Control Systems Engineering
7th Edition
ISBN: 9781118170519
Author: Norman S. Nise
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 1, Problem 12P
Tactile feedback is an important component in the learning of motor skills such as dancing, sports, and physical rehabilitation. A suit with white dots recognized by a vision system to determine arm joint positions with millimetric precision was developed. This suit is worn by both teacher and student to prov ide position information. (Lieberman, 2007), If there is a difference betw een the teacher's positions and that of the student vibrational feedback is provided to the student through eight strategically placed vibrolactile actuators in the wrist and arm. This placement takes advantage of a sensory effect known as cutaneous rabbit that tricks the subject to feel uniformly spaced stimuli in places where the actuators are not present. These stimuli help the student adjust to correct the motion. In summary, the system consists of on instructor and a student having their movements followed by the vision system. Their movements are fed into a computer that finds the differences between their joint positions and provides proportional vibrational strength feedback to the student. Draw a block diagram describing the system design.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A stock-flow system models the level of water in a lake. Near a certain equilibrium point, there are three feedback loops: an amplifying feedback loop with strength of +0.55 per month, a stabilizing feedback loop with strength of -0.09 per month, and an amplifying feedback loop with strength of +0.79 per month.
Calculate the strength of the overall feedback.
Sensor systems for obstacle detection and avoidance in mobile robots.
• Design and develop a suitable processor-based Data Acquisition (DAQ) system and external hardware to interface, measure, display and store the responses from the selected sensors.
How would I plot the aircraft pitch angle response to elevator step inputs of -10,
and +10 degrees for a duration of five seconds by implementing short period approximation using Simulink. What would the block diagram/ simulink layout roughly look like?
Chapter 1 Solutions
Control Systems Engineering
Ch. 1 - Prob. 1RQCh. 1 - Prob. 2RQCh. 1 - Prob. 3RQCh. 1 - Prob. 4RQCh. 1 - State one condition under which the error signal...Ch. 1 - Prob. 6RQCh. 1 - Name two advantages of having a computer in the...Ch. 1 - Name the three major design criteria for control...Ch. 1 - Prob. 9RQCh. 1 - Physically, what happens to a system that is...
Ch. 1 - Instability is attributable to what pan of the...Ch. 1 - Describe a typical control system analy sis task.Ch. 1 - Describe a typical control system design task.Ch. 1 - Prob. 14RQCh. 1 - Name three approaches to the mathematical modeling...Ch. 1 - Briefly describe each of your answers to Question...Ch. 1 - Prob. 1PCh. 1 - Prob. 2PCh. 1 - An aircraft's attitude varies in roll, pitch, and...Ch. 1 - We can build a control system that will...Ch. 1 - Prob. 5PCh. 1 - During a medical operation an anesthesiologist...Ch. 1 - Prob. 7PCh. 1 - Prob. 8PCh. 1 - The human eye has a biological control system that...Ch. 1 - A Segway ®5 Personal Transporter (PT) (Figure Pl...Ch. 1 - In humans, hormone levels, alertness, and core...Ch. 1 - Tactile feedback is an important component in the...Ch. 1 - Prob. 13PCh. 1 - Moored floating platforms are subject to external...Ch. 1 - In the Case Study of Section 1.4. an antenna...Ch. 1 - Figure Pl.5 shows the topology of a photo-voltaic...Ch. 1 - Prob. 17PCh. 1 - Prob. 18PCh. 1 - Prob. 19PCh. 1 - Prob. 20PCh. 1 - Prob. 21PCh. 1 - Contol of HIV/AIDS. As of 2012. the number of...Ch. 1 - Prob. 23PCh. 1 - Parabolic trough collector. A set of parabolic...