The torsion shafts shown below are made of the same material. Which shaft will have the bigherrotation under lead? Which shaft will have the higher stress under load?Select oneCa Element 2 has higher stress and largerotation2.O b. Element 1 has les stress and largerrotatione Element I lhas higlier atre and larger rotationDd. Hoth elements ltve tlie stres atud sotation

Stress τ=T×16πd3 Stress is inversely proportional to the diameter. Therefore the smaller…

The torsion shafts shown below are made of the same material. Which shaft will have the bigher rotation under load? Which shaft will have the higher stress under load? Select one a Element 2 has higher stress and larger rotation 2. O b. Element 1 has les stress and larger rotation Element I has higlier atres and larger rotation d. Hoth clements lave thie stres atud votation

The torsion shafts shown below are made of the same material. Which shaft will have the bigher rotation under load? Which shaft will have the higher stress under load? Select one a Element 2 has higher stress and larger rotation 2. O b. Element 1 has les stress and larger rotation Element I has higlier atres and larger rotation d. Hoth clements lave thie stres atud votation

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A shaft in torsion only is to transmit 2500 hp at 570 rpm. Its material’s allowable shear stress is 10 ksi. (a) What should be the diameter of a solid shaft? (b) If the shaft is hollow, Do = 2Di, what size is required? (c) Which is the lighter? By what percentage? (d) Which shaft is the more rigid? PLEASE I NEED IT ASAP . THANK YOU
Design the size of solid steel shaft to be used for a 500 hp, 250rpm application if the allowable torsional deflection is 1o andthe allowable stress is 10,000 psi and modulus of rigidity is 13x 106 psi. Round your answer to the nearest 1/8 inch.
The maximum torsional shear stress of a shaft with diameter D can be found at what distance from the center of the shaft?
Bearing stress 2. Please provide proper discussion and illustration also complete solution and clear solution please thank you. Determine the length of a square key to be used for a 3.73 kW 1800 rpm electric motor. Motor shaft diameter is 35 mm and the height of the key is approximately one-half of the shaft size. The bearing stress on the key is?
Given: angle α=64o. Cross sections of both rods are square with sizes a1=21mm, a2=13mm. The rods are made of steel with yielding stress σY=270MPa; factor of safety n=2,2. Find: allowable value of force (in kN) from strength calculation FA = ?
SS 304 steel shaft is 3 m long and has an outer diameter of60 mm. When it is rotating at 60 rad/s, it transmits 30 kWof power from the engine to the generator. Determine thefollowing: a. The smallest thickness of the shaft if the allowableshear stress is 150 MPa and the shaft is restricted notto twist more than 0.08 rad. Use G for steel = 83 GPa. b. The percentage savings in weight had the generatorutilized a solid shaft. Assume same material, length andtorque capacity.
Question twoa) Shafts and tubes having circular cross sections cannot be used to transmit powerdeveloped by a machine. True or False? b) Explain the concept of torsion. c) If the applied torque on shaft CD is T = 75 N.m, determine the absolute maximumshear stress in each shaft. The bearings B, C, and D allow free rotation of the shafts,and the motor holds the shafts fixed from rotating
This engine is used in a hoist. Motor 2.5 kWwith the help of gears with a power of and n = 500 rpm.transmits. If the shear strength of the AB shaft is τa = 160 MPa;a) Find the diameter of AB shaft with 1.4 times safety.b) Find the maximum force F the engine can carry.
A cylindrical steel pressure vessel has hemispherical emd caps. The inner radiuos of the vessel is 24 in anf the wall thickness is constant at o.25 in. When the vessel is presseured to 125 psi determine the following. A. The stresses of the cylinder r and hemispgerical caps. B. Based from the allowable working pressure of the blvessel solved in item a, if the pressure is increased to 250 psi what shall be the uniform thickness of the tank
A solid shaft is subjected to a twisting moment of 150 kNm. If the angle of twist is 8º per meter of the shaft and the shear stress is not to exceed 550 MPa. Determine the suitable shaft diameter by comparing the strength design and rigidity design. Also, determine the maximum shear strain acting on the shaft. Take G 250 GPa. Diameter of shaft based on Strength design is in mm Diameter of shaft based on rigidity design is in mm The sutable Diameter of the shaft is in mm The maximum shear strain is
What is the minimum diameter of a solid steel shaft that will not twist through more than 6° in a 15-m length when subjected to a torque of 8 kN·m? Use G = 83 GPa.How can you make stress of the element (rho=55mm) in question be equal to 45MPa? Prove your answer
The cylinder head of the gas engine has a dimension of a 254 mm x 450 mm. There are ten (10) bolts on the block. The explosion pressure is 14 kg/cm² and the studs are made of ordinary bolt material, with Sy = 606,760 kPa Find the stress area in in².