The three parallel loads in the circuit shown in Fig. 3 absorbing an average power of 24 kW and 18 KVAR of magnetizing vars; load 2 is absorbing an average power of 48 kW and generating 30 KVAR of mag- netizing reactive power; load 3 consists of a 60 n resistor in parallel with an inductive reactance of 480 N. Find the rms magnitude and the phase angle of V, if V, = 2400 0° V(rms). can be described as follows: Load 1 is %3D

The three parallel loads in the circuit shown in Fig. 3 absorbing an average power of 24 kW and 18 KVAR of magnetizing vars; load 2 is absorbing an average power of 48 kW and generating 30 KVAR of mag- netizing reactive power; load 3 consists of a 60 n resistor in parallel with an inductive reactance of 480 N. Find the rms magnitude and the phase angle of V, if V, = 2400 0° V(rms). can be described as follows: Load 1 is %3D

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.12P: The voltage v(t)=359.3cos(t)volts is applied to a load consisting of a 10 resistor in parallel with...

See similar textbooks

Similar questions

Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
Under balanced operating conditions, consider the 3-phase complex power delivered by the 3-phase source to the 3-phase load. Match the following expressions, those on the left to those on the right. 0) Real power, Py (ii) Reactive power, Qu (ii) Total apparent power Sy (iv) Complex power, Sy (a) (V3 VLL. IL)VA (b) (V3 Vu sng) var (e) (V3 VLL. IL cos ø) W (d) Py +Qy Note that VLL is the rms line-to-line voltage, IL is the ms line current, and o is the power-factor angle.
1. a) Find the rms magnitude and the phase angle of ICA in the circuit shown. 2. b) What percent of the average power delivered by the three-phase source is dissipated in the three-phase load?
The sending-end voltage in the circuit seen is adjusted so that the load voltage is always 13,800 V(rms). The variable capacitor is adjusted until the average power dissipated in the line resistance is minimum. 1. a) If the frequency of the sinusoidal source is 60 Hz, what is thevalue of the capacitance in microfarads?2. b) If the capacitor is removed from the circuit, what percentageincrease in the magnitude of Vs is necessary to maintain 13,800V(rms) at the load?3. c) If the capacitor is removed from the circuit, what is thepercentage increase in line loss?
In the circuit shown in the figure, there is a load between the terminals a and b, consisting of the series connection of the resistor R0 and the inductance L0. The amplitude of the voltage Vs (t) is two root hundred and fifty phase angle Qs = zero degree period T = 200 PI microseconds. Since R = 300 ohms C = 1 nano F. a) Find the values of R0 and L0 that enable the load to draw maximum average power from the circuit b) Calculate the complex power on the load.
Suppose the circuit shown represents a residential distribution circuit in which the impedances of the service conductors are negligible and Vg1=Vg2=120 0° V (rms). The three loads in the circuit are L1 (a new refrigerator, a coffee maker, and a microwave oven); L2 (2 incandescent lamps, a humidifier, and a ceiling fan); and L3 (a clothes washer and a clothes dryer). Assume that all of these appliances are in operation at the same time. The service conductors are protected with 20 A circuit breakers. Will the service to this residence beinterrupted? Why or why not?
The two loads shown can be described as follows: Load 1 absorbs an average power of 60 kW and delivers 70 kVAR of reactive power; Load 2 has an impedance of (24+j7) Ω. The voltage at the terminals of the loads is 25002 cos 120π t V.1. a) Find the rms value of the source voltage.2. b) By how many microseconds is the load voltage out of phase withthe source voltage?3. c) Does the load voltage lead or lag the source voltage?
A Y-connected balanced three-phase source is feeding a balanced three-phase load. The voltage and current of the source coil are: Calculate the following: The rms phase voltage. The rms line-to-line voltage. The rms current in the source. The rms current in the transmission line. The frequency of the supply. The power factor at the source side, state leading or lagging. The three-phase real power delivered to the load. The three-phase reactive power delivered to the load. If the load is connected in delta configuration, calculate the load impedance.
Between the terminals a and b in the figure, there is a load formed by connecting the resistor R0 and inductance L0 in series. The amplitude of the voltage Vs (t) is √2 150 volt phase angle Qs = 0 degree period T = 200π microseconds. Since R = 300ohm and C = 1 microfarad A) If the load phase angle QL = 30 degrees, find the values of R0 and L0 that enable the load to draw the maximum average power from the circuit. =? B) Calculate the average power on the load. =?
An investor own two large stores at Dubai. Both malls are connected in parallel and operating at an unknown voltage. The local utility system voltage is 13.8 kVrms and supplied power to the malls through a feeder line with impedance equal to 1+j2.5 ohms. Store 1 is consuming 400 kW at 0.8 pf lagging while Store 2 is consuming 300 kVAR at 0.75 pf lagging. Determine the following: a) The stores' operating rms voltages. b) The total real and reactive power of the ehole system. c) The overall pf of the whole system.
In the given circuit, the amplitude of the input voltage is 180 Volts RMS and its phase is 45 degrees.The power values that the loads receive/give are given below.What is the phase of the current phasor I0?Load 1 = 1.8 kW and capacitive 1.2 kVAR8 kW with load 2 = 0.5 back power factorLoad 3 = 3 kVA with 0.9 forward power factor
The circuit with 3 parallel loads is described as follows. The load draws an average power of 1.8 kW (absorbing) and is behindlagging power factor 0.8. The load 2 draws 20 kVA and the leading power factor is 0.6. If the load is 3;3 Z j is an impedance of '2.5 5.0'. If the source frequency is 60 Hz, derive the steady-state equation for () V t s.