Package: Loose Leaf For Fluid Mechanics With 1 Semester Connect Access Card
8th Edition
ISBN: 9781259638848
Author: White
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 1, Problem 1.44P
One type of viscometer is simply a long capillary tube. A commercial device is shown in Prob. C1.10. One measures the volume flow rate Q and the pressure drop
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A capillary viscometer measures the time required for a specified volume υ of liquid to flow through a small-bore glasstube, as in Fig. . This transit time is then correlated withfluid viscosity. For the system shown, (a) derive an approximateformula for the time required, assuming laminar flowwith no entrance and exit losses. (b) If L = 12 cm, l = 2 cm,υ = 8 cm3, and the fluid is water at 20 °C, what capillary diameterD will result in a transit time t of 6 seconds?
In the gap between the two plates, the lubricant flows in one direction (x) by the pressure gradient. Lubricants are incompressible Newtonian fluids, flows are laminates, and terminal effects are ignored. Find the maximum flow rate [m/s] when the pressure difference (△P/L) per unit length is 25000 Pa/m.Data: clearance between plates (B) = 6 mm, lubricant viscosity (μ) = 25 cP (1cP = 10-3 Pa·s), lubricant density (=) = 0.88 g/cm3
In the gap between the two plates, the lubricant flows in one direction (x) by the pressure gradient. Lubricants are incompressible Newtonian fluids, flows are laminates, and terminal effects are ignored. Find the maximum flow rate [m/s] when the pressure difference (△P/L) per unit length is 25000 Pa/m.Data: clearance between plates (B) = 6 mm, lubricant viscosity (μ) = 25 cP (1cP = 10-3 Pa·s), lubricant density (=) = 0.88 g/cm3
Please.. explain more easy
Chapter 1 Solutions
Package: Loose Leaf For Fluid Mechanics With 1 Semester Connect Access Card
Ch. 1 - Prob. 1.1PCh. 1 - Table A.6 lists the density of the standard...Ch. 1 - For the triangular element in Fig, P1.3,show that...Ch. 1 - Sand, and other granular materials, appear to...Ch. 1 - The mean free path of a gas, l, is defined as the...Ch. 1 - Henri Darcy, a French engineer, proposed that the...Ch. 1 - Convert the following inappropriate quantities...Ch. 1 - Suppose we know little about the strength of...Ch. 1 - A hemispherical container, 26 inches in diameter,...Ch. 1 - The Stokes-Oseen formula [33] for drag force F on...
Ch. 1 - P1.11 In English Engineering units, the specific...Ch. 1 - For low-speed (laminar) steady flow through a...Ch. 1 - The efficiency ? of a pump is defined as the...Ch. 1 - Figure P1.14 shows the flow of water over a dam....Ch. 1 - The height H that fluid rises in a liquid...Ch. 1 - Algebraic equations such as Bernoulli's relation,...Ch. 1 - The Hazen-Williams hydraulics formula for volume...Ch. 1 - For small particles at low velocities, the first...Ch. 1 - In his study of the circular hydraulic jump formed...Ch. 1 - Books on porous media and atomization claim that...Ch. 1 - Aeronautical engineers measure the pitching moment...Ch. 1 - Prob. 1.22PCh. 1 - During World War II, Sir Geoffrey Taylor, a...Ch. 1 - Air, assumed to be an ideal gas with k = 1.40,...Ch. 1 - On a summer day in Narragansett, Rhode Island, the...Ch. 1 - When we in the United States say a car's tire is...Ch. 1 - Prob. 1.27PCh. 1 - Wet atmospheric air at 100 percent relative...Ch. 1 - Prob. 1.29PCh. 1 - P1.30 Repeat Prob. 1.29 if the tank is filled with...Ch. 1 - Prob. 1.31PCh. 1 - Prob. 1.32PCh. 1 - A tank contai as 9 kg of CO2at 20°C and 2.0 MPa....Ch. 1 - Consider steam at the following state near the...Ch. 1 - In Table A.4, most common gases (air, nitrogen,...Ch. 1 - Prob. 1.36PCh. 1 - A near-ideal gas has a molecular weight of 44 and...Ch. 1 - In Fig. 1.7, if the fluid is glycerin at 20°C and...Ch. 1 - Prob. 1.39PCh. 1 - Glycerin at 20°C fills the space between a hollow...Ch. 1 - An aluminum cylinder weighing 30 N, 6 cm in...Ch. 1 - Prob. 1.42PCh. 1 - Prob. 1.43PCh. 1 - One type of viscometer is simply a long capillary...Ch. 1 - A block of weight W slides down an inclined plane...Ch. 1 - A simple and popular model for two nonnewtonian...Ch. 1 - Data for the apparent viscosity of average human...Ch. 1 - A thin plate is separated from two fixed plates by...Ch. 1 - An amazing number of commercial and laboratory...Ch. 1 - Prob. 1.50PCh. 1 - Prob. 1.51PCh. 1 - The belt in Fig. P1.52 moves at a steady velocity...Ch. 1 - A solid tune of angle 2 , base r0, and density...Ch. 1 - A disk of radius R rotates at an angular velocity ...Ch. 1 - A block of weight W is being pulled over a table...Ch. 1 - The device in Fig. P1.56 is called a cone-plate...Ch. 1 - Extend the steady flow between a fixed lower plate...Ch. 1 - The laminar pipe flow example of Prob. 1.12 can be...Ch. 1 - A solid cylinder of diameter D, length L, and...Ch. 1 - Prob. 1.60PCh. 1 - Prob. 1.61PCh. 1 - P1.62 The hydrogen bubbles that produced the...Ch. 1 - Derive Eq. (1.33) by making a force balance on the...Ch. 1 - Pressure in a water container can be measured by...Ch. 1 - The system in Fig. P1.65 is used to calculate the...Ch. 1 - Prob. 1.66PCh. 1 - Prob. 1.67PCh. 1 - Prob. 1.68PCh. 1 - A solid cylindrical needle of diameter d, length...Ch. 1 - Derive an expression for the capillary height...Ch. 1 - A soap bubble of diameter D1coalesces with another...Ch. 1 - Early mountaineers boiled water to estimate their...Ch. 1 - A small submersible moves al velocity V, in fresh...Ch. 1 - Oil, with a vapor pressure of 20 kPa, is delivered...Ch. 1 - An airplane flies at 555 mi/h. At what altitude in...Ch. 1 - Prob. 1.76PCh. 1 - Prob. 1.77PCh. 1 - P1.78 Sir Isaac Newton measured the speed of sound...Ch. 1 - Prob. 1.79PCh. 1 - Prob. 1.80PCh. 1 - Use Eq. (1.39) to find and sketch the streamlines...Ch. 1 - P1.82 A velocity field is given by u = V cos, v =...Ch. 1 - Prob. 1.83PCh. 1 - In the early 1900s, the British chemist Sir Cyril...Ch. 1 - Prob. 1.85PCh. 1 - A right circular cylinder volume v is to be...Ch. 1 - The absolute viscosity of a fluid is primarily a...Ch. 1 - Prob. 1.2FEEPCh. 1 - Helium has a molecular weight of 4.003. What is...Ch. 1 - An oil has a kinematic viscosity of 1.25 E-4 m2/s...Ch. 1 - Prob. 1.5FEEPCh. 1 - Prob. 1.6FEEPCh. 1 - FE1.7 Two parallel plates, one moving at 4 m/s...Ch. 1 - Prob. 1.8FEEPCh. 1 - A certain water flow at 20°C has a critical...Ch. 1 - Prob. 1.10FEEPCh. 1 - Sometimes we can develop equations and solve...Ch. 1 - When a person ice skates, the surface of the ice...Ch. 1 - Two thin flat plates, tilted at an angle a, are...Ch. 1 - Oil of viscosity and density drains steadily...Ch. 1 - Prob. 1.5CPCh. 1 - Prob. 1.6CPCh. 1 - Prob. 1.7CPCh. 1 -
C1.8 A mechanical device that uses the rotating...Ch. 1 - Prob. 1.9CPCh. 1 - A popular gravity-driven instrument is the...Ch. 1 - Mott [Ref. 49, p. 38] discusses a simple...Ch. 1 - A solid aluminum disk (SG = 2.7) is 2 in in...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Liquid flows out of a hole in the bottom of a tank as in FinConsider the case in which the hole is very small compared to the tank (d ≪ D). Experiments reveal that average jet velocity V is nearly independent of d, D, ? , or ? . In fact, for a wide range of these parameters, it turns out that V depends only on liquid surface height h and gravitational acceleration g. If the liquid surface height is doubled, all else being equal, by what factor will the average jet velocity increase?arrow_forwardA prototype submarine moves at velocity V, in fresh water at 20 °C, at a 2-m depth, where ambient pressure is 128 kPa. Its critical cavitation number is known to be Ca = 0.25. At what velocity will cavitation bubbles begin to form on the body? Will the body cavitate if V = 30 m/s and the water is cold (5 °C)?arrow_forwardAssume an inviscid, incompressible flow. Also, standard sea level density and pressure are 1.23 kg/m3 (0.002377 slug/ft3) and 1.01 × 105 N/m2 (2116 lb/ft2), respectively. Consider the nonlifting flow over a circular cylinder of a given radius,where V∞ = 20 ft/s. If V∞ is doubled, that is, V∞ = 40 ft/s, does theshape of the streamlines change? Explain.arrow_forward
- The open tank in Fig. contains water at 20 ° C and isbeing filled through section 1. Assume incompressibleflow. First derive an analytic expression for the water-levelchange dh / dt in terms of arbitrary volume flows ( Q 1 , Q 2 ,Q 3 ) and tank diameter d . Then, if the water level h is constant,determine the exit velocity V 2 for the given data V 1 =3 m/s and Q 3 = 0.01 m 3 /s.arrow_forwardWhen a clean glass tube with a diameter of 2 mm is immersed in water at 20 ° C, how many mm will the capillary rise occur in the glass tube? For water at 20 ° C, surface tension is given as 0.073 N / m, density 1000 kg / m3, contact angle 0 ° C and gravitational acceleration 10 m / s2.arrow_forwardAt low velocities (laminar flow), the volume flow Q through a small-bore tube is a function only of the tube radius R, the fluid viscosity ?܇, and the pressure drop per unit tube length dp/dx. Using the Buckingham pi theorem, find an appropriate dimensionless relationship. Make use of Table 1arrow_forward
