Water at 20°C and p = 998 kg/m³ flows through a 5-cm-diameter pipe that has a 180° vertical bend, as in Figure 6. The total length of pipe between flanges 1 and 2 is 105 cm. When the weight flow rate is 240 N/s, P, = 185 kPa and P, = 154 kPa. Neglecting %3D pipe weight, determine the total force that the flanges must withstand for this flow to carry on. Assume P = 101 kPa.

Water at 20°C and p = 998 kg/m³ flows through a 5-cm-diameter pipe that has a 180° vertical bend, as in Figure 6. The total length of pipe between flanges 1 and 2 is 105 cm. When the weight flow rate is 240 N/s, P, = 185 kPa and P, = 154 kPa. Neglecting %3D pipe weight, determine the total force that the flanges must withstand for this flow to carry on. Assume P = 101 kPa.

Name: (c) Water at 20°C and p = 998 kg/m³ flows through a 5-cm-diameter pip
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: (c) Water at 20°C and p = 998 kg/m³ flows through a 5-cm-diameter pipe that has a 180°vertical bend, as in Figure 6. The total length of pipe between flanges 1 and 2 is 105cm. When the weight flow rate is 240 N/s, P, = 185 kPa and P, = 154 kPa. Negl

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the system-Water at 20°C flows by gravity through a smooth pipe fromone reservoir to a lower one. The elevation difference is 60 m.The pipe is 360 m long, with a diameter of 12 cm. A pump, which delivers15,000 W to the water, is used at night to refill the upper reservoir. The pipe diameter is increased from 12 cm toprovide more flow. If the resultant flow rate is 90 m3/h, estimatethe new pipe size.
Water at 20°C is to be pumped through 2000 ft of pipe fromreservoir 1 to 2 at a rate of 3 ft3/s, as shown in Fig. P6.62.If the pipe is cast iron of diameter 6 in and the pump is75 percent efficient, what horsepower pump is needed?
Water (@ 75°C) flows at a horizontal pipe at a rate of 1.6 m3/min in a pipe. Flow enters a 3 inch 45 deg. elbow and diverted upwards into a connecting pipe. The diameter of the outlet is 2 inches. If the pressure just before the elbow is 78kPa, what is the magnitude and direction of the force to keep the elbow in place? Assume: that frictional losses in the elbow are negligible.
Water at 20 ° C flows through a 5-cm-diameter pipe that hasa 180 °vertical bend, as in Fig. P3.43. The total length ofthe pipe between flanges 1 and 2 is 75 cm. When the weightflow rate is 230 N/s, p 1 = 165 kPa, and p 2 = 134 kPa.Neglecting pipe weight, determine the total force that thefl anges must withstand for this flow.
Write legibly 2. Water is to be siphoned from a tank at the rate of 0.095 m3/s. The flowing end of the siphon pipe is 4.75 m below the water surface. The lost head terms are 1.5V 2/2g from tank to summit of siphon and 1.25V 2/2g from summit to end of siphon. The summit is 1.5 m above the water surface. Determine (a) the diameter of the pipe required for the siphon and (b) thepressure at the summit 2. a. diameter of pipe ____________ mm 1b. pressure at the summit______________ 2 kPa
Air flows steadily from a tank pressurized to 3kPa through a pipe of diameter D = 0.03 m and finally discharges to the atmosphere through a nozzle of diameter 0.01m. If the specific weight of air is 12 N/m^3 the air flow rate is?
A hydroelectric power generating system is shown in the figure. Water flows from an upper reservoir to a lower one passing through a turbine at the rate of 286 liters per second. The total length of pipe connecting the two reservoirs is 186 m. The pipe diameter is 346 mm and the Hazen-Williams coefficient is 129. The water surface elevations of reservoirs 1 and 2 are 194 m and 69 m, respectively. Determine the power in kW required by the turbine if it is 63% efficient? Neglect minor losses. Round your answer to 3 decimal places.
6 cm-diameter commercial steel pipeline is used to transport water at 10⁰C from a reservoir to a free discharge point. The pipeline consists of 85 m straight pipe, 2 wide open gate valves, 1 wide open angle valve, 4 standart 90⁰ elbows, 1 entrance from a reservoir and 1 free discharge. The elevation of the entrance is 10 m while the elevation of the discharge is 35 m. The inlet pressure is 20 psig and exit pressure is 0 psig. A pump is installed in the line to move the water. Calculate the pump work (J/kg) so the volumetric flow rate will be Q= 0.01 m3/s. (1 psi = lbf/in2).
A fully-filled open storage tower of height 32 m and diameter 3.0m supplies water to a house. A horizontal pipe at the base of the tower has a diameter of 2.54cm. To satisfy the needs of the home, the supply pipe must be able to deliver water at a rate of 0.67 gal/s. a. If water were flowing at the maximum rate, what would be the pressure in the horizontal pipe?b. A smaller pipe, of diameter 1.27 cm supplies the second floor of the house, a distance of 7.2 m above the ground level. What are the flow speed and water pressure in this pipe?
4. Hydroelectric plants in the mountains bring water from a reservoir down to a turbine through enclosed tubes. In such plants, the 100 cm diameter intake tube (Point 2) in the dam is 50m below the water surface (Point 1) of the reservoir. The water drops 200 m through the tube before flowing into the turbine through a 50 cm diameter nozzle.
A Francis radial-flow hydroturbine has the following dimensions, where location 2 is the inlet and location 1 is the outlet: r2 = 6.60 ft, r1 = 4.40 ft, b2 = 2.60 ft, and b1 = 7.20 ft. The runner blade angles are ?2 = 82° and ?1 = 46° at the turbine inlet and outlet, respectively. The runner rotates at n. = 120 rpm. The volume flow rate at design conditions is 4.70 ×106 gpm. Irreversible losses are neglected in this preliminary analysis. Calculate the angle ?2 through which the wicket gates should turn the flow, where ?2 is measured from the radial direction at the runner inlet. Calculate the swirl angle ?1, where ?1 is measured from the radial direction at the runner outlet. Does this turbine have forward or reverse swirl? Predict the power output (hp) and required net head (ft).
A horizontal water pipe diameter 15 cm converges to 7.5 cm diameter. If the pressures at the two sections are 4 kg/cm2, and 1.5 kg/cm2 respectively, calculate the flow rate of water.