The vertical shaft with a diameter of d = 21 mm is supported by a thrust collar that rests on a 17-mm-thick plate. The thrust colla 11-mm thick. Assume that the load P causes a compressive stress of 150 MPa in the shaft. If the bearing stress between the thru collar and the plate is limited to 33 MPa, determine the minimum outer diameter Dollar that must be used for the thrust collar. Thruet collar area

The vertical shaft with a diameter of d = 21 mm is supported by a thrust collar that rests on a 17-mm-thick plate. The thrust colla 11-mm thick. Assume that the load P causes a compressive stress of 150 MPa in the shaft. If the bearing stress between the thru collar and the plate is limited to 33 MPa, determine the minimum outer diameter Dollar that must be used for the thrust collar. Thruet collar area

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The bar is connected to the support using a pin having a diameter of d = 1 in. If the allowable tensile stress for the bar is 1st2allow = 20 ksi, and the allowable bearing stress between the pin and the bar is 1sb2allow = 30 ksi,determine the dimensions w and t so that the gross area of the cross-section is wt = 2 in2 and the load P is a maximum. What is this maximum load? Assume the hole in the bar has the same diameter as the pin.
The d = 17-mm-diameter solid rod passes through a D = 22-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 12 mm. The rod head has a diameter of a = 34 mm, and the head has a thickness of t = 10 mm. The shear stress in the rod head cannot exceed 145 MPa, the punching shear stress in the support plate cannot exceed 95 MPa, and the bearing stress between the rod head and the support plate cannot exceed 135 MPa. Determine the maximum value of Pmax that can be supported by the structure.
The five-bolt connection must support an applied load of P = 1800 lb. If the average shear stress in the bolts must be limited to 47 ksi, determine the minimum bolt diameter that may be used for this connection.
The plastic 50-mm diameter rod is placed in a 51-mm-diameter hole with rigid walls. Determine the change in the length of the rod after the 8 kN load is applied. Use E = 40 MPa and v=0.45 for the rod.
The cylindrical pressure vessel with hemispherical end-caps is made of steel. The vessel has a uniform thickness of 0.02R mm and an outer diameter of 0.444R mm. When the vessel is pressurized to 0.004R MPa, determine the change in the overall length of the vessel. Use E = 200 GPa and µ = 0.3 for steel. Neglect localized bending. Note R=993
Topic: MACHINE DESIGN A submersible cylinder used in research has a cylindrical pressure hull of outside diameter 3.0 m and a wall thickness of 150 mm. It is constructed of an aluminum alloy, having a yield point of 450 MPa. Determine the tangential stress, in terms of MPa, in the cylindrical portion of the pressure hull whenthe vehicle is at its operating depth of 5500 m below the surface of the sea. Consider sea water to have a specific weight of 104 N/m3
The aluminum pipe shown in Fig. is used to support a load of 150 kip.Determine the maximum displacement at the top of the pipe if the load is(a) applied gradually, and (b) applied by suddenly releasing it from the topof the pipe when h = 0. Take Eal = 10(103) ksi and assume that thealuminum behaves elastically.
The horizontal bar shown is pinned at O and is supported with a helical springat L1 from O. L1=2m, L2=1m. The spring has 30 turns and the diameter of the wire usedis 20mm. The diameter of the spring is 125mm. Modulus of Rigidity = 83GPa. Determine the shear stress of the helical spring loaded as shown if w = 25kN/m.
The vertical steel rod has a constant diameter of 32 mm and a length of 400 mm. is hanged from a rigid fixing. A mass is gently placed onto a collar which is attached to the lower end of the rod. The strain energy stored in the steel is 0.400 x 10-³. If Esteet = 209 GPa, 1.1 Determine the gradually applied load and magnitude of the mass. 1.2 Calculate the maximum stress in the rod when gradually applied. 1.3 Determine the magnitude of the mass when the mass is suddenly applied. 1.4 Calculate the extension of the rod when suddenly applied.
If the allowable tensile stress for the bar is 1st2allow = 21 ksi, and the allowable shear stress for the pin is tallow = 12 ksi, determine the diameter of the pin so that the load P will be a maximum. What is this load? Assumethe hole in the bar has the same diameter d as the pin. Take t = 1 4 in. and w = 2 in.
The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (sY)st = 640 MPa, and for the bronze (sY)br = 520 MPa,determine the magnitude of the largest elastic load P that can be applied to the assembly. Est = 200 GPa, Ebr = 100 GPa.
A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside of a 50 mm diameter solid steel rod. If the compound bar is then subjected to an axial compressive load of 160 kN determine the load carried by the steel rod and the brass bush and the compressive stress set up in each material. For steel, E = 210 GN/m2; for brass, £ = 100 GN/m2