Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
10th Edition
ISBN: 9780073398204
Author: Richard G Budynas, Keith J Nisbett
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 1, Problem 14P
Determinations of the ultimate tensile strength Swt of stainless-steel sheet (17-7PH, condition TH 1050), in sizes from 0.016 to 0.062 in. in 197 tests combined into seven classes were
Swt (kpsi) | | 174 | 182 | 190 | 198 | 206 | 214 | 222 |
f | 6 | 9 | 44 | 67 | 53 | 12 | 6 |
where Swt is the class midpoint and f is the class frequency. Estimate the mean and standard deviation.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
The volume of water in commercially supplied fresh drinking water containers is approximately normally distributed with mean 70 liters and standard deviation 0.75 liters. Estimate the proportion of containers likely to contain a) in excess of 70.9 liters, b) at most 68.2 liters, c) less than 70.5 liters.
Materials of Interest: CuFeS, in a silica matrix, 1.5% Cu (4.3318% CuFeS,); Top Size = 1.5 cm; CuFeS, grain size = 0.01 cm Desired sampling accuracy: +0.02% Cu, certainty of 0.99 (2.576 standard deviations) CuFeS, specific gravity=4.2: Overall specific gravity 2.8 Broad size distribution. Determine the minimum sample weight (in grams) needed for testing.
compute the 95 confidence intervals for the inventory of a series of 12 replication of the simulation of a system, where the VERAGE INVENtory is 1000 units and sample standard deviation is 38
Chapter 1 Solutions
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
Ch. 1 - Select a mechanical component from Part 3 of this...Ch. 1 - Select a mechanical component from Part 3 of this...Ch. 1 - Select an organization listed in Sec. 16, go to...Ch. 1 - Go to the Internet and connect to the NSPE website...Ch. 1 - Go to the Internet and connect to the NSPE website...Ch. 1 - Estimate how many times more expensive it is to...Ch. 1 - The costs to manufacture a part using methods A...Ch. 1 - A cylindrical part of diameter d is loaded by an...Ch. 1 - When one knows the true values x1 and x2 and has...Ch. 1 - Use the true values x1 = 7 and x2 = 8 (a)...
Ch. 1 - A solid circular rod of diameter d undergoes a...Ch. 1 - A fatigue test is performed on rotating beam...Ch. 1 - Determinations of the ultimate tensile strength...Ch. 1 - The lives of parts are often expressed as the...Ch. 1 - The tensile 0.2 percent offset yield strength of...Ch. 1 - A mechanical system comprises three subsystems in...Ch. 1 - From See. 3-12, the maximum shear stress in a...Ch. 1 - A round cold-drawn 1045 steel rod has a mean...Ch. 1 - A beam subjected to axial loading will experience...Ch. 1 - Three blocks A, B, and C and a grooved block D...Ch. 1 - The volume of a rectangular parallelepiped is...Ch. 1 - A pivot in a linkage has a pin in the figure whose...Ch. 1 - A circular cross section O ring has the dimensions...Ch. 1 - Prob. 25PCh. 1 - Prob. 26PCh. 1 - Prob. 27PCh. 1 - Prob. 28PCh. 1 - Convert the following to appropriate ips units:...Ch. 1 - Convert the following to appropriate SI units: (a)...Ch. 1 - Generally, final design results are rounded to or...Ch. 1 - Repeal Prob. 1-31 for the following: (a) = F/wt,...Ch. 1 - Repeat Prob. 131 for: (a) = F/A, where A = d2/4, F...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A manufacturer claims that the average tensile strength of thread A exceeds the average tensile strength of thread B by at least 12 kilograms. To test this claim, 50 pieces of each type of thread were tested under similar conditions. Type A thread had an average tensile strength of 86.7 kilograms with a standard deviation of 6.28 kilograms, while type B thread had an average tensile strength of 77.8 kilograms with a standard deviation of 5.61 kilograms. Test the manufacturer’s claim using a 0.05 level of significance. 1. Determine the Z calculated in two decimal places. 2. Determine the Z table in two decimal places. 3. Is the manufacturing claim statistically valid? yes or noarrow_forwardThe following data provide the time in months from hire to promotion to manager for a random sample of 25 software engineers from all software engineers employed by a large telecommunications firm. 5 7 229 453 12 14 18 14 14 483 22 21 25 23 24 34 37 34 49 64 47 67 69 192 125 Calculate the mean, variance, and standard deviation for this sample.arrow_forwardMr. C studies the strength of the material used for a baseball bat, he knows that the strength is approximately normally distributed with a standard deviation of 175 psi. A random sample 30 specimens has a mean strength of 2,750 psi. a) What is the z-value when the mean strength is tested to be 3,000 psi, b) What will be the decision for the hypothesis testing with a=0.05 c) What is the minimum mean tensile strength needed from 30 samples, for the claim of 3,000 psi to be failed to rejected.arrow_forward
