Materials for Civil and Construction Engineers (2nd Edition)
null Edition
ISBN: 9781292154411
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 1, Problem 1.47QP
(a)
To determine
Find the mean, standard deviation and the coefficient of variation of the data.
(b)
To determine
To create a control chart for the given data in spreadsheet and provide comments.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
In a ready-mix plant, cylindrical samples are prepared and tested periodically to detect any mix problem and to ensure that the compressive strength is higher than the lower specification limit. The minimum target value was set at 5,000 psi. The compressive strength data shown in Table were collected. a. Calculate the mean, standard deviation, and the coefficient of variation of the data. b. Using a spreadsheet program, create a control chart for these data showing the lower specification limit. Is the plant production meeting the specification requirement? If not, comment on possible reasons. Comment on the data scatter.
In a ready-mix plant, cylindrical samples are prepared and tested periodically to detect any mix problem and to ensure that the compressive strength is higher than the lower specification limit. The minimum target value was set at 27.6 MPa (4000 psi). The compressive strength data shown in Table were collected. Use one system of units only as specified by the instructor.a. Calculate the mean, standard deviation, and the coefficient of variation of the data.b. Using a spreadsheet program, create a control chart for these data showing the target value and the lower specification limit. Is the plant production meeting the specification requirement? If not, comment on possible reasons. Comment on the data scatter.
Establish the differences between the wear test performed on aggregates smaller than 3/4 "and the wear test performed on aggregates larger than 3/4"
Chapter 1 Solutions
Materials for Civil and Construction Engineers (2nd Edition)
Ch. 1 - State three examples of a static load application...Ch. 1 - A material has the stressstrain behavior shown in...Ch. 1 - A tensile load of 50.000 lb is applied to a metal...Ch. 1 - A tensile load of 190 kN is applied to a round...Ch. 1 - A cylinder with a 6.0 in. diameter and 12.0 in....Ch. 1 - A metal rod with 0.5 inch diameter is subjected to...Ch. 1 - A rectangular block of aluminum 30 mm 60 mm 90...Ch. 1 - A plastic cube with a 4 in. 4 in. 4 in. is...Ch. 1 - A material has a stressstrain relationship that...Ch. 1 - On a graph, show the stressstrain relationship...
Ch. 1 - The rectangular block shown in Figure P1.11 is...Ch. 1 - The rectangular metal block shown in Figure P1.11...Ch. 1 - A cylindrical rod with a length of 380 mm and a...Ch. 1 - A cylindrical rod with a radius of 0.3 in. and a...Ch. 1 - A cylindrical rod with a diameter of 15.24 mm and...Ch. 1 - The stressstrain relationship shown in Figure...Ch. 1 - A tension test performed on a metal specimen to...Ch. 1 - An alloy has a yield strength of 41 ksi, a tensile...Ch. 1 - Prob. 1.21QPCh. 1 - Figure P1.22 shows (i) elasticperfectly plastic...Ch. 1 - An elastoplastic material with strain hardening...Ch. 1 - A brace alloy rod having a cross sectional area of...Ch. 1 - A brass alloy rod having a cross sectional area of...Ch. 1 - A copper rod with a diameter of 19 mm, modulus of...Ch. 1 - A copper rod with a diameter of 0.5 in., modulus...Ch. 1 - Define the following material behavior and provide...Ch. 1 - An asphalt concrete cylindrical specimen with a...Ch. 1 - What are the differences between modulus of...Ch. 1 - Prob. 1.33QPCh. 1 - A metal rod having a diameter of 10 mm is...Ch. 1 - What is the factor of safety? On what basis is its...Ch. 1 - Prob. 1.36QPCh. 1 - Prob. 1.37QPCh. 1 - A steel rod, which is free to move, has a length...Ch. 1 - In Problem 1.38, if the rod is snugly fitted...Ch. 1 - A 4-m-long steel plate with a rectangular cross...Ch. 1 - Estimate the tensile strength required to prevent...Ch. 1 - Prob. 1.42QPCh. 1 - Briefly discuss the variability of construction...Ch. 1 - In order to evaluate the properties of a material,...Ch. 1 - A contractor claims that the mean compressive...Ch. 1 - A contractor claims that the mean compressive...Ch. 1 - Prob. 1.47QPCh. 1 - Prob. 1.48QPCh. 1 - Prob. 1.49QPCh. 1 - Briefly discuss the concept behind each of the...Ch. 1 - Referring to the dial gauge shown in Figure P1.51,...Ch. 1 - Repeat Problem 1.51 using the dial gauge shown in...Ch. 1 - Measurements should be reported to the nearest...Ch. 1 - During calibration of an LVDT, the data shown in...Ch. 1 - During calibration of an LVDT, the data shown in...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- In a ready-mix plant, cylindrical samples are prepared and tested periodically to detect any mix problem and to ensure that the compressive strength is higher than the lower specification limit. The minimum target value was at 42.0 MPa. The following compressive strength data were collected:All in Mega-Pascal (MPa)38.3, 42.5, 39.6, 41.8, 42.5, 39.3, 41.2, 40.9, 39.8, 41.642.9, 43.4, 39.9, 44.7, 45.1, 43.9, 42.4, 41.7, 41.1, 42.1Calculate the Arithmetic Mean, Median, and Standard Deviation.arrow_forwardWhile measuring the abrasion value of sub-base aggregates category E sample was taken having dry weight of 10000 grams.Amount of fines passing through 1.7 mm sieve was 1550 grams. Workout the abrasion value of aggregates.arrow_forwardA contractor claims that the mean compressive strength for a concrete mix is 5,000 psi and that it has a standard deviation of 400 psi. If you break 20 cylinders and obtain a mean compressive strength of 4,800 psi, would you believe the contractor’s claim? Why? (Hint: Use statistical t-test.)arrow_forward
- MAKE A CONCLUSION ABOUT THE EXPERIMENT MOISTURE CONTENT OF AGGREGATESarrow_forwardSpecific Gravity and Absorption of Coarse Aggregates What are the possible discussion of observations for specific gravity and absorption of aggregate to observed values?arrow_forwardTesting Procedure for Unit Weight of Aggregate.arrow_forward
- In the ultrasound test performed in the axial direction on a 75x75x285 mm edge concrete prism weighing 850 g, it was measured that the sound passed through the 285 mm length in 78 microseconds. It was determined that a sample made of the aforementioned concrete made a unit shortening of 7.4x10-4 under 200 kgf/cm2 tension. The f - ε behavior of concrete is represented by the SMITH-YOUNG function. Calculate the possible compressive strength of the concrete in question. (Take the value of e as 2.71.)arrow_forwardIn the ultrasound test performed in the axial direction on a 75x75x285 mm edge concrete prism weighing 850 g, it was measured that the sound passed through the 285 mm length in 78 microseconds. It was determined that a sample made of the aforementioned concrete made a unit shortening of 7.4x10-4 under 200 kgf/cm2 tension. The f - ε behavior of concrete is represented by the SMITH-YOUNG function. Calculate the possible compressive strength of the concrete in question. (Take the value of e as 2.71.) V= ?km/s δ= ? kg/dm³ E= ?kgf/cm² ε0= ?. x10-3 fc= kgf/cm² = MPa ?arrow_forwardA sieve analysis test was performed on a sample of aggregate and produced the results shown in Table .Calculate the percent passing through each sieve. Plot the percent passingversus sieve size on:a. a semilog gradation chart, andb. a 0.45 gradation chart (Figure A.25).What is the maximum size? What is the nominal maximum size?arrow_forward
- A concrete cylinder sample has a diameter of 6 inches and a height of 12 inches. The maximum load carried by the sample after its failure is 500 KN. Determine the compressive strength of the sample in psi. (use 1lbf = 4.45 N, round-up your answer to the nearest whole number that is divisible by 5, no need for unit)arrow_forwardA concrete test cylinder with a cross-sectional area of 28.3 in squared is to be tested in axial compression. Before loading two marks are scribed on the cylinder precisely 8 in apart (as shown in the figure below) when the load is 40,000 lb the marks are measured and found to be 7.997 in apart determine the E value for this concrete. Assume an approximately linear relationship between stress and strain.arrow_forwardA sieve analysis test was performed on a sample of coarse aggregate and produced the results in Tablea. Calculate the percent passing through each sieve.b. What is the maximum size?c. What is the nominal maximum size?d. Plot the percent passing versus sieve size on a semilog gradation chart.e. Plot the percent passing versus sieve size on a 0.45 gradation chart.f. Referring to Table (ASTM C33), what is the closest size number anddoes it meet the gradation for that standard size?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Structural Analysis (10th Edition)Civil EngineeringISBN:9780134610672Author:Russell C. HibbelerPublisher:PEARSONPrinciples of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
- Fundamentals of Structural AnalysisCivil EngineeringISBN:9780073398006Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel LanningPublisher:McGraw-Hill EducationTraffic and Highway EngineeringCivil EngineeringISBN:9781305156241Author:Garber, Nicholas J.Publisher:Cengage Learning
Structural Analysis (10th Edition)
Civil Engineering
ISBN:9780134610672
Author:Russell C. Hibbeler
Publisher:PEARSON
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781337705028
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Fundamentals of Structural Analysis
Civil Engineering
ISBN:9780073398006
Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning
Publisher:McGraw-Hill Education
Traffic and Highway Engineering
Civil Engineering
ISBN:9781305156241
Author:Garber, Nicholas J.
Publisher:Cengage Learning