i need the answer quickly (B) Numerical ProblemsTwo plates 10 mm thick are joined by single riveted lap joint. The diameter of the rivets is20 mm and pitch = 60 mm. If o, = 125 N/mm2, t = 80 N/mm2 and o, 160 N/mm2, determine theefficiency of the joint.(Ans. 33.51%]nm dotormine:

Answered: Image /qna-images/answer/cc3be713-e3fa-411f-94ac-14068763ae25.jpg

Answered: Two plates 10 mm thick are joined by…

Engineering

Mechanical Engineering

Two plates 10 mm thick are joined by single rive 20 mm and pitch = 60 mm. If g, = 125 N/mm², t = 80

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The bottom of a steel "boat" is a 5.00 mm ×× 9.00 mm ×× 2.00 cmcm piece of steel (ρsteel=7900kg/m3)(ρsteel=7900kg/m3). The sides are made of 0.550 cmcm -thick steel. To do this problem, assume that the bottom of the boat is the full dimensions, but that the sides of the boat are welded onto the top of the bottom (so the total side height is the height of the side plus the thickness of the bottom). h= ? cm
The bottom of a steel "boat" is a 5.00 mm ×× 9.00 mm ×× 2.00 cmcm piece of steel (ρsteel=7900kg/m3)(ρsteel=7900kg/m3). The sides are made of 0.550 cmcm -thick steel. To do this problem, assume that the bottom of the boat is the full dimensions, but that the sides of the boat are welded onto the top of the bottom (so the total side height is the height of the side plus the thickness of the bottom). Find the h ( cm)
Two steel bars (Es=200 GPa and αs=11.7 3 10–6/°C) are used to reinforce a brass bar (Eb=105 GPa, αb=20.9 3 10–6/°C) that is subjected to a load P5 25 kN. When the steel bars were fabricated, the distance between the centers of the holes that were to fit on the pins was made 0.5 mm smaller than the 2 m needed. The steel bars were then placed in an oven to increase their length so that they would just fit on the pins. Following fabrication, the temperature in the steel bars dropped back to room temperature. Determine (a) the increase in temperature that was required to fit the steel bars on the pins, (b) the stress in the brass bar after the load is applied to it.
Calculate the axial stresses of Galvani pipe, σg.Given the load, P is 12 kN, cross-sectional area of bronze pipe, Ab is 8.92 m2, crosssectional area of galvani pipe, Ag is 1.03 m2, modulus of elasticity of bronze, Eb is 10 MPa and modulus of elasticity of galvani Eg is 60 MPa.
A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a torque of 8 kNm is applied to the shaft, what is the maximum stress in the weld?.
An aluminum [E = 10,000 ksi] control rod with a circular cross section must not stretch more than 0.22 in. when the tension in the rod is 2100 lb. If the diameter of the rod is 0.372 in., determine the maximum length of the rod.
Sketch a tensile member with (a) a rectangular crosssection, (b) a solid circular cross section, and (c) a circulartubecross section, and label the dimensions symbolically (e.g.,label the radius for the solid circular case). For each member, write out the definition of engineering stress in terms of the actual dimensions of the component. If therectangular member has dimensions of width and thicknessequal to 1 cm 0.3 cm, what would be the radius of a solidcircular member such that the stress is equal for an equaltensile load? If a tube has an outer radius equal to that ofthis same solid cylinder, what is the maximum inner radiussuch that the stress does not exceed 200% of the stress inthe solid cylinder?
A disk of SBR elastomer 3.0 cm in diameter 0.5 cmthick is used as a cushioning surface between two steel rods ofthe same diameter, as shown below (not to scale). a. If the rods are brought together with an axial force of 100 N such that the SBR is compressed elastically between them, what is the thickness of the SBR under load? b. Under the same conditions as part (a), what is the greatest possible diameter of the SBR under load? c. If the SBR is bonded to the rods, how far can one rod be rotated with respect to the other before the SBR/rod interface fractures? Assume that the rods are essentially rigid and the distance between them remains constant. Please answer in degrees of rotation.
A lap joint shown is made by two identical plates that are connected by nine 15-mm diameter rivets. The diameter of each hole is 18 mm. Assume that the force P is equally distributed among the rivets. (t = 20mm) A. What is the maximum force in Newton if the shear stress of the rivets is limited to 5 MPa and the bearing stress between each rivet and a plate is 6 MPa? B. If the force P-20 KN, what is the tensile stress in MPa at section a-a of the top plate?
(D) Seven circular cross-section rivets (Dia.=16 mm) are used to fix a lap joint of steel plates under single shear action. If the rivets are made from Aluminium (E=80 GPa) and the plates under tension of 15 kN. Solve this problem to show weather this joint is safe or not. Suppose all the rivets have equal load share.
A sheet metal cutting machine cuts the sheet metal via shear force, V as shown in Fig. 1. The crosssection of sheet metal is rectangular with width, b = 3m and thickness, d = 5mm. The sheet metal ishaving yield strength σy = 220 MPa; Young’s modules, E = 200 GPa and Poisson’s ratio, ν = 0.3.Conduct the following analyses at the state of stress when maximum stress reaches σy and beforeshearing commences. a. At the MOST CRITICAL POINT of the sheet metal, calculate the stress state and sketch thecorresponding stress element b. If SAFETY FACTOR = 2 is considered, what is the MINIMUM shear force, V required tocut the sheet metal according to following criterions? i. ii. Tresca criterion?von Mises criterion? c. Sketch the YIELD LOCI for both cases above. d. As a sheet-metal engineer, which failure criterion in (b) will you use to determine the cuttingshear force? Explain the reason for your answer.
A 5.0m long steel wire has a cross-sectional area of 0.55cm^2. Its proportional limit has a value of 0.0018 times its Young's modulus. Its breaking stress has a value of 0.0065 times its Young's modulus. The wire is fastened at its upper end and hangs vertically. a. How great a weight can be hung from the wire without exceeding the proportional limit? b. How much will the wire stretch under this load? c. What is the maximum weight that the wire can support?