(a)
Sketch the power delivered to the element for
(a)
Explanation of Solution
Given data:
Refer to Figure 1.27 in the textbook for required data.
Formula used:
Write the expression for power delivered to the element as follows:
Here,
Calculation:
From the given current waveform, write the expression for current for 0 to 2 s as follows:
From the given current waveform, substitute
From the given current waveform, write the expression for current for 2 to 4 s as follows:
From the given current waveform, substitute
From the given voltage waveform, write the expression for voltage for 0 to 2 s as follows:
From the given voltage waveform, write the expression for voltage for 2 to 4 s as follows:
Modify the expression in Equation (1) for the power delivered to the element for 0 to 2 s as follows:
Substitute 5 V for
Modify the expression in Equation (1) for the power delivered to the element for 2 to 4 s as follows:
Substitute
From the calculation, write the expression for power delivered to the element as follows:
From the expression of power, draw the waveform for power delivered to the element as shown in Figure 1:
Conclusion:
Thus, the waveform for power delivered to the element is sketched.
(b)
Find the amount of energy absorbed by the element for the period of
(b)
Answer to Problem 16P
The amount of energy absorbed by the element for the period of
Explanation of Solution
Formula used:
Write the expression for energy as follows:
Here,
Calculation:
From Part (b), the expression for power delivered to the element is written as follows:
Substitute 0 s for
Rewrite the expression as follows:
Substitute
Simplify the expression as follows:
Conclusion:
Thus, the amount of energy absorbed by the element for the period of
Want to see more full solutions like this?
Chapter 1 Solutions
FUNDAMENTALS OF ELEC.CIRC.(LL)-W/ACCESS
- Solve the following problems with complete solutions and units using 2 decimal digits: A 1,000 ft. of aluminum wire, whose diameter is 0.365 in., has a resistance of 0.13 Ω at 20°C. What is its percent conductivity?arrow_forwardCharge entering the positive end of an element q = 5 sin (4π t) mC while your element voltage at the ends of v = 3 cos (4π t) V given as. Power transferred to the element at t = 0.3 s Find.arrow_forwardA coil of Nichrome wire is 23.0 m long. The wire has a diameter of 0.400 mm and is at 20.0°C. (a) If it carries a current of 0.600 A, what is the magnitude of the electric field in the wire?(b) If it carries a current of 0.600 A, what is the power delivered to it?(c) If the temperature is increased to 300°C and the potential difference across the wire remains constant, what is the power delivered? A coil of Nichrome wire is 23.0 m long. The wire has a diameter of 0.400 mm and is at 20.0°C. Your response is within 10% of the correct value. This may be due to roundoff error, or you could have a mistake in your calculation. Carry out all intermediate results to at least four-digit accuracy to minimize roundoff error.arrow_forward
- For an electrical component, the formulas for charge and voltage are given below. A is 9 coulombs, B is 12 seconds, C is 3 volts, and D is 24 seconds. Give the power of this component at t = 7 sec. You must round your answer to the nearest thousandth and give your answer as an integer followed by the appropriate metric prefix and the letter that represents the units of power.arrow_forwardPlease provide Handwritten answer. Consider a Si sample at 300 K where the total, sum of drift and diffusion current densities, of electrons is -40 A/cm2. The electron mobility is 960 cm2/V-sec throughout the sample, and the electron concentration varies as n(x) = 1016 exp (-x/0.0012) cm-3 (note that x is measured in centimeters). Determine the Electric field as a function of x which must exist in the samplearrow_forward1.) An incandescent lamp, rated at 100 watts, gives a certain amount of light when placed across the 120V ac power line. Would the amount of light increase, decrease or remain the same, when the lamp is placed across a 120V dc power line? Discuss. 2.) Explain what is meant by effective current and effective voltage.arrow_forward
- 10: Which energy can produde 2 trillion watts of electricity? a. Ocean Wave Energy b. OTEC c. Wind d. Fuel cell 11: A PV module can produce electricity by using fuel and oxidant. Select one: True Falsearrow_forward3. If the current flowing through an element is given by?(?) = {?? ?, ? ≤ ? ≤ ? ????, ? ≤ ? ≤ ?? ?−???, ?? ≤ ? ≤ ?? ??, ? ≥ ?? ?Plot the charge stored in the element over ? ≤ ? ≤ ?? ?4. A rechargeable flashlight battery is capable of delivering 80 mA for about 12 h. Howmuch charge can it release at the rate? If its terminal voltage is 1.5 V, how much energycan the battery deliver in joules?5. CEVECO charges customers as follows:Monthly charge P300.00First 250 kWh @ P2/kWhAll additional kWh @ P4/kWhIf a customer uses 2,436 kWh in one month, how much will CEVECO charge?arrow_forwardExplain the various methods of power generation in a power system, including fossil fuels, nuclear, and renewable sources.arrow_forward
- The construction of PV solar cells uses a number of critical elements. One is indium an ingredient of the transparent conducting coating on the surface of the cell. The average material intensity for indium in solar cells is approximately 0.05 kg/kWnom. Calculate the quantity of indium that would be required for a project that would provide PV solar power with capacity factor of 0.25, sufficient to meet one third of the present needs of the US, population 301 million, each using an average of 10.2 kW. The current world production of Indium is 600 tones per year. If the solar project were to be implemented over a 5 year time span, is it true that the supply of indium be adequate?arrow_forwardFind the energy delivered to an element between 0 and 8 ms if the charge entering the positive terminal is q = 10 cos 125 πt mC and the voltage is v = 6 sin 125 πt Varrow_forwardCharge entering the positive end of an element q = 5 sin (4π t) mC while your element voltage at the ends of v = 3 cos (4π t) V given as. Transferred to the element in the range of 0 to 0.6 s Calculate the energy.arrow_forward
- Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSONDelmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage LearningProgrammable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
- Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill EducationElectric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSONEngineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,