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Help with the MATLAB code to do the following: Given an audio recording of vehicles, compute Power Spectral Density, 1/3 octave band level, octave band level, A-weighted Leq, C-weighted Leq, L10 (unweighted since sample is short), L90 (unweighted since sample is short). If the measurement is made at approximately 50 ft, and that the vehicles are moving at an average of 65 mph, what is the flow rate Q? If instead, the noise is dominated by 1-2 motorcycles, how fast are they going? Given- -The data are in counts -Calibration factor is 133 uPa/count -Sample rate is 44100Hz. -Remember that in air the dB reference is 20 uPa -Pwelch requires that the inputs are doublesarrow_forwardYou are the mechatronics engineer of a manufacturing plant. You decide to perform an analysis on a robot arm of the assembly line with the objective of optimizing its performance. After taking several readings of the speed of the arm’s end effector, you approximate its velocity to the function given below. v(t) = -t4 + 5t3 - 7t2 + 3t + 0.22 0 =< t =< 3 where the velocity is in ms-1 d) Knowing that the distance travelled by an object is the area under its velocity-time graph, determine the distance travelled by the end effector on the interval 0 =< t =< 1 by using the mid-ordinate rule. Simpson’s rule correct to 3 decimal places using four intervals. e) Calculate the same distance as in (d) above by using the appropriate definite integral. f) Compare the distances you calculated in (d) and (e) above and comment on the accuracy of the two methods you used in (d)arrow_forwardWhat is the difference between multigridding and multiblocking? Discuss how each may be used to speed up a CFD calculation. Can these two be applied together?arrow_forward
- SOLVE STEP BY STEP IN DIGITAL FORMAT Explain some methods to improve the efficiency of aircraft propulsion systems, as well as combustion techniques or the use of alternative fuels.arrow_forwardContext The needle of a sewing machine makes a repetitive up and down motion which is described by the equation y(t)=Acos(wt) To choose the settings of the device that will ensure that the needle successfully pierces the textile, you are asked to model the speed in ? of the needle as a function of time. Constraints and information The parameter A represents the range of motion (in m);The parameter w represents the angular frequency. It tells us about the number of back and forth movements that the needle makes per second;The parameter w is given in rad/s, so your calculator absolutely must be in radians mode to do the calculations in this problem;Modelization Establish the model for the y velocity of the needle as a function of time and the parameters A and w. Then test your model by calculating the speed in y of the needle at the moment and with the given parameters: Moment: 4.1 s Amplitude: 0.012 m Angular frequency: 17.9 rad/sarrow_forwardCan you walk me through using STK to verify this result? I have STK 12 for referance.arrow_forward
- MATLAB coding requiredarrow_forwardCalculating the separation and / or joining angles in the negative feedback control circuit, if any, given as Controlling (K) and Controlled G (s) = (s + 1) / (s2-4 * s + 5) Explanation: The roots of the equation (s2-4 * s + 5); s1 = 2 + 1 * j and s2 = 2-1 * j and the system Transfer Function is TF (s) = K * G (s) / (1 + K * G (s)). a. There are split angles up to (+108.435) and (-108.435) b. There are split angles as much as (+71,565) and (-71,565) c. There are conjunction angles of (+90) and (-90). D. There are separation angles as much as (+18.435) and (-18.435). E. There are no separation and convergence angles.arrow_forwardHow matlab and differential equations work together?arrow_forward
- EXPERIMENT TITLE : PID CONTROLLER IN LEVEL CONTROL SYSTEM OBJECTIVE:To demonstrate the characteristic of P,PI and PID controller response on a level controller system. Based on the topic and objective given,please make a clear introduction.arrow_forwardYou are the mechatronics engineer of a manufacturing plant. You decide to perform an analysis on a robot arm of the assembly line with the objective of optimizing its performance. After taking several readings of the speed of the arm’s end effector, you approximate its velocity to the function given below. v(t) = -t4 + 5t3 - 7t2 + 3t + 0.22 0 =< t =< 3 where the velocity is in ms-1 Use your knowledge of differentiation to sketch the velocity-time graph, clearly marking the critical points. Using the graph sketched in (a) above, estimate the velocity when t = 1.5 s Calculate the velocity of the function when t = 1.5 s by substituting to the velocity function. Compare this value to the value you estimated in b above.arrow_forwardDerive the inverse mobile kinematics for the same robot, and compute thematrix with l = 0.325 marrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Quality Control and Quality Assurance; Author: AISC Education;https://www.youtube.com/watch?v=C2PFj9YZ_mw;License: Standard Youtube License