Three forces of magnitude P1, P2 and P3 are applied as shown figure to the end (D) of the member (CD), which is connected to a solid shaft (CE) of radius (r=20 mm). Knowing that the distance from (D) to the axis of shaft (CE) is 400 mm, and point (A) is located at a distance 200 mm from the end (C). Assuming that all stress remain below the proportional limit of the material. Note: P1, P2 and P3 are assigned for each student as in the table provided. Answer the following questions. (a) Determine the principal stresses and principal planes, maximum shearing stress at point A located on the surface of the shaft (CE) at the x-axis.

Three forces of magnitude P1, P2 and P3 are applied as shown figure to the end (D) of the member (CD), which is connected to a solid shaft (CE) of radius (r=20 mm). Knowing that the distance from (D) to the axis of shaft (CE) is 400 mm, and point (A) is located at a distance 200 mm from the end (C). Assuming that all stress remain below the proportional limit of the material. Note: P1, P2 and P3 are assigned for each student as in the table provided. Answer the following questions. (a) Determine the principal stresses and principal planes, maximum shearing stress at point A located on the surface of the shaft (CE) at the x-axis.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two forces P can be applied separately or at the same time to a plate that is welded to a solid circular bar of radius r. Determine the largest compressive stress in the circular bar (a) when both forces are applied, (b) when only one of the forces is applied.
A force of 90 N is applied on a lever AB as shown in the figure. Knowing that the lever is 225 mm long and that the moment of force in relation to point B is 13.5 N.m clockwise, determine the value of α.
A tower shown in the figure above is powered by AB and AC cables. A worker of the tower A 12m long rigid rope ties to point A (| AE | = 12m) and applies a constant force of 120N to the rope. The angle between the tower and the AE rope is 30 °. The pull of cables and rope applied to point A Knowing that the sum (combination) of the forces is in the downward direction (along the y-axis) (point O is the origin); 1) type the until vector of the force on the AE rope in θ. 2) if the checks on the AB and AC cable required to be equal, what should be the angle ? 3) if the pull force on the AB cable desired to be maximum, 0 < θ < 180 angel calculate. 4) θ = 30 + 9x4= 66 a) find the severity of the force on the AB cable (TAB) b) find the severity of the force on the AC cable (TAC).
Four plates, each being 15 mm thick, are to be connected by six bolts of 19 mm diameter as shown. Consider B = 181 mm. Assume that the force is equally distributed among the rivets. A. Determine the minimum force P (Newtons) if the allowable bolt shearing stress is 33 MPa. B. Determine the minimum force P (Newtons) if the allowable plate bearing stress is 32 MPa. C. Determine the tensile stress of the top plate (MPa) at segment a-a if the force P is 35 kN.
The two forces shown are applied to a rigid plate supported by a steel pipe of 8-in. outer diameter and 7-in. inner diameter. Determine the value of P for which the maximum compressive stress in the pipe is 15 ksi
Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. The steel rod has a length of 300 mm while the brass rod has a length of 200 mm. The diameters of the rods are shown in the figure below. A force of 60 kN is applied at point B of the steel segment. For the loading shown and knowing that modulus of elasticity values for steel and brass are respectively Es = 200 GPa and Eb = 105 GPa, determine a.) The reactions at A and E: RA and RE. b.) The deflection of point C from its original location. how to do
To determine the state of stress in a solid rod using the principle of superposition. A solid rod has a diameter of e� = 55 mmmm and is subjected to the loading shown. Let a� = 200 mmmm , b� = 220 mmmm , c� = 350 mmmm , d� = 250 mmmm , and P� = 3.0 kNkN . Take point A to be at the top of the circular cross-section. As shown (Figure 2), a cut was made at A to determine the resultant internal loadings. Determine the moment about the x axis, Mx��. b) Part B - Moment about the z axis at A Part C - Stress due to the normal force To find the state of stress at A, the principle of superposition must be used. If the rod has a diameter of 55 mm , find the stress σA�� due to the normal force. Part D - Stress due to the bending moment about the x axis To find the state of stress at A, the principle of superposition must be used. If the rod has a diameter of 55 mm , find the stress σA�� due to the bending moment about the x axis.
A fabric used in air-inflated structures is subjected to a biaxial loading that results in normal stresses ox = 18 ksi and oz = 24 ksi.Knowing that the properties of the fabric can be approximated as E = 12.6 x 10 psi and v = 0.34, determine the change in length of (a) side AB, (b) side BC, (c) diagonal AC.
Structural members A and B are riveted to the support that shown in the figure. If both elements are known to be in compression and that the force in member A is 10 kN and in member B is 15 kN, determine by trigonometry the magnitude and direction of the result amount of the forces applied to the support by members A and B.
A cast-iron machine part is acted upon by the 3 kN-m couple shown. Know-ing that E= 165 GPa and neglecting the effect of fillets, determine (a) the maximum tensile and compressive stresses in the casting and (b) the radius of curvature of the casting
When the force P reached 8 kN, the wooden specimen shown failed in shear along the surface indicated by the dashed line. Determine the average shearing stress along that surface at the time of failure.
A circular shaft AB consists of a 10-in.-long, 78-in.-diameter steel cylinder, in which a 5-in.-long, 58-in.-diameter cavity has been drilled from end B. The shaft is attached to fixed supports at both ends, and a 90 lb?ft torque is applied at its midsection . Determine the torque exerted on the shaft by each of the supports.