 5.08cm pipe section was replaced with a pitot tube how would the reading change? any help would be deeply appreciated
A jet of water, issuing from sharp-edged vertical orifice under a constant head of 60 cm , has the horizontal and vertical coordinates measured from vena contracta at a certain point as 10. cm and 0.45 cm respevtively. Find Cc if Cd= 0.60.include your free body diagrama.0.612 b.0.962 c.0.98 d.0.623
A 30° elbow is used to deflect water flow at a rate of 14 kg/s in a horizontal pipe upward The elbow discharges water into the atmosphere Cross-sectional areas of the elbow are 113 cm^2 at the inlet and 7 cm^2 at the outlet. The elevation difference between the centers of the outlet and the inlet is 30 cm Neglect the weight of the elbow and the water inside the elbow,Using appropriate integral equations, find a) Wet and outset velocity b) Gage pressure at the center of the inlet section of the elbow c) Anchoring force required to hold the elbow In place Take the density of water to be 1000kg/m^3 & the flow is incompressible.
Airstream flows in a converging duct from a cross-sectional area A1=50cm2to across-sectional area A2=40cm2. If T1=300K, P1=100kPa, and V1=100m/s, find area throat, velocity in throat and temperature in throat.
Consider the incompressible flow of water through a divergent duct, where the inlet has a velocity & section area of 5 ft/s & 10 ft2. If the exit area is 5x the inlet area and the density of water is 62.4 lbm/ft3, solve for the pressure difference. (Please type answer no write by hend)
When a jet of water gushing from a short pipe with a diameter of D= 5 cm, located at a depth of h= 6.6 m from the surface of a fixed level reservoir shown in the figure, hits a horizontal plate that makes an angle of 30o with the jet axis (friction effects are neglected), a)Determine the scalar value and direction of the impact force exerted by the water on the plate (Enter the numerical value of the direction you think is correct in the direction-number image in Figure 3 in the box named "Direction-effect". For example: '1' will be entered for the upward direction). b)Determine the scalar value of the reaction force of the plate and determine its direction (Enter the numerical value of the direction you think is correct in the direction-number image given in Figure 3 in the box named "Direction-reaction". For example: '1' will be entered for the upward direction).
Water flows from a pressurized tank (in figure below), through a 10.0 cm diameter pipe, exits from a 5.0 cm diameter nozzle, and rises 5.0 m above the nozzle. Determine the pressure in the tank if the flow is steady, frictionless, and incompressible.
A 90" elbow is used to direct water flow at a rate of 0,025 m3/s in a horizontal pipe upward. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference betwoen the centers of the exit and the inlet of the elbow is 35 cm. The weight of the elbow and the water in it is considered to be negligible. Determine the anchoring force needed to hold the elbow in place A) 27 N 3433.5 N C) 79.5 N D) 132. 9 E) 106. 5 N
Water moves through a constricted pipe in steady,ideal flow. At the lower point shown in the figure, thepressure is P1 = 1.75x104Pa and the pipe diameter is6.00 cm. At another point y = 0.250 m higher, thepressure is P2 = 1.20 x 104Pa and the pipe diameter is3.00 cm. Find the speed of flow (a) in the lower sectionand (b) in the upper section.(c) Find the volume flow rate through the pipe.Ans. ( (a) 0.638 m/s (b) 2.55 m/s (c) 1.80 x 10-3 m3/s ).