w A simply supported beam is subjected to the load distribution shown in figure, which is symmetrical about the middle of the beam. What would be the reactions at the supports? (Use SI system if your roll number is less than or equal to 100 and use US customary system if your roll number is greater than 100). (Roll No 196) Also replace this force by an equivalent force couple system at the right edge of the beam if your roll number is odd and replace this force by an equivalent force couple system at the left edge of the beam if your roll number is even. The load type is Elliptical, w. = 415 L = Any value of your choice 2L Figure for Question No.1

w A simply supported beam is subjected to the load distribution shown in figure, which is symmetrical about the middle of the beam. What would be the reactions at the supports? (Use SI system if your roll number is less than or equal to 100 and use US customary system if your roll number is greater than 100). (Roll No 196) Also replace this force by an equivalent force couple system at the right edge of the beam if your roll number is odd and replace this force by an equivalent force couple system at the left edge of the beam if your roll number is even. The load type is Elliptical, w. = 415 L = Any value of your choice 2L Figure for Question No.1

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter4: Shear Forces And Bending Moments

Section: Chapter Questions

Problem 4.3.25P: Frame ABC has a moment release just left of joint B. Find axial force N, shear force V, and moment M...

See similar textbooks

Similar questions

Repeat Problem 6.4-14 but use the configuration of channel shapes and loading shown in the figure. Use P = 250 N.
A seesaw weighing 3 lb/ft of length is occupied by two children, each weighing 90 lb (see figure). The center of gravity of each child is 8 ft from the fulcrum. The board is 19 ft long, 8 in. wide, and 1.5 in. thick. What is the maximum bending stress in the board?
Repeat Problem 9,5-15 for the anti-symmetric loading shown in the figure.
Frame ABC has a moment release just left of joint B. Find axial force N, shear force V, and moment M at the top of column AB. Write variables N, V, and M in terms of variables P and L.
At a full d raw, an archer applies a pull of 130 N to the bowstring of the bow shown in the figure. Determine the bending moment at the midpoint of the bow.
Repeat Problem 10.4-41 for the loading shown in the figure.
Repeat Problem 6.2-1 but now assume that the steel plate is smaller (0.5 in. × 5 in.) and is aligned with the top of the beam as shown in the figure.
The figure shows a cantilevered beam, subjected to a uniformly distributed (rectangular) 40 N/m force along the section DE, a 50 N point force at point C, and a 200 Nm couple moment. a. Write the shear-force and bending-moment equations as a function of distance, x, measured from the leftmost point, A, for the entire beam. b. Using your shear-force and bending-moment equations, calculate the shear force and bending moment at x = 2 m and x = 5 m. 200 N·m A 2.5 m 50 N CV D 1 m 40 N/m ↓↓↓ 2.5 m E B 2 m
In Figure Q3a, a beam is supported at A and C with a uniformly distributed load of20 kN/m between A and B. Draw and label the shear force diagram (SFD) andbending moment diagram (BMD) for the beam shown in Figure Q3a. Label thevalues for shear force and bending moment at points A, B, C & at the beam midpoint M; the maximum bending moment and its distance from A; and clearlyindicate the type of bending between AB and between BC
problem 3 Find the Shear Moment Diagram of the following problems usingONLY AREA METHOD.
In Figure 4a, a beam is supported at A and C with a uniformly distributed load of 20 kN/m between A and B. Draw and label the shear force diagram (SFD) and bending moment diagram (BMD) for the beam shown in Figure Q3a. Label the values for shear force and bending moment at points A, B, C & at the beam mid-point M; the maximum bending moment and its distance from A; and clearly indicate the type of bending between AB and between BC. (show all work)
In Figure Q5b, a beam is supported at A and C with a uniformly distributed load (UDL) of 38.75 kN/m between A and B. Distance L1 = 9.00 m and L2 = 4.50 m. Draw and label the shear force diagram (SFD) and bending moment diagram (BMD) for the beam shown in Figure Q5b. Label the shear force and the bending moment values at points A, B & C on both diagrams; determine the distance from A along the beam where the shear force is zero; and calculate the bending moment at the point where the shear force is zero. Clearly indicate the type of bending between AC and between BC. A UDL L1 Figure Q5b B L2 C