- A sample of powdered zinc oxide, density 5.60g/cm 3 , is allowed to settle under the accelerationof gravity, 981 cm/sec 2 , at 25 25°C. The rate ofsettling, v, is 7.30 ×10 3 cm/sec; the density ofthe medium is 1.01 g/cm 3 , and its viscosity is 1centipoise = 0.01 poise or 0.01 g/cm sec.Calculate the Stokes diameter of the zinc oxidepowder.Problem:arrow_forwardWhen a person ice skates, the surface of the ice actuallymelts beneath the blades, so that he or she skates on a thinsheet of water between the blade and the ice.( a ) Find an expression for total friction force on the bottomof the blade as a function of skater velocity V , bladelength L , water thickness (between the blade and theice) h , water viscosity μ , and blade width W .( b ) Suppose an ice skater of total mass m is skatingalong at a constant speed of V 0 when she suddenlystands stiff with her skates pointed directly forward,allowing herself to coast to a stop. Neglecting frictiondue to air resistance, how far will she travelbefore she comes to a stop? (Remember, she iscoasting on two skate blades.) Give your answer forthe total distance traveled, x , as a function of V 0 , m ,L , h , μ , and W .( c ) Find x for the case where V 0 = 4.0 m/s, m = 100 kg,L = 30 cm, W = 5.0 mm, and h = 0.10 mm. Do youthink our assumption of negligible air resistance is agood one?arrow_forwardA tripod holding a nozzle, which directs a 5-cmdiameter stream of water from a hose, is shown. The nozzle mass is 10 kg when filled with water. The tripod is rated to provide 1800 N of holding force. A firefighter was standing 60 cm behind the nozzle and was hit by the nozzle when the tripod suddenly failed and released the nozzle. You have been hired as an accident reconstructionist and, after testing the tripod, have determined that as water flow rate increased, it did collapse at 1800 N. In your final report you must state the water velocity and the flow rate consistent with the failure and the nozzle velocity when it hit the firefighter. For simplicity, ignore pressure and momentum effects in the upstream portion of the hosearrow_forward
- A tornado is simulated by a line sink m = -1000 m2/s plus aline vortex K = 1600 m2/s. Find the angle between anystreamline and a radial line, and show that it is independent ofboth r and θ. If this tornado forms in sea-level standard air, atwhat radius will the local pressure be equivalent to 29 inHg?arrow_forwardA belt moves upward at velocity V, dragging a fi lm ofviscous liquid of thickness h , as in Fig. . Near the belt,the fi lm moves upward due to no slip. At its outer edge, thefi lm moves downward due to gravity. Assuming thatthe only nonzero velocity is υ ( x ), with zero shear stress atthe outer fi lm edge, derive a formula for ( a ) υ ( x ), ( b ) the average velocity V avg in the fi lm, and ( c ) the velocity V c forwhich there is no net flow either up or down. ( d ) Sketchυ ( x ) for case ( c ).arrow_forwardFluid mechanics, I need solutions in 15 minutes please. MCQ/Determine the horizontal and vertical components of the liquid pressure acting on the semicylindrical gate ABC, as shown in the figure. The width into the paper is 1 m. A-Fx = 257.430 kN and Fy = 59.801 kN B-Fx = 164.018 KN and Fy = 37.229 KN C-Fx = 269.894 kN and Fy = 65.526 KN D-Fx = 98.182 kN and Fy = 20.002 KN E-Fx = 234.789 kN and Fy = 52.418 kN F-Fx = 187.005 kN and Fy = 42.182 KN G-Fx = 119.956 kN and Fy = 25.550 KN H-Fx = 141.327 kN and Fy = 31.171 KN I-Fx = 288.147 kN and Fy = 69.098 KN J-Fx = 213.112 kN and Fy = 47.903 KNarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Properties of Fluids: The Basics; Author: Swanson Flo;https://www.youtube.com/watch?v=TgD3nEO1iCA;License: Standard YouTube License, CC-BY
Fluid Mechanics-Lecture-1_Introduction & Basic Concepts; Author: OOkul - UPSC & SSC Exams;https://www.youtube.com/watch?v=6bZodDnmE0o;License: Standard Youtube License