Using the DC operating conditions from the following table, give the noise margin HIGH (NMH) for the 74HC logic family with Vcc=+3.4v.DC Operating Conditions for a Sample of 7400 Series Logic FamiliesDC Operating ConditionLogicFamilySpeed(MHz)YearVcc VOHmax VOHmin VOLmax VOLmin VIHmax VIHminILmax VILminIclomax (H/L)Orig. (TTL) 1964+5+5+2.4+0.4GND+5+2+0.8GND40m-4/+16m25LS (TTL) 1976+5+5+2.4+0.4GND+5+2+0.8GND8.8m-4/+8m40HC (CMOS) 1982 +2-6Vcc0.8.Vcc 0.33GNDVcc0.7.Vcc 0.3.Vcc GND40u+/-25m50AC (CMOS) 1985 +2-6Vcc0.8.Vcc 0.33GNDVcc0.7 Vcc 0.3.Vcc GND80u+/-50m125Note 1: All voltage specifications have units of volts. All current specifications have units of amps.Note 2: The Vo and V, specifications for the AC and HC logic families are worst case and varydepending on the Vcc selection and the output current.Note 3: All specifications are given for the commercial temperature range (74 series).1.17v0.5v0.34v0.4v

Given that, VOHmax=2.4 VIHmin=2 A Noise margin is the amount of noise that CMOS can withstand…

Answered: Using the DC operating conditions from…

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

An industry has 4 shareholders(W,X,Y,Z). 35 percent, 30 percent ,25 percent and 10 percent are the % of shares held by the shareholders, respectively.60 percent or above of the stack of full support is required for any main decision to be taken in the industry. Hint: Voting power of shareholders = Shares held by them i.In logic circuit designing, explain the reason why NOR and NAND gates are greatly preferred ii. Mention all the ways used in designing the logic gate in a form of logical steps
An industry has 4 shareholders(W,X,Y,Z). 35 percent, 30 percent ,25 percent and 10 percent are the % of shares held by the shareholders, respectively.60 percent or above of the stack of full support is required for any main decision to be taken in the industry. Hint: Voting power of shareholders = Shares held by them i.Using only NAND gates illustrate how the circuit could be implemented. ii.Considering the voting in the industry, there should be a designation of a combinational logic circuit.(Note the design should relate to the voting in the industry)
A certain packaged IC chip can dissipate 5W. Supposewe have a CMOSIC design that must fit on onechip and requires 10 million logic gates. What is theaverage power that can be dissipated by each logicgate on the chip? If the average gate must switch at100 MHz, what is the maximum capacitive load ona gate for VDD =3.3 V, 2.5 V and 1.8 V.
An equation in reduced SOP form is F=AB+B'C+A'C' I need to figure out how to draw a logic circuit using NAND gates. I'm not sure how to represent that. Thank you.
Implement a circuit that has two data inputs (A and B), two data outputs (C and D), and a control input (S). If S equals 1, the network is in pass-through mode, and C should equal A, and D should equal B. If S equals 0, the network is in crossing mode, and C should equal B, and D shouldequal A. Draw the circuits using the standard logic gates (NAND, NOR, NOT, etc) as needed. Explain the working of the circuit.
29. The following figure shows the circuit design of logic operations. Select a FALSE statement. answer choices: If GPIO pin 12 is LOW and GPIO pin 16 is HIGH, then only LED_B is on. If GPIO pin 12 is HIGH and GPIO pin 16 is HIGH, then only LED_Y is on. If GPIO pin 12 is HIGH and GPIO pin 16 is LOW, then only LED_A is on. If GPIO pin 12 is LOW and GPIO pin 16 is LOW, the all LEDs are off.
Select a suitable logic family, which has extremely low power consumption. (a) CMOS logic family (b) Emitter coupled family (c) Transistor – Transistor logic (d) None of the above
ASAP. will upvote and leave positive remark Q1.1. Draw the logic diagram that implements the complement of the following function F(A,B,C,D) = ∑(0,1,2,3,6,10,11,14) a) NAND logic diagram b) NOR logic diagram Q1.2. Simplify the following function, and implement them with two-level NOR gate circuits: F(w,x,y,z) = wx’ + y’z’ + w’yz’ Q1.3. Implement the following Boolean expression with exclusive-OR and AND gates: F(A,B,C,D) = AB’CD’ + A’BCD’ + AB’C’D + A’BC’D
Given the expression F = A’B + CD + {(A+B)’ [(ACD) + (BE)’]} ,draw its logic implementation using the basic logic gates. Then use NAND gates, NOR gates, or combinations of both to implement the same expression
Course: DigitalLogic Design Please solve this question in a 2 hour. Solve it step by step clearly: Obtain the simplified expression of a given function in product of sum (POS) form. Also draw logic diagram of simplified expression using OR-Nand gate and NOR Implementation. F(x,y,z)= Product (0,1,4,5)
for the following logic equation ,F(a,b,c) = abc+ a’+ b’+ c’, Determine the following : Draw circuit using basic Logic gate. Draw circuit using NAND gate only. Draw circuit using NOR gate only.
Design transistor level circuits for a 4-bit even parity generator using (i) CCMOS logic (ii) pseudo-nmos logic (iii) pass transistor logic, (iv) transmission gate logic.

SEE MORE QUESTIONS

Recommended textbooks for you

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

SEE MORE TEXTBOOKS