- A process converts lead to gold. However, the production varies due to the power of the alchemist. It is known that the process is normally distributed with a standard deviation of 2.5g. How many samples must be taken to be 90% certain that an estimate of the mean process is within 1.5g of the true but unknown mean yield?arrow_forwardPressure distribution measurements are made on a two-dimensional wing model placed in a wind tunnel. The difference between the static pressure sockets on the surface and the static pressure of the free stream is measured. 30 data is taken at each measurement point. The average of the values measured from one of the sockets near the trailing edge was calculated as 2.30 Pa, and the standard deviation was calculated as 2.65 Pa. After applying the Chauvenet criterion to these measurement values, it was decided to eliminate 3 measurements and the new mean value was found to be 2.18 Pa and the standard deviation was 2.42. It was verified that the unexcluded data fit the normal distribution curve. Data above how many Pa and below how many Pa were eliminated? Estimate how many data have negative value (?<0) after elimination.arrow_forwardTen replicate analysis of the concentration of mercury in a sample of commercial gas condensed to give the following results 23.3 , 22.5 , 21.9 , 21.5, 19.9 , 21.3 , 21.7 , 23.8 , 22.6 , 24.7 Calculate the mean, standard deviation, RSD and 99% confidence limitarrow_forward
- Two soft drink machines dispense liquids of 10 ounces, on the average. The question is whether the two machines are equally consistent in the dispensing of the liquid. To answer this question, a sample of size 10 was obtained from each machine and the sample standard deviations were computed to be s1 = 1.87 ounces and s2 = 1.25 ounces. Perform the appropriate test of hypothesis using α = 0.05arrow_forwardBearing used in an automotive application has a nominal inside diameter of 3.81 is expected to be cm.A random sample of 25 bearings is selected andaverage inner diameter of bearing3.8037 cm. exists as. bearing inner diameter σ=0.03 cm Standard deviation of is known to be normally distributed. α=0.01 ; a) Test whether the bearing used has a nominal inside diameter of 3.81 cm. b) How to answer the question in part (a) by constructing a two-sided confidence interval on the mean diameter?explain that you can answerarrow_forwardBearing used in an automotive application has a nominal inside diameter of 3.81 is expected to be cm.A random sample of 25 bearings is selected andaverage inner diameter of bearing3.8037 cm. exists as. bearing inner diameter σ=0.03 cm Standard deviation ofis known to be normally distributed. α=0.01 ; a) Test whether the bearing used has a nominal inside diameter of 3.81 cm. b) How to answer the question in part (a) by constructing a two-sided confidence interval on the mean diameter?explain that you can answer note: can you write the solutions legibly.arrow_forward
- Suppose you have conducted 25 measurements of a random variable (Temperature) and obtained the following data in Table 2 below: Calculate the sample mean temperature, standard deviation, and standard deviation of the means of these temperature measurements. Estimate 95% confidence interval for true mean temperature. Determine the range within which the true mean temperature exists at a 95% confidence level based on this finite datasetarrow_forwardSome engineering components have a mean length of 20 mm and a standard deviation of 0.25mm. Assume that the data on the lengths of the components is normally distributed. In a batch of 50 components, determine the number of components likely to:i) Have a length of less than 19.95mmii) Be between 19.95mm and 20.15 mmiii) Be longer than 20.54 mmarrow_forwardWhat is the 95% confidence interval for each of the three measured parameters?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
How Shell and Tube Heat Exchangers Work (Engineering); Author: saVRee;https://www.youtube.com/watch?v=OyQ3SaU4KKU;License: Standard Youtube License