You have a 16-bit timer and you want to configure it to generate an interrupt at a rate of 500 Hz. The clock input to the timer is configured at 1 MHz and a clock divider value of 1. At what count value should the interrupt be called and the timer reset? (This would be the equivalent of the value loaded into the CCRO register with a Timer A peripheral in Up mode on our MSP430)

You have a 16-bit timer and you want to configure it to generate an interrupt at a rate of 500 Hz. The clock input to the timer is configured at 1 MHz and a clock divider value of 1. At what count value should the interrupt be called and the timer reset? (This would be the equivalent of the value loaded into the CCRO register with a Timer A peripheral in Up mode on our MSP430)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

6.) Select all the 8088 input signals that can cause the microprocessor to take an interrupt. a.) OSC b.) INTA c.) NMI d.) READY e.) INTR f.) IRQ 7.) Given the 8088 instruction "INT nn", how many possible types of interrupts are there for the 8088? a.) 2 b.) 4 c.) 8 d.) 256
1)Write a program in 8051 to copy the contents of registers R0 to R7 into internal RAM addresses 40H to 47H respectively using PUSH instructions. Assume Register Bank 0 is selected. 2 )Designa Programmable timer using 8254 and 8086 to generate a square wave of period 5 millisecond. Interface 8254 at the address 0040H for Counter 0 and write the assembly language program. The 8086 and 8254 runs at 6 megahertz and 3 megahertz respectively.
Frame the command words ICW1, ICW2, ICW3 and OCW1 for initializing a single 8259to initiate INT 40H to INT 47H in an 8086 based system. The desired features are level triggered interrupt and automatic end of interrupt.
Please show work included 6. Assume a digital to analog conversion system uses a 7-bit integer to represent an analog temperature over a range of -27oF to 100oF. If the actual temperature being read was 40oF, what would be the closest possible value that the system could represent? Write the answer in a 7-bit binary number as well as in decimal. The answer should be in the following form 00010001 and -10oF a set of two numbers.
A simple burglar alarm is to be wired up in a house which has two access doors, A and B. Micro switches are used todetect whether the doors are open or closed with a logic level 0 detected when a door is closed and a logic level Itransmitted when a door is open. The alarm system can also be activated ON and OFF through a concealed manualswitch S. with the system activated; a logic level I is transmitted through switch S. A logic level 0 through switch Sindicates that the system is OFF Devise an appropriate Boolean expression to represent the sound of the alarm Fwhen the system is activated and either, or both, of the doors are opened. construct a circuit diagram for the alarm system and deduce the appropriateBoolean functions:(a) Using NAND gates only.(b) Using NOR gates only
30. The following statements describe the results of 4-to-10 decoder operations. Select a FALSE statement based on your hands-on activity results. answer choices: If the binary inputs are 1000 (decimal 8), only the DEC output D8 (IC pin 10) will be TRUE. If the binary inputs are 0001 (decimal 1), only the LED connected GPIO pin 21 will be on. If the binary inputs are 0000 (decimal 0), no DEC outputs will be TRUE. If the binary inputs are 0000 (decimal 0), all the LEDs will be off.
For a PIC24, What values of PRE and PR2 are needed to enable Timer2 to generate an interrupt every 320 ms? Assume that internal clock is used and it has a value of 40 MHz.
A reset input is used in IC 7493, why? a. For reset the counter b. For setting the counter c. For decrement of bit by 1 d. For increment of bit by 1
Using Timer Interrupt, Write the code of the microcontroller program for Arduino IDE for a system that sends time information to the serial port in "Hour:Minute: Second" format once every second.
You are given the following assembly language statements: MOV AX, 15225 MOV BL, 126 DIV BL SUB BL, AL Just after the CPU finishes executing the SUB instruction, calculate the following: i)The decimal values in AL, AH, and AX registers ii)The decimal value of BL iii)The values of flag bits: Sign, Carry, Auxiliary, Zero, Parity, and Overflow.
Write a program to PUSH R0, R1, and R3 of Bank 0 onto the stack and POP them back into R5, R6, and R7 of Bank 3. Also, mention the value of SP register after every PUSH and POP operation. this question is asked in microprocessor and microcontroller
simple burglar alarm is to be wired up in a house which has two access doors, A and B. Micro switches are used todetect whether the doors are open or closed with a logic level 0 detected when a door is closed and a logic level Itransmitted when a door is open. The alarm system can also be activated ON and OFF through a concealed manualswitch S. with the system activated; a logic level I is transmitted through switch S. A logic level 0 through switch Sindicates that the system is OFF Devise an appropriate Boolean expression to represent the sound of the alarm Fwhen the system is activated and either, or both, of the doors are opened.