Consider steady heat transfer between two large parallel plates at constant temperatures of
Trending nowThis is a popular solution!
Chapter 1 Solutions
FUND.OF HEAT+MASS TRANSFER(LL) >CUSTOM<
- A group of 25 power transistors, dissipating 1.5 W each, are to be cooled by attaching them to a black-anodized square aluminum plate and mounting the plate on the wall of a room at 30°C. The emissivity of the transistor and the plate surfaces is 0.9. Assuming the heat transfer from the back side of the plate to be negligible and the temperature of the surrounding surfaces to be the same as the air temperature of the room, determine the size of the plate if the average surface temperature of the plate is not to exceed 50°C.arrow_forwardA 2-m × 1.8-m section of wall of an industrial furnace burning natural gas is not insulated, and the temperature at the outer surface of this section is measured to be 80°C. The temperature of the furnace room is 30°C, and the combined convection and radiation heat transfer coefficient at the surface of the outer furnace is 10 W/m2·C. It is proposed to insulate this section of the furnace wall with perlite insulation (k = 0.052 W/m·C) in order to reduce the heat loss by 90 percent, Assuming the outer surface temperature of the metal section still remains at about 80°C, determine the thickness of the insulation that needs to be used.arrow_forwardDoes any of the energy of the sun reach the earth by conduction or convection?arrow_forward
- 2.A person stands in front of a fire at 650°C in a room where air is at 5°C. Assuming the body temperature to be 37°C and a connection coefficient of 6 W/m²K, the area exposed to convection as 0.6m2, determine the net heat flow from the body. The fraction of radiation from the fire of 1m² are reaching the person is 0.01arrow_forwardA 2-m x 1.8-m section of wall of an industrial furnace burning natural gas is not insulated, and the temperature at the outer surface of this section is measured to be 80°C. The temperature of the furnace room is 30°C, and the combined convection and radiation heat transfer coefficient at the surface of the outer furnace is 10 W/m² • °C. It is proposed to insulate this section of the furnace wall with expanded perlite insulation (k = 0.052 W/m • °C) in order to reduce the heat loss by 90%. Assuming the outer surface temperature of the metal section still remains at about 80°C, determine the thickness of the insulation that needs to be used. ANSWER:_______cmarrow_forwardConsider steady heat transfer between two large parallel plates at constant temperature of T1 = 500K and T2 =300K that are L =2 cm apart. Assuming the surfaces to be black ( emissivity Ɛ = 1 ), determine the rate of heat transfer between the plates per unit surface area assuming the gap between the plate filled with atmospheric air, (b) evacuated, (c) filled with fiberglass insulation, and (d) filled with superinsulation having an apparent thermal conductivity of 0.00015 W/m.˚C.arrow_forward
- A 50-cm * 50-cm circuit board that contains 121 square chips on one side is to be cooled by combined natural convection and radiation by mounting it on a vertical surface in a room at 25°C. Each chip dissipates 0.18 W of power, and the emissivity of the chip surfaces is 0.7. Assuming the heat transfer from the back side of the circuit board to be negligible, and the temperature of the surrounding surfaces to be the same as the air temperature of the room, determine the surface temperature of the chips. Evaluate air properties at a film temperature of 30°C and 1 atm pressure. Is this a good assumption?arrow_forwardConsider steady heat transfer between two large parallel plates at constant temperatures T1 = 300 K and T2 = 200 K that are L = 1 cm apart, as shown below. Assuming the surface to be black, determine the rate of heat transfer between the plates per unit surface area assuming the gap between the plates is a) filled with still air with k = 0.0219 W/moC, b) free flowing air with h = 7.5 W/m2oC, c) evacuated, d) filled with urethane insulation with k = 0.026 W/moC, and e) filled with superinsulation that has an apparent thermal conductivity k = 0.00002 W/moCarrow_forward1. A 1000-W iron is left on the iron board with its base exposed to the air at 20°C. The convection heat transfer coefficient between the base surface and the surrounding air is 35 W/m². °C. If the base has an emissivity of 0.6 and a surface area of 0.02 m², determine the temperature of the base of the iron. 2. The inner and outer surfaces of a 5-m x 6-m brick wall of thickness 30 cm and thermal conductivity 0.69 W/m °C are maintained at temperatures of 20°C and 5°C, respectively. Determine the rate of heat transfer through the wall, in W.arrow_forward
- Consider a person standing in a room maintained at 20°C at all times. The inner surfaces of the walls, floors, and the ceiling of the house are observed to be at an average temperature of 15°C in winter and 30°C in summer. Determine the rate of radiation heat transfer between this person and the surrounding surfaces if the exposed surface area and the average outer surface temperature of the person are 1.2 m2 and 34°C, respectively. Given: εskin = 0.95, σ = 5.67x10^(-8) W/(m^2∙K^4 ). Heat Radiation in Winter (W) = Heat Radiation in Summer (W) =arrow_forwardConsider steady heat transfer between two large parallel plates at constant temperatures T1 = 300 K and T2 = 200 K that are L = 1 cm apart, as shown below. Assuming the surface to be black, determine the rate of heat transfer between the plates per unit surface area assuming the gap between the plates is a) filled with still air with k = 0.0219 W/m°C, b) free flowing air with h = 7.5 W/m2°C, c) evacuated, d) filled with urethane insulation with k = 0.026 W/m°C, and e) filled with superinsulation that has an apparent thermal conductivity k = 0.00002 W/m°Carrow_forwardConsider steady heat transfer between two large parallel plates at constant temperatures T1 = 300 K and T2 = 200 K that are L = 1 cm apart, as shown below. Assuming the surface to be black, determine the rate of heat transfer between the plates per unit surface area assuming the gap between the plates is a) filled with still air with k = 0.0219 W/m°C, b) free flowing air with h = 7.5 W/m2°C, c) evacuated, d) filled with urethane insulation with k = 0.026 W/m°C, and e) filled with superinsulation that has an apparent thermal conductivity k = 0.00002 W/m°C PLEASE ANSWER LETTER D AND E, THANK YOUarrow_forward
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning